Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > LED open-circuit detection circuit

for Preparation Click here


DESCRIPTION

the low beam headlights do not illuminate, or a communication malfunction is detected between the headlight assembly and headlight leveling ECU assembly.

WIRING DIAGRAM


E351712E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (HEADLIGHT RELAY)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Headlight Relay
    Headlight relay
    ON/OFF
    -

    OK:
    The daytime running lights illuminate.



NG
Go to step 5
OK


2.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)
  1. Disconnect the A60 or A38 Headlight Assembly RH or LH connectors.

  1. Disconnect the A16 headlight leveling ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-8 - A16-13 (R-DIAG)
    Always
    Below 1 Ω
    A60-8 - A16-15 (L-DIAG)
    Always
    Below 1 Ω
    A38-8 or A16-13 (R-DIAG) - Body ground
    Always
    10 kΩ or higher
    A60-8 or A16-15 (L-DIAG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT HEADLIGHT LEVELING ECU ASSEMBLY


  1. Measure the voltage according to the value(s) in the table below.


    E208529E01


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A16-13 (R-DIAG) - Body ground
    Always
    Below 1.5 V
    A16-15 (L-DIAG) - Body ground
    Always
    Below 1.5 V

    Text in Illustration 
    *a
    Component without harness connected
    (Headlight Leveling ECU Assembly)



NG
REPLACE HEADLIGHT ASSEMBLY (Click here)
OK

GO TO PROBLEM SYMPTOMS TABLE (Click here)  

4.INSPECT H-LP RELAY
  1. Remove the H-LP relay from the engine room relay block.

  1. Inspect the H-LP relay (Click here).



NG
REPLACE H-LP RELAY
OK

CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY) 

5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)
  1. Remove the H-LP relay from the engine room relay block.



    E247165E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay Terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Engine Room Relay Block
    (H-LP Relay Terminal)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - MAIN BODY ECU (NETWORK GATEWAY ECU))
  1. Remove the H-LP relay from the engine room relay block.

  1. Disconnect the A73 main body ECU (network gateway ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay Terminal 2 - A73-11
    Always
    Below 1 Ω
    A73-11 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Remove the H-LP relay from the engine room relay block.

  1. Disconnect the 3C Instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay Terminal 1 - 3C-17
    Always
    Below 1 Ω
    3C-17 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3A and 3C Instrument panel junction block assembly connector.

  1. Disconnect the A73 and D5 main body ECU (network gateway ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3A-29 - D5-1 (HRLYD)
    Always
    Below 1 Ω
    3C-30 - A73-2 (HRLY)
    Always
    Below 1 Ω
    3A-29 or D5-1 (HRLYD) - Body ground
    Always
    10 kΩ or higher
    3C-30 or A73-2 (HRLY) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (See page ).


E247166E01

  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3C-17 - 3A-29
    Always
    Below 1 Ω
    3C-17 - 3C-30
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)