IGNITION SYSTEM > ON-VEHICLE INSPECTION |
| 1. PERFORM SPARK TEST |
Check for DTCs (Click here).
Remove the 4 ignition coils and 4 spark plugs (Click here).
Hoist the engine assembly up with an engine sling device and a mini crane.
![]() |
Remove the SST.
![]() |
Install the 2 nuts.
![]() |
Remove the 2 bolts and injector cover (for bank 1).
![]() |
Disconnect the 2 fuel injector connectors.
Install the injector cover (for bank 1).
![]() |
Install the injector driver with the 3 bolts.
![]() |
Disconnect the 2 fuel injector connectors.
Connect the cable to the negative battery terminal.
Install the air cleaner case sub-assembly with the hose.
Install a spark plug to each ignition coil and connect the ignition coil connector.
Ground the spark plug.
Check that spark occurs while the engine is being cranked.
Check whether sparks occur.
If spark does not occur, perform the following procedure.
| 2. INSPECT IGNITION COIL AND SPARK PLUG |
Perform the spark test in accordance with the following procedure.
Check that the wire harness side connector of the ignition coil assembly is securely connected.
| Result | Proceed to |
| NG | Connect securely |
| OK | Go to next step |
Perform a spark test on each ignition coil assembly.
| Result | Proceed to |
| OK | Replace ignition coil assembly |
| NG | Go to next step |
Perform a spark test on each spark plug.
| Result | Proceed to |
| OK | Replace spark plug |
| NG | Inspect the ignition system (Click here) |
Disconnect the cable from the negative battery terminal.
Remove the air cleaner case sub-assembly with hose.
![]() |
Remove the 3 bolts and the injector driver.
![]() |
Remove the 2 bolts and the injector cover (for bank 1).
![]() |
Connect the 2 fuel injector connectors.
Install the 2 bolts and the injector cover.
Install the 3 bolts and the injector driver.
![]() |
Connect the 4 connectors to the injector driver. Move the lock levers in the direction indicated by the arrow to lock the 3 connectors.
| *1 | Lock Lever |
![]() | Connector with Lock Lever |
![]() | Connector without Lock Lever |
![]() |
Connect the 2 fuel injector connectors.
![]() |
Install the injector cover (for bank 1) with the 2 bolts.
![]() |
Remove the 2 nuts.
Hoist the engine assembly up with an engine sling device and a mini crane.
![]() |
Install the SST.
Install the ignition coil assembly and spark plug (Click here).
Clear the DTCs (Click here).
Check for DTCs (Click here).
| 3. INSPECT SPARK PLUG |
![]() |
Check the electrode using a megohmmeter:
| *a | Ground |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Spark plug (terminal part) - Body ground | Always | 10 MΩ or higher |
Alternative inspection method:
Quickly accelerate the engine to 4000 rpm 5 times.
Remove the spark plug (Click here).
![]() |
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
| *a | Correct |
| *b | Incorrect |
Install the spark plug (Click here).
Check the spark plug for any damage to its threads and insulator.
| Manufacturer | Product |
| DENSO made | ZXE27HBR8 |
Reference:
![]() |
Using SST, check the spark plug electrode gap.
| *a | Spark Plug Electrode Gap |
Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.