Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P1235  High Pressure Fuel Pump Circuit  


DESCRIPTION

The fuel pump assembly (for high pressure) is attached to the insulator, which is attached to the cylinder head cover. The pump activates according to the position of the cam on the intake side camshaft (bank 2).

The fuel pump assembly (for high pressure) increases the pressure of the fuel supplied from the fuel pump in the fuel tank to the specified fuel pressure according to the operating condition, and it feeds the fuel to the fuel delivery pipe.

DTC No. DTC Detection Condition Trouble Area
P1235 When fuel pump for high pressure is operating, the diagnostic signal from injector driver (EDU) does not change (open or short in the fuel pump (for high pressure) circuit).
(1 trip detection logic)
·

Open or short in fuel pump (for high pressure)

·

Fuel pump assembly (for high pressure)

·

Injector driver (EDU)

·

ECM



CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Record the Freeze Frame Data.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Based on engine speed, engine load and other freeze frame data stored in the ECM, reproduce the conditions present when the DTC was stored.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the DTC.

HINT:
·

If a DTC is output, the system is malfunctioning.

·

If a DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P1235.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shown ABNORMAL, the system has a malfunction.

·

If the judgment result shows NORMAL, the system is normal.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280075E08
5.896,0.865 6.208,1.167 0.313,0.302 10 false FPD 6.271,2.698 6.781,2.906 0.51,0.208 10 false ECM 5.781,2.698 6.052,2.875 0.271,0.177 10 false A34 5.625,0.74 5.875,1.052 0.25,0.313 10 false 32 2.052,2.271 2.854,2.573 0.802,0.302 10 false Shielded 5.885,2.01 6.271,2.313 0.385,0.302 10 false FPF 5.646,1.927 5.896,2.24 0.25,0.313 10 false 13 4.708,0.667 4.958,0.865 0.25,0.198 10 false 8 3.49,0.667 3.688,0.854 0.198,0.188 10 false 3 3.49,1.833 3.688,2.021 0.198,0.188 10 false 4 1.667,0.729 1.865,0.917 0.198,0.188 10 false 2 0.563,0.74 0.76,0.927 0.198,0.188 10 false 1 3.708,2.615 5.167,3.01 1.458,0.396 10 false Injector Driver (EDU) 4.677,0.865 4.948,1.042 0.271,0.177 10 false C1 0.5,1.385 1.958,2.042 1.458,0.656 10 false Fuel Pump Assembly (for High Pressure) 0.5,1.219 0.802,1.396 0.302,0.177 10 false C29 4.708,1.823 4.948,2.021 0.24,0.198 10 false 7 4.677,2.031 4.948,2.208 0.271,0.177 10 false C1 3.448,0.854 3.719,1.031 0.271,0.177 10 false C2 3.448,2.031 3.719,2.208 0.271,0.177 10 false C2 3.76,0.854 4.073,1.156 0.313,0.302 10 false FP- 4.24,0.854 4.542,1.156 0.302,0.302 10 false FPD 3.76,2.031 4.073,2.333 0.313,0.302 10 false FP+ 4.25,2.031 4.542,2.333 0.292,0.302 10 false FPF

CAUTION / NOTICE / HINT

HINT:
·

If the current from the INJ relay is cut because DTC P062D is stored, DTC P1235 will be stored even if the fuel pump assembly (for high pressure) is normal.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE)
a.

Inspect the fuel pump assembly (for high pressure) (See page Engine / Hybrid System>FA20 FUEL>FUEL PUMP(for High Pressure)>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - FUEL PUMP ASSEMBLY)

NG

REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE)

2.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - FUEL PUMP ASSEMBLY)
a.

Disconnect the injector driver (EDU) connector.


b.

Disconnect the fuel pump assembly (for high pressure) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
C2-3 (FP-) - C29-2 Always Below 1 Ω
C2-4 (FP+) - C29-1 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
C2-3 (FP-) or C29-2 - Body ground Always 10 kΩ or higher
C2-4 (FP+) or C29-1 - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER (EDU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER (EDU))
a.

Disconnect the ECM connector.


b.

Disconnect the injector driver (EDU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A34-32 (FPD) - C1-8 (FPD) Always Below 1 Ω
A34-13 (FPF) - C1-7 (FPF) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A34-32 (FPD) or C1-8 (FPD) - Body ground Always 10 kΩ or higher
A34-13 (FPF) or C1-7 (FPF) - Body ground Always 10 kΩ or higher




OK

4.INSPECT ECM (FPD VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ECM (FPD VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Inspect the ECM using an oscilloscope.

i.
U146757E06
1.99,1.25 2.385,1.896 true 1.938,0.385 2.229,0.573 0.292,0.188 10 false A34 0.135,0.083 0.385,0.271 0.25,0.188 10 false *a 0.188,3.156 0.542,3.344 0.354,0.188 10 false CH1 2.979,3.146 3.344,3.333 0.365,0.188 10 false GND 2.438,1.906 3.063,2.094 0.625,0.188 10 false 32(FPD) 0.156,2.24 0.406,2.427 0.25,0.188 10 false *b

While idling the engine, check the waveform the terminals of the ECM connector.

ECM Terminal Name A34-32 (FPD) - Body ground
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling

Text in Illustration
*a Component with harness connected
(ECM)
*b FPD Terminal Waveform Normal Waveform

Standard:

Signal waveform appears as shown in the illustration.


HINT:

The FPD terminal waveform is output only right after the engine starts. If this DTC is stored when the engine is started from ignition switch off, the system enters fail-safe mode and the waveform is not output.





OK

5.INSPECT ECM (FPF VOLTAGE)

NG

6.INSPECT ECM (FPD VOLTAGE)
5.INSPECT ECM (FPF VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Inspect the ECM using an oscilloscope.

i.
U146759E05
1.99,1.26 2.375,1.917 true 1.99,1.125 1.115,1.865 true 1.948,0.396 2.24,0.583 0.292,0.188 10 false A34 0.083,0.125 0.333,0.313 0.25,0.188 10 false *a 0.188,2.948 0.51,3.135 0.323,0.188 10 false CH1 2.958,3.156 3.333,3.344 0.375,0.188 10 false GND 2.427,1.927 3.052,2.115 0.625,0.188 10 false 32(FPD) 0.156,2.25 0.406,2.438 0.25,0.188 10 false *b 0.896,1.906 1.448,2.094 0.552,0.188 10 false 13(FPF) 0.052,3.135 0.469,3.323 0.417,0.188 10 false (FPD) 0.177,3.521 0.5,3.708 0.323,0.188 10 false CH2 0.052,3.688 0.469,3.875 0.417,0.188 10 false (FPF) 2.958,3.99 3.333,4.177 0.375,0.188 10 false GND

A280101E03
0.063,0.104 0.313,0.292 0.25,0.188 10 false *c 0.177,2.958 0.5,3.146 0.323,0.188 10 false CH1 2.958,3.146 3.333,3.333 0.375,0.188 10 false GND 0.135,2.365 0.385,2.552 0.25,0.188 10 false *d 0.063,3.135 0.479,3.323 0.417,0.188 10 false (FPD) 0.177,3.521 0.5,3.708 0.323,0.188 10 false CH2 0.052,3.698 0.469,3.885 0.417,0.188 10 false (FPF) 2.958,3.979 3.333,4.167 0.375,0.188 10 false GND 0.177,0.698 0.5,0.885 0.323,0.188 10 false CH1 0.052,0.865 0.469,1.052 0.417,0.188 10 false (FPD) 0.177,1.635 0.5,1.823 0.323,0.188 10 false CH2 0.052,1.813 0.469,2 0.417,0.188 10 false (FPF) 2.958,0.865 3.344,1.052 0.385,0.188 10 false GND 2.958,1.698 3.323,1.885 0.365,0.188 10 false GND

While idling the engine, check the waveform the terminals of the ECM connector.

ECM Terminal Name CH1: A34-32 (FPD) - Body ground
CH2: A34-13 (FPF) - Body ground
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling

Text in Illustration
*a Component with harness connected
(ECM)
*b FPD Terminal and FPF Terminal Waveform Normal Waveform
*c FPF Terminal Waveform NG Waveform 1
*d FPF Terminal Waveform NG Waveform 2

HINT:

*: If the FPF terminal waveform is similar to the FPF terminal waveform NG waveform 1, stop the engine and disconnect injector driver (EDU) connector. Then, while cranking the engine, check to see if there is a difference between the FPF terminal waveform and the previous one.




Result:
FPD Terminal Waveform FPF Terminal Waveform Proceed to
OK OK A
OK NG waveform 1* Does not change from NG waveform 1 (FPF terminal waveform remains at GND even after disconnecting the injector driver (EDU) connector and cranking the engine) A
Changes to NG waveform 2 (FPF terminal waveform rises from GND after disconnecting the injector driver (EDU) connector and cranking the engine) B
OK NG waveform 2 B



A

B

REPLACE INJECTOR DRIVER (EDU)

6.INSPECT ECM (FPD VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Disconnect the injector driver (EDU) connector.


c.

Inspect the ECM using an oscilloscope.

i.
U146758E05
1.99,1.25 2.385,1.896 true 1.938,0.385 2.229,0.573 0.292,0.188 10 false A34 0.094,0.115 0.344,0.302 0.25,0.188 10 false *a 0.156,3.146 0.51,3.333 0.354,0.188 10 false CH1 2.979,3.156 3.344,3.344 0.365,0.188 10 false GND 2.427,1.896 3.052,2.083 0.625,0.188 10 false 32(FPD) 0.156,2.354 0.406,2.542 0.25,0.188 10 false *b

While cranking the engine, check the waveform the terminals of the ECM connector.

ECM Terminal Name A34-32 (FPD) - Body ground
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Cranking

Text in Illustration
*a Component with harness connected
(ECM)
*b FPD Terminal Waveform Normal Waveform

Standard:

Signal waveform appears as shown in the illustration.





OK

REPLACE INJECTOR DRIVER (EDU)

NG