Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER

REAR SHOCK ABSORBER > INSTALLATION

for Preparation Click here


HINT:
  1. The procedure listed below is for the LH side.
  2. Use the same procedure for the RH and LH sides.



1. INSTALL REAR SHOCK ABSORBER WITH COIL SPRING
  1. Mount the rear shock absorber with coil spring on the vehicle.

  1. Install rear shock absorber with coil spring with the 2 new nuts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



2. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
  1. Replace the mounting nuts of the rear No. 2 suspension arm assembly LH and rear suspension member sub-assembly with new nut and then temporarily tighten them.

  1. Temporarily install the rear No. 2 suspension arm assembly LH to the rear axle carrier sub-assembly LH with the bolt and new nut.

    NOTICE:
    Insert the bolt from the front of the vehicle.

  1. Temporarily install the rear shock absorber with coil spring with the bolt and new nut.

    HINT:
    The bolt may be inserted from either direction.



3. TEMPORARILY INSTALL STABILIZER LINK SUB-ASSEMBLY (for LH Side)
  1. Temporarily install the rear stabilizer link sub-assembly to the rear No. 2 suspension arm assembly LH with the bolt and new nut.



4. STABILIZE SUSPENSION


    C261010E01
  1. Jack up the axle carrier, with a wooden block placed between the jack and axle carrier, to apply load to the suspension so that the rear drive shaft assembly becomes level.
    Text in Illustration 
    *a
    Wooden Block



5. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
  1. Fully tighten the nut on the rear axle carrier sub-assembly LH side.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

  1. Fully tighten the nut holding the rear shock absorber.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

  1. Fully tighten the nut on the rear suspension member sub-assembly side.

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }



6. FULLY TIGHTEN STABILIZER LINK SUB-ASSEMBLY
  1. Fully tighten the nut rear stabilizer link sub-assembly side.

    Torque:
    38 N*m{ 388 kgf*cm , 28 ft.*lbf }



7. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ HID Headlight System)
  1. Install the rear height control sensor sub-assembly LH to the rear No. 2 suspension arm assembly LH with the nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



8. INSTALL REAR WHEEL

Torque:
120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



9. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH
  1. Install the luggage compartment inner trim cover LH with the 5 clips.



10. INSTALL REAR FLOOR FINISH PLATE
  1. Engage the 4 claws to install the rear floor finish plate.

  1. Install the 3 clips.



11. INSTALL LUGGAGE COMPARTMENT FLOOR MAT


12. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(Click here)


13. VSC SENSOR NEUTRAL MEMORIZATION
(Click here)


14. HEIGHT CONTROL SENSOR SIGNAL INITIALIZE (w/ HID Headlight System)
(Click here)


15. ADJUST HEADLIGHT AIMING (w/ HID Headlight System)
(Click here)