Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System)

DTC    B1578    Immobiliser System Data Mismatch Key

for Preparation Click here


DESCRIPTION

The ECM stores this code when the combination meter assembly reference code and reference code from the main body ECU (multiplex network ECU) do not match, or when a communication error is detected between the main body ECU (network gateway ECU) and the ECM.

DTC Code
DTC Detection Condition
Trouble Area
B1578
  1. The combination meter assembly reference code and the reference code from the main body ECU (network gateway ECU) do not match.
  2. Communication error between the main body ECU (network gateway ECU) and the ECM.
  1. Harness or connector
  2. ECM
  3. Instrument panel junction block assembly
  4. Main body ECU (network gateway ECU)

WIRING DIAGRAM


B312647E03


INSPECTION PROCEDURE

NOTICE:
  1. If the main body ECU (network gateway ECU) or ECM is replaced, refer to Service Bulletin.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC
  1. Check for DTCs (Click here).

OK:
DTC B1401, B1405, B1407 and B1408 is not output



NG
GO TO DTC CHART (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (BATTERY, BODY GROUND)
  1. Disconnect the A73 and D6 main body ECU (network gateway ECU) connectors.

  1. Disconnect the 3A, 3B and 3C instrument panel junction block assembly connectors.



    B317020E01
  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
3A-27 - Body ground
Always
11 to 14 V
3C-19 - Body ground
Always
11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
3B-18 - Body ground
Always
Below 1 Ω
A73-4 (GND) - Body ground
Always
Below 1 Ω
D6-1 (GND) - Body ground
Always
Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Instrument Panel Junction Block Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.


B312643E02


Text in Illustration 
*a
Component without harness connected
(Instrument Panel Junction Block Assembly)
-
-

Standard Resistance:

Tester Connection
Condition
Specified Condition
MB-1 (BECU) - 3A-27
Always
Below 1 Ω
MB-32 (BMPX) - 3C-19
Always
Below 1 Ω
MB-11 (GND) - 3B-18
Always
Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - ECM)
  1. Disconnect the A73 main body ECU (network gateway ECU) connector.

  1. Disconnect the A35 and A36 ECM connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
A73-9 (IMO) - Body ground
Always
Below 1 V
A35-25 (IMO) - Body ground
Always
Below 1 V

Standard Resistance:
Tester Connection
Condition
Specified Condition
A73-9 (IMO) - A35-25 (IMO)
Always
Below 1 Ω
A36-4 (E01) - Body ground
Always
Below 1 Ω
A73-9 (IMO) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE ECM
  1. Temporarily replace the ECM with a new or known good one (Click here).

  1. Register the ECU communication ID (Refer to Service Bulletin).


NEXT


6.CHECK FOR DTC
  1. Check for DTCs (Click here).

OK:
DTC B1578 is not output



NG
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
OK

END