Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1905    Short in P/T Squib (LH) Circuit

DTC    B1906    Open in P/T Squib (LH) Circuit

DTC    B1907    Short in P/T Squib (LH) Circuit (to Ground)

DTC    B1908    Short in P/T Squib (LH) Circuit (to +B)

for Preparation Click here


DESCRIPTION

The front pretensioner squib LH circuit consists of the airbag ECU assembly and front seat outer belt assembly LH.
The airbag ECU assembly uses this circuit to deploy the seat belt pretensioner when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1905
  1. The airbag ECU assembly receives a line short circuit signal in the front pretensioner squib LH circuit during primary check.
  2. Front pretensioner squib LH malfunction
  3. Airbag ECU assembly malfunction
  1. Floor wire
  2. Front seat outer belt assembly LH (Front pretensioner squib LH)
  3. Airbag ECU assembly
B1906
  1. The airbag ECU assembly receives an open circuit signal in the front pretensioner squib LH circuit.
  2. Front pretensioner squib LH malfunction
  3. Airbag ECU assembly malfunction
B1907
  1. The airbag ECU assembly receives a short circuit to ground signal in the front pretensioner squib LH circuit.
  2. Front pretensioner squib LH malfunction
  3. Airbag ECU assembly malfunction
B1908
  1. The airbag ECU assembly receives a short circuit to B+ signal in the front pretensioner squib LH circuit.
  2. Front pretensioner squib LH malfunction
  3. Airbag ECU assembly malfunction

WIRING DIAGRAM


C263726E07


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the GTS (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).

1.CHECK CONNECTORS


    C241752E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the front seat outer belt assembly LH and airbag ECU assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the front seat outer belt assembly LH and airbag ECU assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the floor wire connector (on the front seat outer belt assembly LH side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

  1. Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.

    Text in Illustration 
    *1
    Front Seat Outer Belt Assembly LH
    *2
    Airbag ECU Assembly
    *3
    Floor Wire



NG
REPLACE FLOOR WIRE
OK


2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)


    C241759E06
  1. Connect the connector to the airbag ECU assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to pretensioner deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting it.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907 or B1908 is not output.

    HINT:
    Codes other than DTCs B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect SST from connector C.
    Text in Illustration 
    *1
    Front Seat Outer Belt Assembly LH
    *2
    Airbag ECU Assembly
    *a
    Front view of wire harness connector
    (to Front Seat Outer Belt Assembly LH)



NG
Go to step 3
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH (Click here)  

3.CHECK FLOOR WIRE


    C241760E06
  1. Disconnect the floor wire from the airbag ECU assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      H22-1 - Body ground
      Ignition switch ON
      Below 1 V
      H22-2 - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H22-1 - H22-2
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H22-1 - Body ground
      Always
      1 MΩ or higher
      H22-2 - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      H22-1 - H22-2
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.
      Text in Illustration 
      *1
      Front Seat Outer Belt Assembly LH
      *2
      Airbag ECU Assembly
      *3
      Floor Wire
      *a
      Front view of wire harness connector
      (to Front Seat Outer Belt Assembly LH)



NG
REPLACE FLOOR WIRE
OK


4.CHECK DTC


    C238245E01
  1. Connect the connectors to the front seat outer belt assembly LH and airbag ECU assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1905, B1906, B1907 or B1908 is not output.

    HINT:
    Codes other than DTCs B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Outer Belt Assembly LH
    *2
    Airbag ECU Assembly



NG
REPLACE AIRBAG ECU ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)