Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0455  Evaporative Emission Control System Leak Detected (Gross Leak)  P0456  Evaporative Emission Control System Leak Detected (Very Small Leak)  P1451  Fuel Tank Pressure Sensor Range/Performance  P2404  Evaporative Emission System Leak Detection Pump Sense Circuit Range / Performance  


DTC SUMMARY

DTC No. Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P0455 EVAP gross leak Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured. Reference pressure is measured at start and end of leak check.
If stabilized pressure is higher than [second reference pressure x 0.377], ECM determines that EVAP system has a large leak.
·

Fuel cap (loose)

·

Leakage from EVAP line (canister - fuel tank)

·

Leakage from EVAP line (purge valve - canister)

·

Leakage from canister pump module

·

Leakage from fuel tank

·

Leakage from canister


While ignition switch off 2 trip
P0456 EVAP small leak Leak detection pump creates negative pressure (vacuum) in EVAP system and EVAP system pressure is measured. Reference pressure measured at start and end of leak check.
If stabilized pressure is higher than second reference pressure, ECM determines that EVAP system has a small leak.
While ignition switch on 2 trip
P1451 EVAP clogged A blockage in the EVAP system pipe is detected.
·

Blockage in EVAP line (canister - fuel tank)

·

Blockage in EVAP line (leak detection pump - canister)

·

Blockage in canister pump module


While ignition switch on 2 trip
P2404 EVAP malfunction Leak detection pump ending pressure is more than the threshold.
The difference between the leak detection pump highest pressure and lowest pressure is the threshold value or more.
The vent valve abnormality is detected.
·

Leak detection pump


While ignition switch on 2 trip

DESCRIPTION

The description can be found in EVAP (Evaporative Emission) System (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>EVAP System).

MONITOR DESCRIPTION

5 hours*1 after the ignition switch is turned off, the leak detection pump creates negative pressure (vacuum) in the EVAP (Evaporative Emission) system. The ECM monitors for leaks and actuator malfunctions based on the EVAP pressure.

HINT:

*: If the enable conditions are not satisfied 5 hours after the ignition switch is turned off, the monitor check starts 2 hours later. If the enable conditions are still not satisfied 7 hours after the ignition switch is turned off, the monitor check starts 2.5 hours later.


Sequence Operation Duration
A Leak detection pump monitor 300 seconds
B First reference pressure measurement 40 seconds
C Vent valve monitor 12 seconds
D Pipe clogging monitor 900 seconds
E Second reference pressure measurement 40 seconds

*: If only a small amount of fuel is in the fuel tank, it takes longer for the EVAP pressure to stabilize.

A285190E02
0.552,0.573 1.01,0.573 1.01,0.573 1.229,0.927 false 1.99,0.323 1.729,0.323 1.729,0.323 1.594,1.083 false 2.167,2.615 1.906,2.615 1.906,2.615 1.615,2.198 false 0.698,2.479 1.198,2.479 1.198,2.479 1.49,1.979 true 0.49,1.917 0.792,1.917 0.792,1.917 1.115,1.75 false 2.927,0.781 2.656,0.781 2.656,0.781 2.438,1.167 false 2.844,1.281 1.969,1.281 1.969,1.281 1.75,1.594 false 2.406,1.625 2.938,1.625 false 2.573,2.104 2.906,2.104 false 4.427,0.573 4.885,0.573 4.885,0.573 5.104,0.927 false 4.677,2.698 5.177,2.698 5.177,2.698 5.469,2.198 false 6.74,1.281 5.854,1.281 5.854,1.281 5.646,1.594 false 0.552,2.938 1.021,2.938 1.021,2.938 1.229,3.292 false 0.667,4.646 1.052,4.646 1.052,4.646 1.542,4.521 false 2.865,3.635 1.99,3.635 1.99,3.635 1.771,3.948 false 0.146,0.083 0.375,0.292 0.229,0.208 10 false *a 0.104,2.667 0.333,2.875 0.229,0.208 10 false *c 4.115,0.083 4.344,0.292 0.229,0.208 10 false *b 2.052,0.25 2.302,0.5 0.25,0.25 10 false *9 2.229,2.542 2.479,2.792 0.25,0.25 10 false *5 0.552,2.406 0.802,2.656 0.25,0.25 10 false *8 0.344,1.854 0.594,2.104 0.25,0.25 10 false *7 0.344,0.49 0.594,0.74 0.25,0.25 10 false *1 2.896,1.219 3.146,1.469 0.25,0.25 10 false *3 2.938,0.688 3.188,0.875 0.25,0.188 10 false *10 2.99,1.552 3.24,1.74 0.25,0.188 10 false *11 2.938,2.01 3.188,2.198 0.25,0.188 10 false *12 4.479,2.615 4.729,2.865 0.25,0.25 10 false *6 4.271,0.5 4.521,0.75 0.25,0.25 10 false *1 6.802,1.188 7.052,1.438 0.25,0.25 10 false *3 0.469,4.573 0.646,4.719 0.177,0.146 10 false *5 0.365,2.875 0.615,3.125 0.25,0.25 10 false *1 2.938,3.552 3.188,3.802 0.25,0.25 10 false *3 5.635,3.646 5.99,3.938 0.354,0.292 10 false *d 5.635,4.198 5.99,4.49 0.354,0.292 10 false *e

Text in Illustration
*1 Purge valve: OFF (closed) *2 Purge valve: ON (open)
*3 Vent Valve: OFF (vent) *4 Vent Valve: ON (closed)
*5 Leak Detection Pump: OFF *6 Leak Detection Pump: ON
*7 Reference Orifice (0.02 inch) *8 Canister Pressure Sensor
*9 Canister *10 Fuel Tank
*11 Canister Pump Module *12 Canister Filter
*a Operation A:
Atmospheric Pressure Measurement
*b Operation B, E:
Reference Pressure Measurement
*c Operation C:
EVAP System Pressure Measurement
*d Atmospheric Pressure
*e Negative Pressure - -

(a) P0455: EVAP (Evaporative Emission) gross leak

In operation D, the leak detection pump creates negative pressure (vacuum) in the EVAP system and the EVAP system pressure is measured. If the stabilized system pressure is higher than [second reference pressure x 0.377] (near atmospheric pressure), the ECM determines that the EVAP system has a large leak, illuminates the MIL and stores the DTC (2 trip detection logic).

(b) P0456: EVAP very small leak

In operation D, the leak detection pump creates negative pressure (vacuum) in the EVAP system and the EVAP system pressure is measured. If the stabilized system pressure is higher than second reference pressure, the ECM determines that the EVAP system has a small leak, illuminates the MIL and stores the DTC (2 trip detection logic).

A281935E05
0.813,0.635 1.167,0.813 0.354,0.177 10 false ECM 1.573,0.406 1.823,0.573 0.25,0.167 10 false ON 2.156,0.74 2.406,0.906 0.25,0.167 10 false ON 1.188,0.542 1.51,0.708 0.323,0.167 10 false OFF 1.771,0.917 2.094,1.083 0.323,0.167 10 false OFF 0.188,0.969 1.198,1.635 1.01,0.667 10 false Leak Detection Pump 0.458,1.656 1.167,2.01 0.708,0.354 10 false Vent Valve 6.406,1.781 7.125,2.135 0.719,0.354 10 false OFF: Vent 4.625,1.563 5.406,1.927 0.781,0.365 10 false ON: Closed 0.167,2.042 1.208,2.375 1.042,0.333 10 false EVAP Pressure 0.375,2.375 0.938,2.708 0.563,0.333 10 false Positive 0.375,2.74 1.01,3.073 0.635,0.333 10 false Negative 4.917,2.875 5.667,3.156 0.75,0.281 10 false P0455 4.948,3.469 5.688,3.75 0.74,0.281 10 false P0456 4.01,3.479 4.573,3.76 0.563,0.281 10 false OK 0.094,0.052 3.667,0.469 3.573,0.417 12 false EVAP Pressure when EVAP System Leaks: 0.052,3.219 1.063,3.875 1.01,0.656 10 false First Reference Pressure 4.198,2 5.458,2.729 1.26,0.729 10 false [Second Reference Pressure] x 0.377 0.052,4.042 0.729,4.344 0.677,0.302 10 false Sequence 0.063,4.344 1.125,4.646 1.063,0.302 10 false Time (Seconds) 2.51,3.938 2.771,4.146 0.26,0.208 10 false A 3.135,3.927 3.396,4.135 0.26,0.208 10 false B 3.479,3.927 3.74,4.135 0.26,0.208 10 false C 4.583,3.927 4.844,4.135 0.26,0.208 10 false D 6.021,3.917 6.281,4.125 0.26,0.208 10 false E 2.438,4.188 2.708,4.521 0.271,0.333 10 false 300 3.104,4.188 3.375,4.521 0.271,0.333 10 false 40 3.448,4.188 3.719,4.521 0.271,0.333 10 false 12 4.521,4.188 4.792,4.521 0.271,0.333 10 false 900 5.99,4.177 6.26,4.51 0.271,0.333 10 false 40


CONFIRMATION DRIVING PATTERN

NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 5 steps performed automatically by the GTS. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F) and the coolant temperature below 45°C (113°F).



1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode.

7.

After the Evaporative System Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine / Utility / All Readiness.

8.

Input the DTC: P0455, P0456, P1451 or P2404.

9.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



10.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0455, P0456, P1451 or P2404 is output A
DTC P0455, P0456, P1451 or P2404 and other DTCs are output B



A

B