Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder

for Preparation Click here


DESCRIPTION

The main body ECU (network gateway ECU) receives switch signals from the door control switch, and driver side door key cylinder switch, activates the door lock motor on each door accordingly.

WIRING DIAGRAM


B387094E01


B387095E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DOOR LOCK OPERATION
  1. Proceed to the next step according to the symptom listed in the table below.
    Result 
    Result
    Proceed to
    Doors cannot be locked through power window regulator master switch assembly
    A
    Doors cannot be locked through power window regulator switch assembly*1
    B
    Doors cannot be locked through driver side door key cylinder*2
    C

    1. *1: w/ Passenger Side Door Control Switch
    2. *2: w/ Key-linked Switch



B
Go to step 6

C
Go to step 10
A


2.READ VALUE USING GTS (DOOR LOCK SW-LOCK AND DOOR LOCK SW-UNLOCK)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the GTS, read the Data List.


Main Body 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Lock SW-Lock
Door control switch (power window regulator master switch assembly) lock signal / OFF or ON
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed
ON: Lock side of door control switch (power window regulator master switch assembly) pushed
-
Door Lock SW-Unlock
Door control switch (power window regulator master switch assembly) unlock signal / OFF or ON
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed
ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
-

OK:
When the switch is operating, the GTS should display as shown in the table.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

3.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B312538E03
  1. Remove the power window regulator master switch assembly (Click here).

  1. Connect the E8*1 or F6*2 power window regulator master switch assembly connector.

  1. *1: for LHD
  2. *2: for RHD
  1. Connect the cable to the negative(-) battery terminal.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage (for LHD):
Tester Connection
Switch Condition
Specified Condition
E8-16 - E8-5 (GND)
Lock switch pushed
9.15 V or higher
off
Below 1 V
E8-15 - E8-5 (GND)
Unlock switch pushed
9.15 V or higher
off
Below 1 V

Standard Voltage (for RHD):
Tester Connection
Switch Condition
Specified Condition
F6-16 - E8-5 (GND)
Lock switch pushed
9.15 V or higher
off
Below 1 V
F6-15 - E8-5 (GND)
Unlock switch pushed
9.15 V or higher
off
Below 1 V

Text in Illustration 
*A
for LHD
*B
for RHD
*a
Component with harness connected
(Power Window Regulator Master Switch Assembly (Door Control Switch))


NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - JUNCTION BLOCK AND BODY GROUND)
  1. for LHD:

    1. Disconnect the 3A instrument panel junction block assembly connector.

    2. Disconnect the E8 power window regulator master switch assembly (door control switch) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3A-51 - E8-16
      Always
      Below 1 Ω
      3A-30 - E8-15
      Always
      Below 1 Ω
      E8-5 (GND) - Body ground
      Always
      Below 1 Ω
      3A-51 or E8-16 - Body ground
      Always
      10 kΩ or higher
      3A-30 or E8-15 - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Disconnect the 3A instrument panel junction block assembly connector.

    2. Disconnect the F6 power window regulator master switch assembly (door control switch) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3A-51 - F6-16
      Always
      Below 1 Ω
      3A-30 - F6-15
      Always
      Below 1 Ω
      F6-5 (GND) - Body ground
      Always
      Below 1 Ω
      3A-51 or F6-16 - Body ground
      Always
      10 kΩ or higher
      3A-30 or F6-15 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


B317017E02


Text in Illustration 
*a
Component without harness connected
(Instrument Panel Junction Block Assembly)
-
-
  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
MB-17 (L) - 3A-51
Always
Below 1 Ω
MB-19 (UL) - 3A-30
Always
Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

6.READ VALUE USING GTS (DOOR LOCK SW-LOCK AND DOOR LOCK SW-UNLOCK)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the GTS, read the Data List.


Main Body 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Lock SW-Lock
Door control switch (power window regulator switch assembly) lock signal / OFF or ON
OFF: Lock side of door control switch (power window regulator switch assembly) not pushed
ON: Lock side of door control switch (power window regulator switch assembly) pushed
-
Door Lock SW-Unlock
Door control switch (power window regulator switch assembly) unlock signal / OFF or ON
OFF: Unlock side of door control switch (power window regulator switch assembly) not pushed
ON: Unlock side of door control switch (power window regulator switch assembly) pushed
-

OK:
When the switch is operating, the GTS should display as shown in the table.



NG
Go to step 7
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

7.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B312539E02
  1. Remove the power window regulator switch assembly (Click here).

  1. Connect the F6 power window regulator switch assembly connector.

  1. Connect the cable to the negative(-) battery terminal.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F6-16 - F6-5 (GND)
Lock switch pushed
9.15 V or higher
off
Below 1 V
F6-15 - F6-5 (GND)
Unlock switch pushed
9.15 V or higher
off
Below 1 V

Text in Illustration 
*a
Component with harness connected
(Power Window Regulator Switch Assembly (Door Control Switch))


NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (POWER WINDOW SWITCH - JUNCTION BLOCK AND BODY GROUND)
  1. Disconnect the 3A and 3B instrument panel junction block assembly connectors.

  1. Disconnect the F6 power window regulator switch assembly (door control switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-41 - F6-16
    Always
    Below 1 Ω
    3B-20 - F6-15
    Always
    Below 1 Ω
    F6-5 (GND) - Body ground
    Always
    Below 1 Ω
    3A-41 or F6-16 - Body ground
    Always
    10 kΩ or higher
    3B-20 or F6-15 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


B312649E02


Text in Illustration 
*a
Component without harness connected
(Instrument Panel Junction Block Assembly)
-
-
  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance:

Tester Connection
Condition
Specified Condition
MB-17 (L) - 3A-41
Always
Below 1 Ω
MB-19 (UL) - 3B-20
Always
Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

10.READ VALUE USING GTS (DOOR KEY SW-LOCK AND DOOR KEY SW-UNLOCK)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the GTS, read the Data List.


Main Body 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Door Key SW-Lock
Door key-linked lock switch signal/ ON or OFF
ON: Driver side door side key cylinder is turned to lock position
OFF: Driver side door key cylinder is turned to unlock position
-
Door Key SW-ULock
Door key-linked unlock switch signal/ ON or OFF
ON: Driver side door key cylinder is turned to unlock position
OFF: Driver side door key cylinder is turned to lock position
-

OK:
ON (driver side door key cylinder is turned to lock/unlock position) appears on the tester screen.



NG
Go to step 11
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

11.INSPECT FRONT DOOR LOCK ASSEMBLY RH
  1. Remove the front door lock assembly RH (Click here).

  1. Inspect the front door lock assembly RH (Click here).



NG
REPLACE FRONT DOOR LOCK ASSEMBLY RH (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK AND BODY GROUND)
  1. Disconnect the D5 main body ECU (network gateway ECU) connector.

  1. Disconnect the F3 front door lock assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D5-12 (UL2) - F3-5
    Always
    Below 1 Ω
    D5-11 (L2) - F3-6
    Always
    Below 1 Ω
    F3-8 (E) - Body ground
    Always
    Below 1 Ω
    D5-12 (UL2) or F3-5 - Body ground
    Always
    10 kΩ or higher
    D5-11 (L2) or F3-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)