Home › Drivetrain ยท AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL > REPLACEMENT

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. DRAIN DIFFERENTIAL OIL


    C256680
  1. Using a hexagon wrench 10 mm, remove the rear differential filler plug and gasket.



    C256681
  1. Using a hexagon wrench 10 mm, remove the rear differential drain plug and gasket to drain the differential oil.



2. REMOVE REAR DRIVE SHAFT ASSEMBLY LH
(Click here)


3. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY
(Click here)


4. REMOVE REAR DIFFERENTIAL CARRIER COVER


    C120860
  1. Remove the 8 bolts.



    C120861
  1. Using a brass bar and a hammer, remove the rear differential carrier cover from the rear differential carrier assembly.

    NOTICE:
    1. Place the brass bar onto the corners of the rear differential carrier cover.
    2. Do not damage the sealing surface of the rear differential carrier.



5. SECURE REAR DIFFERENTIAL CARRIER SUB-ASSEMBLY


    C120862
  1. Secure the rear differential carrier sub-assembly to the overhaul stand with the 6 bolts.



6. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    C120868E02
  1. Using SST, remove the rear differential side gear shaft oil seal.

    SST
    09308-00010  
    Text in Illustration 
    *1
    Rear Differential Side Gear Shaft Oil Seal



7. INSTALL REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    C120912E04
  1. Using SST and a hammer, install a new 2 rear differential side gear shaft oil seals.

    SST
    09213-70011  
    09950-60010  
    09950-70010   (09951-00410, 09951-00620, 09951-07100, 09952-06010)
    Text in Illustration 
    *1
    Rear Differential Side Gear Shaft Oil Seal

    Oil seal depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    1. To ensure a proper seal, evenly tap in the rear differential side gear shaft oil seal.
    2. When installing the oil seal, tap it in until its surface is flush with the rear differential carrier.



8. INSTALL REAR DIFFERENTIAL CARRIER SUB-ASSEMBLY


    C256678
  1. Support the rear differential carrier assembly with a transmission jack.



    C256679
  1. Remove the 5 bolts, rear upper differential mount stopper and rear lower differential mount stopper.

  1. Lower the transmission jack slowly.



    C257535
  1. Using a SST, disconnect the rear drive shaft assembly from the rear differential carrier assembly as shown in the illustration.

    SST
    09520-01010  
    09520-24010   (09520-32040)



    C262320
  1. Lower the transmission jack and pull off the rear drive shaft assembly from the rear differential carrier assembly, and then remove the rear differential carrier assembly.

    HINT:
    C262321
    Tie the disconnected rear drive shaft with a rope.



9. INSTALL REAR DIFFERENTIAL CARRIER COVER


    C266479E01
  1. Apply seal packing to the rear differential carrier cover as shown in the illustration.
    Text in Illustration 
    *a
    Seal packing
    *b
    2 to 3 mm (0.0787 to 0.118 in.)

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    1. Apply the seal packing in a continuous line, approximately 2 to 3 mm (0.0787 to 0.118 in.) in diameter.
    2. Overlap the seal packing at least 10 mm (0.394 in.) at the beginning and end of application.
    3. Install the rear differential carrier cover within 3 minutes of application.



    C120860
  1. Install the rear differential carrier cover with the 8 bolts.

    Torque:
    47 N*m{ 475 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Do not fill the differential with oil or drive the vehicle immediately after installing the differential carrier cover. Leave the vehicle for at least 1 hour. Also, avoid sudden acceleration and deceleration for at least 12 hours after application.



10. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY
(Click here)


11. INSTALL REAR DRIVE SHAFT ASSEMBLY
(Click here)


12. ADD DIFFERENTIAL OIL
  1. Using a hexagon wrench 10 mm, remove the rear differential filler plug and gasket.



    C259948
  1. Add differential oil.
    Capacity
    Oil Grade
    1.10 to 1.20 liters (1.17 to 1.27 US qts, 0.97 to 1.05 Imp. qts)
    1. Toyota genuine differential gear oil LT 75W-85 GL-5 or equivalent (except for LSD)
    2. Toyota genuine differential gear oil LX 75W-85 GL-5 or equivalent (for LSD)

  1. Using a hexagon wrench 10 mm, install the rear differential filler plug together with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    1. When adding differential oil, make sure that the vehicle is level.
    2. An excessively large or small amount of differential oil may cause damage.
    3. After adding differential oil, drive the vehicle and recheck the oil level.