Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit (RHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 57 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 57 Ω.
  1. Short in CAN main bus line
  2. Short in CAN branch line
  3. Main body ECU (network gateway ECU)
  4. Combination meter assembly
  5. Certification ECU (smart key ECU assembly)*1
  6. ECM
  7. TCM*2
  8. Skid control ECU (brake actuator assembly)
  9. Steering angle sensor (spiral cable sub-assembly)
  10. Power steering ECU assembly
  11. Air conditioning control assembly*3
  12. Air bag ECU assembly
  13. CAN No. 1 junction connector
  14. CAN No. 2 junction connector
*1: w/ Entry and Start System
*2: for Automatic Transmission System
*3: for Automatic Air Conditioning System

WIRING DIAGRAM


C261304E01


C261305E01


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds,
  6. After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR SHORT IN CAN BUS LINES (ECM)
  1. Disconnect the cable from the negative (-) battery terminal.



    C248061E01
  1. Disconnect the A33 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A33-19 (CANH) - A33-18 (CANL)
    Cable disconnected from negative (-) battery terminal
    114 to 126 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 2
OK

REPLACE ECM (Click here)  

2.CHECK FOR SHORT IN CAN BUS LINES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
  1. Reconnect the A33 ECM connector.



    C261285E02
  1. Disconnect the A5 skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A5-26 (CANH) - A5-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    114 to 126 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
Go to step 3
OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (Click here)  

3.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 J/C)
  1. Reconnect the A5 skid control ECU (brake actuator assembly) connector.



    C248060E05
  1. Disconnect the wire harness connector from the D43 CAN No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    D43-1 - D43-12
    Cable disconnected from negative (-) battery terminal
    114 to 126 Ω
    Skid control ECU (brake actuator assembly)
    D43-2 - D43-13
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Combination meter assembly
    D43-3 - D43-14
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Main body ECU (network gateway ECU)
    D43-4 - D43-15
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Certification ECU (smart key ECU assembly)
    D43-5 - D43-16
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher
    DLC3
    D43-6 - D43-17
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Steering angle sensor (spiral cable sub-assembly)
    D43-7 - D43-18
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher
    PSP (option connector)
    D43-8 - D43-19
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Air bag ECU assembly
    D43-9 - D43-20
    Cable disconnected from negative (-) battery terminal
    114 to 126 Ω
    CAN No. 1 junction connector
    D43-10 - D43-21
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Air conditioning control assembly

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to Skid Control ECU (Brake Actuator Assembly)
    *c
    to Combination Meter Assembly
    *d
    to Main Body ECU (Network Gateway ECU)
    *e
    to Certification ECU (Smart Key ECU Assembly)
    *f
    to DLC3
    *g
    to Steering Angle Sensor (Spiral Cable Sub-assembly)
    *h
    to PSP (Option Connector)
    *i
    to Air Bag ECU Assembly
    *j
    to CAN No. 1 Junction Connector
    *k
    to Air Conditioning Control Assembly

    Result:
    Result
    Proceed to
    OK
    A
    NG (CAN No. 1 junction connector main line)
    B
    NG (Skid control ECU (brake actuator assembly) main line)
    C
    NG (ECU or sensor branch line)
    D
    NG (DLC3 branch line or PSP (option connector) branch line)
    E



B
Go to step 4

C
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

D
Go to step 5

E
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3 OR PSP (OPTION CONNECTOR)
A

REPLACE CAN NO. 2 JUNCTION CONNECTOR 

4.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 J/C)


    C248060E06
  1. Disconnect the wire harness connector from the A17 CAN No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    A17-5 - A17-16
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    TCM
    A17-6 - A17-17
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher
    CAN No. 2 junction connector
    A17-7 - A17-18
    Cable disconnected from negative (-) battery terminal
    114 to 126 Ω
    ECM
    A17-8 - A17-19
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Power steering ECU assembly

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to TCM
    *c
    to CAN No. 2 Junction Connector
    *d
    to ECM
    *e
    to Power Steering ECU Assembly

Result:
Result
Proceed to
OK
A
NG (CAN No. 2 junction connector main line)
B
NG (ECM main line)
C
NG (ECU or sensor branch line)
D



B
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - CAN NO. 1 J/C)

C
REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - ECM)

D
Go to step 5
A

REPLACE CAN NO. 1 JUNCTION CONNECTOR 

5.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)
  1. Reconnect all the wire harness connectors (the A17 CAN No. 1 junction connector and D43 CAN No. 2 junction connector).

  1. Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected (Click here).



    E231257E13
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D10-6 (CANH) - D10-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    57 to 63 Ω

    Text in Illustration 
    *1
    DLC3

HINT:
  1. If the resistance becomes normal (between 57 and 63 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
  2. If the resistance does not become normal (between 57 and 63 Ω) when the connector is disconnected from the ECU (or sensor), repair or replace the short circuited branch line or connector.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR