Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)

DTC    B1242    Wireless Door Lock Tuner Circuit Malfunction

for Preparation Click here


DESCRIPTION

w/o Tire Pressure Warning System
  1. This door control receiver receives signals from the transmitter and sends these signals to the main body ECU (network gateway ECU).
w/ Tire Pressure Warning System
  1. The door control receiver receives signals from the door control transmitter and sends these signals to the main body ECU (network gateway ECU) via the tire pressure warning ECU and receiver.

DTC No.
DTC Detection Condition
Trouble Area
B1242
In diagnostic mode, applicable RDA signal cannot be received 3 times in succession after the PRG signal is output from the main body ECU (network gateway ECU).
  1. Wire harness or connector
  2. Door control receiver
  3. Main body ECU (network gateway ECU)
  4. Tire pressure warning ECU and receiver*
  1. *: w/ Tire Pressure Warning System

WIRING DIAGRAM


B374184E01


B374185E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.
  3. * When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
  4. * It is necessary to perform initialization after registration of the transmitter IDs into the tire pressure warning ECU and receiver if the tire pressure warning ECU and receiver has been replaced.
    1. for Initialization (Click here)
    2. for Registration (Click here)

  1. *: w/ Tire Pressure Warning System
1.CONFIRM VEHICLE SPECIFICATION
  1. Confirm the vehicle specification.

Result 
Result
Proceed to
w/ Tire Pressure Warning System
A
w/o Tire Pressure Warning System
B


B
Go to step 3
A


2.CHECK FOR DTC (TIRE PRESSURE WARNING SYSTEM)
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

OK:
DTCs are not output.

Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 8
A

GO TO TIRE PRESSURE WARNING SYSTEM (Click here)  

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - DOOR CONTROL RECEIVER)
  1. Disconnect the D6 main body ECU (network gateway ECU) connector.

  1. Disconnect the H27 door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D6-6 (PRG) - H27-3 (PRG)
    Always
    Below 1 Ω
    D6-7 (RDA) - H27-2 (RDA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D6-6 (PRG) or H27-3 (PRG) - Body ground
    Always
    10 kΩ or higher
    D6-7 (RDA) or H27-2 (RDA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)


    B159866E08
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H27-5 (+B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H27-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Door Control Receiver)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE DOOR CONTROL RECEIVER
  1. Replace the door control receiver with a new one (Click here).


NEXT


6.REGISTER RECOGNITION CODE
  1. Perform the Registration procedures (Click here).


NEXT


7.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Check for DTC (Click here).

    OK:
    DTC is not output.



NG
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE) 

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
  1. Disconnect the D6 main body ECU (network gateway ECU) connector.

  1. Disconnect the H28 tire pressure warning ECU and receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
D6-7 (RDA) - H28-4 (BRDA)
Always
Below 1 Ω
D6-6 (PRG) - H28-5 (BPRG)
Always
Below 1 Ω

Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
D6-7 (RDA) or H28-4 (BRDA) - Body ground
Always
10 kΩ or higher
D6-6 (PRG) or H28-5 (BPRG) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - DOOR CONTROL RECEIVER)
  1. Disconnect the H28 tire pressure warning ECU and receiver connector.

  1. Disconnect the H27 door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
H28-10 (RRDA) - H27-2 (RDA)
Always
Below 1 Ω
H28-9 (RPRG) - H27-3 (PRG)
Always
Below 1 Ω

Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
H28-10 (RRDA) or H27-2 (RDA) - Body ground
Always
10 kΩ or higher
H28-9 (RPRG) or H27-3 (PRG) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)


    B159866E08
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H27-5 (+B) - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H27-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Door Control Receiver)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (POWER SOURCE, GROUND)
B375173E01
  1. Disconnect the H28 tire pressure warning ECU and receiver connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
H28-1 (IG) - Body ground
Ignition switch ON
11 to 14 V
H28-7 (+B) - Body ground
Always
11 to 14 V

Standard Resistance:
Tester Connection
Condition
Specified Condition
H28-12 (GND) - Body ground
Always
Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.REPLACE DOOR CONTROL RECEIVER
  1. Replace the door control receiver with a new one (Click here).


NEXT


13.REGISTER RECOGNITION CODE
  1. Perform the Registration procedures (Click here).


NEXT


14.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Check for DTC (Click here).

OK:
DTC is not output.



NG
Go to step 15
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE) 

15.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
  1. Replace the tire pressure warning ECU and receiver with a new one (Click here).


NEXT


16.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Check for DTC (Click here).

OK:
DTC is not output.



NG
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
OK

END (TIRE PRESSURE WARNING ECU AND RECEIVER IS DEFECTIVE)