Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

When the brake pedal is released, terminal STP of the ECM receives positive (+) battery voltage through the ECU IG2 fuse. While depressing the brake pedal, the stop light switch sends a signal to terminals STP and ST1- of the ECM. The ECM cancels cruise control drive when terminal STP receives the signal.

WIRING DIAGRAM


A280665E01


INSPECTION PROCEDURE

HINT:
Stop light switch assembly conditions can be checked using the GTS.
  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the GTS on.
  4. Enter the following menus: Powertrain / Cruise Control / Data List / Stop Light Switch 1 and Stop Light Switch 2.

    Cruise Control 
    Brake Pedal Operation
    Stop Light Switch 1
    Stop Light Switch 2
    Depressed
    ON
    ON
    Released
    OFF
    OFF

1.CHECK ECM (TERMINAL VOLTAGE)


    A280163E03
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A33-7 (STP) - Body ground
    Brake pedal released
    11 to 14 V
    Brake pedal depressed
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 3
OK


2.CHECK ECM (TERMINAL VOLTAGE)


    A280163E04
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A33-3 (ST1-) - Body ground
    Brake pedal depressed
    11 to 14 V
    Brake pedal released
    Below 1 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 6
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)


    A280674E01
  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A22-3 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
INSPECT ECM POWER SOURCE CIRCUIT (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the ECM connector.

  1. Disconnect the stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-7 (STP) - A22-4
    Always
    Below 1 Ω


    Standard resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-7 (STP) or A22-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)  

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)


    A280674E01
  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A22-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
Go to step 9
OK


7.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the ECM connector.

  1. Disconnect the stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-3 (ST1-) - A22-2
    Always
    Below 1 Ω


    Standard resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-3 (ST1-) or A22-2 - Body ground
    Always
    10 kΩ or higher



NG
Go to step 11
OK


8.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)  

9.CHECK HARNESS AND CONNECTOR (NOISE FILTER - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the stop light switch assembly connector.

  1. Disconnect the noise filter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A22-1 - A13-2
    Always
    Below 1 Ω


    Standard resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A22-1 or A13-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


10.INSPECT NOISE FILTER
  1. Inspect the noise filter (Click here).



NG
REPLACE NOISE FILTER (Click here)
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (NOISE FILTER - BATTERY) 

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NOISE FILTER)
  1. Disconnect the stop light switch assembly connector.

  1. Disconnect the noise filter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A22-2 - A13-1
    Always
    Below 1 Ω


    Standard resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A22-2 or A13-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


12.INSPECT NOISE FILTER
  1. Inspect the noise filter (Click here).



NG
REPLACE NOISE FILTER (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (ECM - NOISE FILTER)
  1. Disconnect the ECM connector.

  1. Disconnect the noise filter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-3 (ST1-) - A13-4
    Always
    Below 1 Ω


    Standard resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-3 (ST1-) or A13-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM (Click here)