Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM

WINDOW DEFOGGER SYSTEM > Rear Window Defogger System does not Operate

for Preparation Click here


DESCRIPTION

When the ignition switch is ON, operating the rear window defogger switch activates the rear window defogger.
  1. w/o Automatic Air Conditioning System:
    1. The rear window defogger control is performed by the main body ECU (network gateway computer). When the main body ECU (network gateway computer) receives an on signal from the rear window defogger switch, it operates the RR DEF relay for 15 minutes. Also, when the main body ECU (network gateway computer) receives an off signal from the rear window defogger switch within 15 minutes, it stops operation of the RR DEF relay.
  1. w/ Automatic Air Conditioning System:
    1. The rear window defogger control is performed by the main body ECU (network gateway computer). When the rear window defogger switch is turned on, a rear window defogger activation request signal from the air conditioner control assembly is sent to the main body ECU (network gateway computer) via the CAN communication line, and the main body ECU (network gateway computer) operates the RR DEF relay for 15 minutes. Also, when the main body ECU (network gateway computer) receives a rear window defogger off signal within 15 minutes, it stops operation of the RR DEF relay.

WIRING DIAGRAM


B315682E01


B315683E03


INSPECTION PROCEDURE

NOTICE:
  1. Perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before performing the following inspection (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING GTS (RR DEF RELAY)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. According to the display on the GTS, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Defogger
    RR DEF relay
    OFF or ON
    -

    OK:
    The window defogger system operates normally.

Result 
Result
Proceed to
NG
A
OK
B


B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A


2.INSPECT RR DEF RELAY
  1. Remove the RR DEF relay from the engine room relay block.

  1. Inspect the RR DEF relay (Click here).



NG
REPLACE RELAY (RR DEF)
OK


3.CHECK HARNESS AND CONNECTOR (RR DEF RELAY - BATTERY)


    B322122E01
  1. Remove the RR DEF relay from the engine room relay block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Ignition switch ON
    11 to 14 V
    3 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    RR DEF Relay



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (RR DEF RELAY - MAIN BODY ECU (NETWORK GATEWAY ECU))
  1. Remove the RR DEF relay from the engine room relay block assembly.

  1. Disconnect the A73 main body ECU (network gateway ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    2 - A73-24
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    2 - Body ground
    Always
    10 kΩ higher

Result 
Result
Proceed to
NG
A
OK (w/o Automatic Air Conditioning System)
B
OK (w/ Automatic Air Conditioning System)
C


B
Go to step 5

C
Go to step 7
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - HEATER CONTROL SUB-ASSEMBLY)
  1. Disconnect the D6 main body ECU (network gateway ECU) connector.

  1. Disconnect the D22 heater control sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D6-5 - D22-2 (RDEF+)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D6-5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT HEATER CONTROL SUB-ASSEMBLY
  1. Remove the heater control sub-assembly (Click here ).

  1. Inspect the heater control sub-assembly (Click here).



NG
REPLACE HEATER CONTROL SUB-ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (BACK WINDOW GLASS (REAR WINDOW DEFOGGER) - RR DEF RELAY)
  1. Disconnect the G10 and H29 rear window defogger connector.

  1. Remove the RR DEF relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    G10-1 - 5
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    H29-1 - Body ground
    Always
    Below 1 Ω
    G10-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE BACK WINDOW GLASS (REAR WINDOW DEFOGGER) (Click here)