Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Door Courtesy Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (network gateway ECU) controls the operation of the courtesy light assembly.

WIRING DIAGRAM


E249227E02


INSPECTION PROCEDURE

HINT:
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. Check that the lights operate.

    OK:
    Each light comes on.


    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Driver Courtesy Lamp
    Driver courtesy light
    ON/OFF
    -
    Passenger Courtesy Lamp
    Passenger courtesy light
    ON/OFF
    -

Result:
Result
Proceed to
All lights do not come on
A
Courtesy light assembly RH does not come on
B
Courtesy light assembly LH does not come on
C



B
Go to step 2

C
Go to step 5
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (BATTERY - COURTESY LIGHT)
  1. Disconnect the F4 courtesy light assembly RH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F4-2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT COURTESY LIGHT ASSEMBLY
  1. Remove the courtesy light assembly RH (Click here).

  1. Inspect the courtesy light assembly RH (Click here).

OK:
Courtesy light assembly RH is normal.



NG
REPLACE COURTESY LIGHT ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - COURTESY LIGHT AND BODY GROUND)
  1. Disconnect the D5 main body ECU (network gateway ECU) connector.

  1. Disconnect the F4 courtesy light assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    D5-5 (FRCL) - F4-1
    Always
    Below 1 Ω
    F4-1 - Body ground
    Always
    10 kΩ or higher

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    D5-6 (FRCL) - F4-1
    Always
    Below 1 Ω
    F4-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

5.CHECK HARNESS AND CONNECTOR (BATTERY - COURTESY LIGHT)
  1. Disconnect the E2 courtesy light assembly LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E2-2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT COURTESY LIGHT ASSEMBLY
  1. Remove the courtesy light assembly LH (Click here).

  1. Inspect the courtesy light assembly LH (Click here).

OK:
Courtesy light assembly LH is normal.



NG
REPLACE COURTESY LIGHT ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - COURTESY LIGHT AND BODY GROUND)
  1. Disconnect the D5 main body ECU (network gateway ECU) connector.

  1. Disconnect the E2 courtesy light assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection
Condition
Specified Condition
D5-6 (FLCL) - E2-1
Always
Below 1 Ω
E2-1 - Body ground
Always
10 kΩ or higher

Standard Resistance:
for LHD:
Tester Connection
Condition
Specified Condition
D5-5 (FLCL) - E2-1
Always
Below 1 Ω
E2-1 - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)