SFI SYSTEM > Brake Override System |

| 1.CHECK DTC OUTPUT |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: System Select / Health Check.
Check DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 2.READ VALUE USING GTS (MASTER CYLINDER SENSOR) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Master Cylinder Sensor.
Read the value displayed on the GTS.
| GTS Display | Measurement Item/Range | Normal Condition |
| Master Cylinder Sensor | Master cylinder pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V |
|
Check that the brake fluid pressure value of the "Master Cylinder Sensor" observed on the GTS changes when the brake pedal is depressed.
|
| ||||
| OK | |
| 3.READ VALUE USING GTS (STOP LIGHT SWITCH AND ST1) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch and ST1.
Check the Data List indication when the brake pedal is depressed and released.
| GTS Display | Condition | Specified Condition |
| Stop Light Switch | Brake pedal released | OFF |
| Brake pedal depressed | ON | |
| ST1 | Brake pedal released | OFF |
| Brake pedal depressed | ON |
|
| ||||
| OK | |
| 4.INSPECT BRAKE PEDAL |
Inspect and adjust the brake pedal (for except LHD M/T) (Click here).
Inspect and adjust the brake pedal (for LHD M/T) (Click here).
| Result | Proceed to |
| OK | A |
| NG (for except LHD M/T) | B |
| NG (for LHD M/T) | C |
|
| ||||
|
| ||||
| A | |
| 5.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No. 1 Volt % and Accel Sens. No. 2 Volt %.
Read the value displayed on the GTS.
| GTS Display | Condition | Specified Condition |
| Accel Sens. No. 1 Volt % | Accelerator Pedal Released → Depressed → Released | Values smoothly change following accelerator pedal operation |
| Accel Sens. No. 2 Volt % |
|
| ||||
| OK | |
| 6.READ VALUE USING GTS (VEHICLE SPEED) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.
Read the value displayed on the GTS.
| GTS Display | Condition | Specified Condition |
| Vehicle Speed | Vehicle stopped, engine running | 0 km/h (0 mph) |
| Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) | No large fluctuations when driving at a constant speed |
|
| ||||
| OK | |
| 7.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.
Read the value displayed on the GTS.
| GTS Display | Condition | Specified Condition |
| FR Wheel Speed FL Wheel Speed RR Wheel Speed RL Wheel Speed | Vehicle stopped, engine running | 0 km/h (0 mph) |
| Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) | No large fluctuations when driving at a constant speed |
|
| ||||
| OK | ||
| ||