Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM J

FA20 ENGINE CONTROL  SFI SYSTEM  EVAP System  


RELATED DTCS

DTC No. Monitoring Item See page
P0441 Purge flow (Click here)
P0451 Canister pressure sensor (built into canister pump module) signal becomes fixed/flat (Click here)
P0452 Canister pressure sensor (built into canister pump module) voltage low
P0453 Canister pressure sensor (built into canister pump module) voltage high
P0455 EVAP gross leak (Click here)
P0456 EVAP small leak
P0458 Purge valve voltage low (Click here)
P0459 Purge valve voltage high
P1449 Air filter clogged (built into canister pump module) (Click here)
P1451 Pipe clogged (Click here)
P2404
·

Reference orifice high-flow (built into canister pump module)

·

Reference orifice low-flow (built into canister pump module)


P2401 Leak detection pump stuck OFF (built into canister pump module) (Click here)
P2402 Leak detection pump stuck ON (built into canister pump module)
P2419 Vent valve stuck closed (built into canister pump module)
P2420 Vent valve stuck open (vent) (built into canister pump module)
P2610 Soak timer (built into ECM) (Click here)

If any EVAP system DTCs are stored, the malfunctioning area can be determined using the table below.

A281938E03
0.115,0.521 1.5,0.823 1.385,0.302 10 false Malfunctioning Areas 2.677,0.333 3.083,0.656 0.406,0.323 10 false DTCs 3.323,0.406 3.76,0.625 0.438,0.219 10 false P0441 3.792,0.406 4.229,0.625 0.438,0.219 10 false P0451 4.26,0.406 4.698,0.625 0.438,0.219 10 false P0452 4.729,0.406 5.167,0.625 0.438,0.219 10 false P0453 5.208,0.406 5.646,0.625 0.438,0.219 10 false P0455 5.688,0.406 6.125,0.625 0.438,0.219 10 false P0456 6.156,0.406 6.594,0.625 0.438,0.219 10 false P0458 6.635,0.406 7.073,0.625 0.438,0.219 10 false P0459 0.115,1.74 2.313,2.083 2.198,0.344 10 false Purge valve low output 0.115,0.906 2.313,1.25 2.198,0.344 10 false Purge valve stuck open 0.115,1.333 2.313,1.677 2.198,0.344 10 false Purge valve stuck closed 0.115,2.167 2.313,2.458 2.198,0.292 10 false Purge valve high output 0.115,3.021 2.448,3.344 2.333,0.323 10 false Canister pressure sensor low output 0.115,2.604 2.448,2.927 2.333,0.323 10 false Canister pressure sensor signal fixed 0.115,3.458 2.448,3.802 2.333,0.344 10 false Canister pressure sensor high output 0.115,3.875 1.563,4.188 1.448,0.313 10 false Gross leak 0.115,4.313 1.563,4.615 1.448,0.302 10 false Small leak

A282300E03
0.104,0.542 1.49,0.844 1.385,0.302 10 false Malfunctioning Areas 2.521,0.333 3.01,0.656 0.49,0.323 10 false DTCs 3.323,0.49 3.76,0.708 0.438,0.219 10 false P1449 3.865,0.5 4.302,0.719 0.438,0.219 10 false P1451 6.031,0.5 6.469,0.729 0.438,0.229 10 false P2419 6.573,0.5 7.01,0.729 0.438,0.229 10 false P2420 5.479,0.5 5.917,0.729 0.438,0.229 10 false P2404 4.396,0.5 4.833,0.708 0.438,0.208 10 false P2401 4.938,0.5 5.375,0.708 0.438,0.208 10 false P2402 0.115,3.708 1.583,4.052 1.469,0.344 10 false Canister filter clogged 0.115,4.198 1.635,4.542 1.521,0.344 10 false Pipe clogged 0.115,0.99 1.813,1.313 1.698,0.323 10 false Reference orifice low-flow 0.115,1.427 1.813,1.75 1.698,0.323 10 false Reference orifice high-flow 0.115,1.896 2.198,2.208 2.083,0.313 10 false Leak detection pump stuck OFF 0.115,2.333 2.198,2.646 2.083,0.313 10 false Leak detection pump stuck ON 0.115,2.802 2.229,3.125 2.115,0.323 10 false Vent valve stuck closed 0.115,3.271 2.229,3.594 2.115,0.323 10 false Vent valve stuck open

DESCRIPTION

A281937E03
3.813,1.188 4.281,0.719 4.281,0.719 4.906,0.719 true 4.813,3.396 5.281,2.927 5.281,2.927 5.906,2.927 true 5.26,5.552 5.417,5.688 5.417,5.688 6.042,5.688 true 4.385,4.458 4.854,3.99 4.854,3.99 5.854,3.99 true 5.594,5.365 6.063,4.896 6.063,4.896 6.385,4.896 true 2.938,4.854 2.281,5.51 2.281,5.51 1.948,5.51 true 3.646,1.344 4.885,2.24 4.885,2.24 5.51,2.24 true 3.323,1.208 2.552,0.49 2.552,0.49 1.719,0.49 true 2.667,2.25 1.885,1.531 1.885,1.531 1.063,1.531 false 0.281,0.177 0.521,0.354 0.24,0.177 10 false *a 4.969,0.625 5.188,0.781 0.219,0.156 10 false *1 1.51,0.396 1.708,0.594 0.198,0.198 10 false *2 5.573,2.156 5.813,2.385 0.24,0.229 10 false *3 5.969,2.854 6.208,3.083 0.24,0.229 10 false *4 5.906,3.896 6.146,4.125 0.24,0.229 10 false *5 6.104,5.604 6.344,5.802 0.24,0.198 10 false *7 1.75,5.427 1.99,5.625 0.24,0.198 10 false *8 6.438,4.823 6.677,5.021 0.24,0.198 10 false *6 0.813,1.458 1.031,1.625 0.219,0.167 10 false *9

Text in Illustration
*1 Purge Valve *2 EVAP Hose (to Intake Manifold)
*3 EVAP Hose (from Charcoal Canister Assembly) *4 Fuel Tank
*5 Canister Pump Module
- Canister Pressure Sensor
- Leak Detection Pump
- Vent Valve
- Canister filter
*6 Fuel Tank Cap Assembly
*7 Air Inlet Port *8 Charcoal Canister Assembly
*9 Purge Line - -
*a Location of EVAP (Evaporative Emission) System - -

HINT:

The canister pressure sensor, the canister filter, the leak detection pump and the vent valve are built into the canister pump module.


A281934E03
2.448,0.167 3.323,0.167 3.323,0.167 3.552,0.396 true 4.781,0.771 4.656,0.406 4.656,0.406 4.49,0.406 true 5.146,0.719 5.26,0.354 5.26,0.354 5.438,0.354 true 4.323,1.094 4.896,1.448 4.896,1.448 5.375,1.448 true 4.927,2.125 4.792,2.125 4.792,2.125 4.375,2.688 true 5.292,2.25 5.156,2.25 5.156,2.25 4.771,2.583 false 6.76,2.979 6.458,2.979 6.458,2.979 5.99,2.281 true 3.125,3.625 3.573,3.625 3.573,3.625 3.948,2.99 true 3.115,2.458 3.438,2.458 3.438,2.458 3.656,2.177 true 1.969,3.25 2.25,3.25 2.25,3.25 2.573,2.719 true 1.177,2.781 1.469,2.781 1.469,2.781 1.781,2.24 true 1.01,1.74 0.729,1.74 0.729,1.74 0.417,1.208 true 1.26,1.49 0.979,1.49 0.979,1.49 0.552,1.063 true 0.115,0.073 0.385,0.281 0.271,0.208 10 false *a 5.479,0.281 5.708,0.458 0.229,0.177 10 false *1 4.281,0.333 4.51,0.51 0.229,0.177 10 false *2 5.427,1.365 5.656,1.542 0.229,0.177 10 false *3 2.927,2.396 3.156,2.573 0.229,0.177 10 false *8 1.76,3.177 1.99,3.354 0.229,0.177 10 false *9 0.896,2.719 1.198,2.896 0.302,0.177 10 false *10 1.052,1.646 1.354,1.823 0.302,0.177 10 false *11 1.313,1.396 1.615,1.573 0.302,0.177 10 false *12 2.177,0.115 2.479,0.292 0.302,0.177 10 false *13 4.948,2.042 5.177,2.219 0.229,0.177 10 false *4 5.354,2.177 5.583,2.354 0.229,0.177 10 false *5 6.802,2.917 7.031,3.094 0.229,0.177 10 false *6 2.927,3.542 3.156,3.719 0.229,0.177 10 false *7

Text in Illustration
*1 Intake Manifold *2 Throttle Valve
*3 Purge Valve *4 Cut-off Valve
*5 Fuel Tank *6 Fuel Tank Cap Assembly
*7 Fuel Tank Vent Valve *8 Charcoal Canister Assembly (Charcoal Filter)
*9 Canister Filter *10 Canister Pump Module
*11 ECM *12 Soak Timer
*13 Air Cleaner - -
*a EVAP System Circuit - -

NOTICE:

In the EVAP system of this vehicle, turning ON the vent valve does not seal off the EVAP system. To check for leaks in the EVAP system, disconnect the air inlet drain hose and apply pressure from atmospheric side of the charcoal canister assembly.


While the engine is running, if a predetermined condition (closed-loop, etc.) is met, the purge valve is opened by the ECM and fuel vapors stored in the charcoal canister assembly are purged to the intake manifold. The ECM changes the duty cycle ratio of the purge valve to control purge flow volume.

The purge flow volume is also determined by the intake manifold pressure. Atmospheric pressure is allowed into the charcoal canister assembly through the vent valve to ensure that the purge flow is maintained when negative pressure (vacuum) is applied to the charcoal canister assembly.

The following two monitors run to confirm appropriate EVAP system operation.

Purge flow monitor


The purge flow monitor consists of the 2 monitors. The 1st monitor is conducted every time and the 2nd monitor is activated if necessary.

·

The 1st monitor

While the engine is running and the purge valve (Vacuum Switching Valve) is on (open), the ECM monitors the purge flow by measuring the EVAP pressure change. If the variation in the pressure is less than threshold, the ECM begins the 2nd monitor.

·

The 2nd monitor

The vent valve is turned ON (closed) and the EVAP pressure is then measured. If the variation in the pressure is less than threshold, the ECM interprets this as the purge valve being stuck closed, and illuminates the MIL and stores DTC P0441 (2 trip detection logic).



Atmospheric pressure check:

In order to ensure reliable malfunction detection, the variation between the atmospheric pressures, before and after of the purge flow monitor, is measured by the ECM.



A281932E03
5.927,1.49 5.74,1.49 5.74,1.49 5.521,1.042 true 3.885,3.177 3.698,3.177 3.698,3.177 3.479,2.729 true 3.979,2.552 4.156,2.552 4.156,2.552 4.333,1.948 true 0.469,2.021 0.656,2.021 0.656,2.021 0.865,1.167 true 0.25,1.74 0.438,1.74 0.438,1.74 0.615,1.24 false 3.802,2.135 3.333,2.135 3.333,2.135 3.031,1.927 true 2.083,3.573 2.26,3.573 2.26,3.573 2.656,2.708 true 1.667,3.323 1.844,3.323 1.844,3.323 2.302,2.323 true 1.052,3.083 1.229,3.083 1.229,3.083 1.688,2.479 false 0.792,2.542 0.979,2.542 0.979,2.542 1.844,1.802 true 5.823,1.979 6.01,1.979 6.01,1.979 6.583,1.802 true 5.583,3.531 5.396,3.531 5.396,3.531 5.094,3.031 true 0.115,0.083 0.333,0.24 0.219,0.156 10 false *a 6.583,0.604 6.802,0.76 0.219,0.156 10 false *b 0.052,1.656 0.26,1.854 0.208,0.198 10 false *1 0.271,1.927 0.479,2.125 0.208,0.198 10 false *2 5.969,1.385 6.177,1.583 0.208,0.198 10 false *3 5.635,1.896 5.844,2.094 0.208,0.198 10 false *4 5.625,3.458 5.844,3.646 0.219,0.188 10 false *5 3.927,3.115 4.146,3.302 0.219,0.188 10 false *6 1.885,3.479 2.104,3.667 0.219,0.188 10 false *7 1.458,3.25 1.677,3.438 0.219,0.188 10 false *8 3.781,2.49 4,2.677 0.219,0.188 10 false *9 0.521,2.458 0.792,2.646 0.271,0.188 10 false *12 3.833,2.042 4.104,2.229 0.271,0.188 10 false *10 0.792,3.01 1.063,3.198 0.271,0.188 10 false *11

Text in Illustration
*1 ECM *2 Soak Timer
*3 Purge Valve (on) *4 Fuel Tank Cap Assembly
*5 Fuel Tank *6 Canister Filter
*7 Leak Detection Pump (off) *8 Canister Pressure Sensor
*9 Charcoal Canister Assembly *10 Vent Valve (off)
*11 Canister Pump Module *12 Reference Orifice (0.02 inch)
*a EVAP Purge Flow *b to Intake Manifold

Component Operation
Charcoal Canister Assembly Contains activated charcoal to absorb EVAP (Evaporative Emissions) generated in fuel tank.
Cut-off valve Located in fuel tank. Valve closes by its own weight when vehicle overturns to prevent fuel from spilling out.
Purge valve (Vacuum Switching Valve) Opens or closes line between charcoal canister assembly and intake manifold. ECM uses purge valve to control EVAP purge flow. In order to discharge EVAP absorbed by charcoal canister assembly to intake manifold, ECM opens purge valve. EVAP discharge volume to intake manifold controlled by purge valve duty cycle (current-carrying time). (Open: on, Close: off)
Fuel Tank Vent Valve Located in the fuel tank. Passes evaporative emissions occurring during fueling to the charcoal canister assembly. Additionally, this mechanism also detects when the fuel tank is full.
Soak timer Built into ECM. To ensure accurate EVAP monitor, measures 5 hours (+/-15 min) after ignition switch is turned off. This allows fuel to cool down, stabilizing EVAP pressure. When approximately 5 hours elapsed, ECM activates (refer to fig. 3).
Canister pump module Consists of (a) to (d) below. Canister pump module cannot be disassembled.
(a) Vent valve Vents and closes EVAP system. When ECM turns valve on, EVAP system is closed. When ECM turns valve off, EVAP system is vented. Negative pressure (vacuum) is created in EVAP system to check for EVAP leaks by closing purge valve, turning on vent valve (closing it) and operating leak detection pump (refer to fig. 1).
(b) Canister pressure sensor Indicates pressure as voltages. ECM supplies regulated 5 V to pressure sensor, and uses feedback from sensor to monitor EVAP system pressure (refer to fig. 2).
(c) Leak detection pump Creates negative pressure (vacuum) in EVAP system for leak check.
(d) Reference orifice Has opening with 0.02 inch diameter. Vacuum is produced through orifice by closing purge valve, turning off vent valve and operating leak detection pump, to monitor reference pressure. Reference pressure indicates a small leak of EVAP.

A207995E25
3.198,1.75 2.656,2.844 true 5.333,1.823 4.896,2.792 true 6.24,1.76 5.958,2.823 true 2.813,1.865 2.813,2.135 2.813,2.135 1.563,2.823 true 1.26,0.948 2.177,1.406 true 2.323,2.198 1.354,2.292 true 0.208,0.125 0.427,0.354 0.219,0.229 10 false *a 1.521,1.469 1.698,1.635 0.177,0.167 10 false *1 1.354,2.802 1.583,2.99 0.229,0.188 10 false *3 1.135,2.208 1.323,2.438 0.188,0.229 10 false *2 4.063,0.094 4.323,0.26 0.26,0.167 10 false : *b 5.698,0.479 5.896,0.646 0.198,0.167 10 false *d 2.531,2.875 2.771,3.229 0.24,0.354 10 false *g 3.885,1.313 4.125,1.51 0.24,0.198 10 false *f 5.885,2.885 6.146,3.052 0.26,0.167 10 false *i 2.688,0.51 2.854,0.677 0.167,0.167 10 false *c 4.813,2.823 5.052,2.979 0.24,0.156 10 false *h 1.042,0.844 1.24,1.01 0.198,0.167 10 false *e

Text in Illustration
*1 Canister *2 Reference Orifice (0.02 Inch)
*3 Canister Pressure Sensor - -
*a Canister Pump Module (fig. 1) *b Airflow
*c Condition: Purge Flow *d Condition: Leak Check
*e Vent Valve: off (vent) *f to Canister Filter (Atmosphere)
*g Leak Detection Pump: off *h Vent Valve: on (closed)
*i Leak Detection Pump: on - -

A282306E09
4.49,3.323 5.063,2.688 false 4.531,1.417 5.104,0.781 false 0.115,0.135 3.177,0.542 3.063,0.406 10 false Canister Pressure Sensor Specification (fig.2) 1.292,0.75 2.313,1.063 1.021,0.313 10 false Output Voltage 1.729,1.458 2.24,1.635 0.51,0.177 10 false 4.095 V 1.729,3.021 2.24,3.198 0.51,0.177 10 false 0.973 V 1.885,1.917 2.26,2.094 0.375,0.177 10 false 4.0 V 1.885,2.625 2.26,2.802 0.375,0.177 10 false 1.5 V 2.948,3.469 3.156,3.667 0.208,0.198 10 false 61 2.948,3.635 3.333,3.833 0.385,0.198 10 false (458) 3.635,3.625 4.021,3.823 0.385,0.198 10 false (803) 3.615,3.458 3.917,3.656 0.302,0.198 10 false 107 4.354,3.448 5,3.625 0.646,0.177 10 false kPa (abs) 4.354,3.615 5.292,3.792 0.938,0.177 10 false [mmHg] (abs) 5.188,3.24 5.885,3.552 0.698,0.313 10 false Pressure 5.125,2.51 6.229,2.823 1.104,0.313 10 false Malfunction Area 5.156,0.646 6.26,0.958 1.104,0.313 10 false Malfunction Area 3.802,2.302 4.74,2.625 0.938,0.323 10 false Usable Range 1.521,4.125 2.24,4.458 0.719,0.333 10 false HINT: 1.521,4.396 6.229,4.729 4.708,0.333 10 false Standard atmospheric pressure is 101.3 kPa (abs) [760 mmHg (abs)]

A281933E03
3.781,0.844 4.021,1.021 0.24,0.177 9 false IG2 2.771,1.396 3.01,1.573 0.24,0.177 9 false IG2 1.823,3.031 2.573,3.219 0.75,0.188 9 false EFI (CTRL) 2.604,3.604 3.323,3.781 0.719,0.177 10 false EFI MAIN1 4.052,3.156 4.583,3.344 0.531,0.188 10 false SSHUT 4.219,2.49 4.573,2.677 0.354,0.188 10 false +B2 4.302,2.156 4.573,2.344 0.271,0.188 10 false +B 4.156,0.604 4.573,0.771 0.417,0.167 10 false IGSW 0.531,0.698 1.344,1.042 0.813,0.344 9 false from Battery 0.583,2.865 1.396,3.208 0.813,0.344 9 false from Battery 1.385,1.844 2.656,2.24 1.271,0.396 9 false from Ignition Switch 5.365,3.99 5.74,4.292 0.375,0.302 9 false ECM 4.813,2.292 5.49,2.813 0.677,0.521 9 false Power Source IC 4.792,3.115 5.583,3.635 0.792,0.521 9 false MAIN Relay Control IC 4.813,0.969 5.573,1.51 0.76,0.542 10 false Soak Timer IC 0.146,0.146 0.896,0.521 0.75,0.375 10 false fig. 3

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The GTS is required to conduct the following diagnostic troubleshooting procedure.



HINT:
·

Using the GTS monitor results enables the EVAP (Evaporative Emission) system to be confirmed.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



CONFIRMATION DRIVING PATTERN

HINT:

After a repair, check Monitor Status by performing the Key-Off Monitor Confirmation and Purge Flow Monitor Confirmation described below.


KEY-OFF MONITOR CONFIRMATION


a.

Preconditions

The monitor will not run unless:

·

The vehicle has been driven at 48 km/h (30 mph) or more for a total of 10 minutes or more.

·

The fuel tank is less than 90% full.

·

The engine coolant temperature is between 5°C and 45°C (41°F and 113°F).

·

The intake air temperature is between 5°C and 50°C (41°F and 122°F).

·

The vehicle remains stationary (the vehicle speed is 0 km/h [0 mph]).



b.

Monitor Conditions

1.

Allow the engine to idle for at least 5 minutes.

2.

Turn the ignition switch off and wait for 6 hours (8 or 10.5 hours).

HINT:

Do not start the engine until checking Monitor Status. If the engine is started, the steps described above must be repeated.




c.

Monitor Status

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine / Monitor / Current Monitor.

5.

Check the Monitor Status displayed on the GTS.

HINT:

If Incomplete is displayed, the monitor did not complete. Make sure that the preconditions have been met, and perform the Monitor Conditions again.





PURGE FLOW MONITOR CONFIRMATION (P0441)


HINT:

Perform this monitor confirmation after the Key-Off Monitor Confirmation shows Complete.


a.

Preconditions

The monitor will not run unless:

·

The vehicle has been driven at 60 km/h (40mph) or more for 10 minutes or more.

·

The engine coolant temperature is 4.4°C (40°F) or higher.

·

The intake air temperature is 4.4°C (40°F) or higher.



b.

Monitor Conditions

1.

Release the pressure from the fuel tank by removing and reinstalling the fuel tank cap assembly.

2.

Warm the engine up until the engine coolant temperature reaches more than 75°C (167°F).

3.

Increase the engine speed to 3000 rpm once.

4.

Allow the engine to idle and turn the A/C switch on for 1 minute.



c.

Monitor Conditions

1.

Turn the ignition switch off (if ON or if the engine is running).

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON.

4.

Turn the GTS on.

5.

Enter the following menus: Powertrain / Engine / Monitor / Current Monitor.

6.

Check the Monitor Status displayed on the GTS.

HINT:

If Incomplete is displayed, the monitor did not complete. Make sure that the preconditions have been met, and perform the Monitor Conditions again.





PROCEDURE

1.CONFIRM DTC
a.

Turn the ignition switch off and wait for 10 seconds.


b.

Turn the ignition switch to ON.


c.

Turn the ignition switch off and wait for 10 seconds.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm DTCs and freeze frame data.

If any EVAP system DTCs are stored, the malfunctioning area can be determined using the table below.

A281938E03
0.115,0.521 1.5,0.823 1.385,0.302 10 false Malfunctioning Areas 2.677,0.333 3.083,0.656 0.406,0.323 10 false DTCs 3.323,0.406 3.76,0.625 0.438,0.219 10 false P0441 3.792,0.406 4.229,0.625 0.438,0.219 10 false P0451 4.26,0.406 4.698,0.625 0.438,0.219 10 false P0452 4.729,0.406 5.167,0.625 0.438,0.219 10 false P0453 5.208,0.406 5.646,0.625 0.438,0.219 10 false P0455 5.688,0.406 6.125,0.625 0.438,0.219 10 false P0456 6.156,0.406 6.594,0.625 0.438,0.219 10 false P0458 6.635,0.406 7.073,0.625 0.438,0.219 10 false P0459 0.115,1.74 2.313,2.083 2.198,0.344 10 false Purge valve low output 0.115,0.906 2.313,1.25 2.198,0.344 10 false Purge valve stuck open 0.115,1.333 2.313,1.677 2.198,0.344 10 false Purge valve stuck closed 0.115,2.167 2.313,2.458 2.198,0.292 10 false Purge valve high output 0.115,3.021 2.448,3.344 2.333,0.323 10 false Canister pressure sensor low output 0.115,2.604 2.448,2.927 2.333,0.323 10 false Canister pressure sensor signal fixed 0.115,3.458 2.448,3.802 2.333,0.344 10 false Canister pressure sensor high output 0.115,3.875 1.563,4.188 1.448,0.313 10 false Gross leak 0.115,4.313 1.563,4.615 1.448,0.302 10 false Small leak

A282300E03
0.104,0.542 1.49,0.844 1.385,0.302 10 false Malfunctioning Areas 2.521,0.333 3.01,0.656 0.49,0.323 10 false DTCs 3.323,0.49 3.76,0.708 0.438,0.219 10 false P1449 3.865,0.5 4.302,0.719 0.438,0.219 10 false P1451 6.031,0.5 6.469,0.729 0.438,0.229 10 false P2419 6.573,0.5 7.01,0.729 0.438,0.229 10 false P2420 5.479,0.5 5.917,0.729 0.438,0.229 10 false P2404 4.396,0.5 4.833,0.708 0.438,0.208 10 false P2401 4.938,0.5 5.375,0.708 0.438,0.208 10 false P2402 0.115,3.708 1.583,4.052 1.469,0.344 10 false Canister filter clogged 0.115,4.198 1.635,4.542 1.521,0.344 10 false Pipe clogged 0.115,0.99 1.813,1.313 1.698,0.323 10 false Reference orifice low-flow 0.115,1.427 1.813,1.75 1.698,0.323 10 false Reference orifice high-flow 0.115,1.896 2.198,2.208 2.083,0.313 10 false Leak detection pump stuck OFF 0.115,2.333 2.198,2.646 2.083,0.313 10 false Leak detection pump stuck ON 0.115,2.802 2.229,3.125 2.115,0.323 10 false Vent valve stuck closed 0.115,3.271 2.229,3.594 2.115,0.323 10 false Vent valve stuck open



NEXT

2.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
2.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 5 steps performed automatically by the GTS. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F) and the coolant temperature below 45°C (113°F).



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode.


f.

After the EVAP SYSTEM CHECK is completed, check for pending DTCs by entering the following menus: Powertrain / Engine / Trouble Codes.

HINT:

If no pending DTCs are displayed, perform the Confirmation Driving Pattern. After this confirmation, check for pending DTCs. If no DTCs are displayed, the EVAP system is normal.




NEXT

3.PERFORM EVAP SYSTEM CHECK (MANUAL MODE)
3.PERFORM EVAP SYSTEM CHECK (MANUAL MODE)
A281935E06
0.813,0.646 1.167,0.823 0.354,0.177 10 false ECM 1.563,0.417 1.813,0.583 0.25,0.167 10 false ON 2.167,0.729 2.417,0.896 0.25,0.167 10 false ON 1.188,0.542 1.51,0.708 0.323,0.167 10 false OFF 1.771,0.896 2.094,1.063 0.323,0.167 10 false OFF 0.188,0.979 1.198,1.646 1.01,0.667 10 false Leak Detection Pump 0.448,1.646 1.156,2 0.708,0.354 10 false Vent Valve 6.406,1.771 7.125,2.125 0.719,0.354 10 false OFF: Vent 4.625,1.542 5.406,1.906 0.781,0.365 10 false ON: Closed 0.146,2.094 1.188,2.427 1.042,0.333 10 false EVAP Pressure 0.417,2.375 0.979,2.708 0.563,0.333 10 false Positive 0.406,2.75 1.042,3.083 0.635,0.333 10 false Negative 4.917,2.875 5.667,3.156 0.75,0.281 10 false Gross Leak 4.948,3.448 5.688,3.729 0.74,0.281 10 false Small Leak 4.188,3.698 4.75,3.979 0.563,0.281 10 false No Leak 0.094,0.073 1.833,0.49 1.74,0.417 12 false EVAP System Check: 0.073,3.219 1.083,3.875 1.01,0.656 10 false First Reference Pressure 4.198,2.021 5.448,2.75 1.25,0.729 10 false [Second Reference Pressure] x 0.377 0.375,3.958 0.74,4.26 0.365,0.302 10 false Step 0.073,4.219 1.135,4.521 1.063,0.302 10 false Time (Seconds) 0.292,4.458 1.073,4.813 0.781,0.354 10 false (Reference) 2.448,3.927 2.708,4.135 0.26,0.208 10 false 1/5 3.083,3.917 3.344,4.125 0.26,0.208 10 false 2/5 3.427,3.917 3.688,4.125 0.26,0.208 10 false 3/5 4.542,3.927 4.802,4.135 0.26,0.208 10 false 4/5 5.969,3.927 6.229,4.135 0.26,0.208 10 false 5/5 2.438,4.208 2.708,4.542 0.271,0.333 10 false 300 3.104,4.208 3.375,4.542 0.271,0.333 10 false 40 3.438,4.208 3.708,4.542 0.271,0.333 10 false 12 4.521,4.188 4.792,4.521 0.271,0.333 10 false 900 5.99,4.177 6.26,4.51 0.271,0.333 10 false 40

NOTICE:
·

In the Evaporative System Check (Manual Mode), the series of 5 Evaporative System Check steps are performed manually using the GTS.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F) and the coolant temperature below 45°C (113°F).



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Manual Mode.



NEXT

4.PERFORM EVAP SYSTEM CHECK (STEP 1/5)
4.PERFORM EVAP SYSTEM CHECK (STEP 1/5)
A397708E01
0.833,0.677 1.219,0.896 0.385,0.219 10 false ECM 1.208,0.583 1.667,0.781 0.458,0.198 10 false OFF 1.594,0.448 2.052,0.646 0.458,0.198 10 false ON 1.823,0.906 2.135,1.115 0.313,0.208 10 false OFF 2.177,0.75 2.635,0.948 0.458,0.198 10 false ON 0.188,1.01 1.177,1.438 0.99,0.427 10 false Leak Detection Pump 0.448,1.656 1.167,1.854 0.719,0.198 10 false Vent Valve 0.135,2.104 1.219,2.292 1.083,0.188 10 false EVAP Pressure 0.438,2.427 1.01,2.604 0.573,0.177 10 false Positive 0.406,2.833 0.979,3.01 0.573,0.177 10 false Negative 0.073,3.24 1.042,3.615 0.969,0.375 10 false First Reference Pressure 0.354,3.927 0.75,4.146 0.396,0.219 10 false Step 0.083,4.198 1.104,4.396 1.021,0.198 10 false Time (Seconds) 0.344,4.458 1.365,4.656 1.021,0.198 10 false (Reference) 2.448,4.167 2.844,4.385 0.396,0.219 10 false 300 2.458,3.927 2.854,4.146 0.396,0.219 10 false 1/5 3.052,2.271 5.219,2.542 2.167,0.271 10 false Leak Detection Pump Stuck OFF 4.917,1.563 5.698,1.76 0.781,0.198 10 false ON: Closed 6.396,1.781 7.083,1.979 0.688,0.198 10 false OFF: Vent

a.

Check the EVAP pressure in step 1/5.

Result
DTC
*
Result Suspected Trouble Area Proceed to
- Virtually no variation in EVAP pressure Not yet determined A
P2404 EVAP pressure is less than -0.224 kPa(gauge) [2 mmHg(gauge)] Leak detection pump stuck OFF B

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.



A

5.PERFORM EVAP SYSTEM CHECK (STEP 2/5)

B

9.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VACUUM PUMP)
5.PERFORM EVAP SYSTEM CHECK (STEP 2/5)
A282302E02
0.813,0.625 1.167,0.802 0.354,0.177 10 false ECM 1.563,0.427 1.813,0.594 0.25,0.167 10 false ON 2.167,0.74 2.417,0.906 0.25,0.167 10 false ON 1.188,0.552 1.51,0.719 0.323,0.167 10 false OFF 1.771,0.896 2.094,1.063 0.323,0.167 10 false OFF 0.188,1 1.198,1.667 1.01,0.667 10 false Leak Detection Pump 0.448,1.656 1.156,2.01 0.708,0.354 10 false Vent Valve 6.406,1.771 7.125,2.125 0.719,0.354 10 false OFF: Vent 4.625,1.542 5.406,1.906 0.781,0.365 10 false ON: Closed 0.146,2.125 1.188,2.458 1.042,0.333 10 false EVAP Pressure 0.344,2.406 0.906,2.74 0.563,0.333 10 false Positive 0.344,2.771 0.979,3.104 0.635,0.333 10 false Negative 0.052,3.188 1.063,3.844 1.01,0.656 10 false First Reference Pressure 0.313,3.896 0.677,4.198 0.365,0.302 10 false Step 0.073,4.146 1.135,4.448 1.063,0.302 10 false Time (Seconds) 0.229,4.417 1.01,4.771 0.781,0.354 10 false (Reference) 2.448,4.125 2.708,4.333 0.26,0.208 10 false 1/5 3.083,4.115 3.344,4.323 0.26,0.208 10 false 2/5 2.438,4.375 2.708,4.708 0.271,0.333 10 false 300 3.104,4.375 3.375,4.708 0.271,0.333 10 false 40 2.865,2.146 4.406,2.438 1.542,0.292 10 false Vent Valve Stuck Close 2.979,2.625 4.719,2.917 1.74,0.292 10 false Reference Orifice High-flow 3.083,3.333 4.823,3.625 1.74,0.292 10 false Reference Orifice Low-flow

a.

Check the EVAP pressure in steps 2/5.

Result
DTC* Result Suspected Trouble Area Proceed to
- Virtually no variation in EVAP pressure Not yet determined A
P2404 EVAP pressure fluctuates by more than +/- 0.3 kPa (gauge) [2 mmHg (gauge)]
·

Vent valve stuck close

·

Reference orifice high-flow

·

Reference orifice low-flow


B

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.

HINT:

The first reference pressure is the value determined in step 2/5.




A

6.PERFORM EVAP SYSTEM CHECK (STEP 3/5)

B

12.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
6.PERFORM EVAP SYSTEM CHECK (STEP 3/5)
A282303E02
0.813,0.625 1.167,0.802 0.354,0.177 10 false ECM 1.563,0.427 1.813,0.594 0.25,0.167 10 false ON 2.156,0.74 2.406,0.906 0.25,0.167 10 false ON 1.188,0.552 1.51,0.719 0.323,0.167 10 false OFF 1.771,0.906 2.094,1.073 0.323,0.167 10 false OFF 0.188,0.99 1.198,1.656 1.01,0.667 10 false Leak Detection Pump 0.448,1.656 1.156,2.01 0.708,0.354 10 false Vent Valve 6.406,1.76 7.125,2.115 0.719,0.354 10 false OFF: Vent 4.625,1.542 5.406,1.906 0.781,0.365 10 false ON: Closed 0.146,2.115 1.188,2.448 1.042,0.333 10 false EVAP Pressure 0.344,2.385 0.906,2.719 0.563,0.333 10 false Positive 0.344,2.75 0.979,3.083 0.635,0.333 10 false Negative 0.063,3.167 1.073,3.823 1.01,0.656 10 false First Reference Pressure 0.354,3.896 0.719,4.198 0.365,0.302 10 false Step 0.052,4.167 1.115,4.469 1.063,0.302 10 false Time (Seconds) 0.271,4.417 1.052,4.771 0.781,0.354 10 false (Reference) 3.417,4.115 3.677,4.323 0.26,0.208 10 false 3/5 3.438,4.385 3.708,4.719 0.271,0.333 10 false 12 3.885,3.958 5.354,4.25 1.469,0.292 10 false Vent Valve Stuck Open

a.

Check the EVAP pressure in step 3/5.

Result
DTC* Result Suspected Trouble Area Proceed to
- EVAP pressure increases by 0.2 kPa (gauge) [2 mmHg (gauge)] or more within 12 seconds. Not yet determined A
P2404
·

EVAP pressure increases by less than 0.2 kPa (gauge) [2 mmHg (gauge)] within 12 seconds.

·

Virtually no variation in EVAP pressure


Vent valve stuck open B

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.



A

7.PERFORM EVAP SYSTEM CHECK (STEP 4/5)

B

14.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR VENT VALVE)
7.PERFORM EVAP SYSTEM CHECK (STEP 4/5)
A282304E02
0.792,0.646 1.146,0.823 0.354,0.177 10 false ECM 1.563,0.417 1.813,0.583 0.25,0.167 10 false ON 2.156,0.75 2.406,0.917 0.25,0.167 10 false ON 1.188,0.542 1.51,0.708 0.323,0.167 10 false OFF 1.771,0.896 2.094,1.063 0.323,0.167 10 false OFF 0.167,0.969 1.177,1.635 1.01,0.667 10 false Leak Detection Pump 0.448,1.646 1.156,2 0.708,0.354 10 false Vent Valve 6.406,1.75 7.125,2.104 0.719,0.354 10 false OFF: Vent 4.615,1.552 5.396,1.917 0.781,0.365 10 false ON: Closed 0.146,2.156 1.188,2.49 1.042,0.333 10 false EVAP Pressure 0.344,2.385 0.906,2.719 0.563,0.333 10 false Positive 0.344,2.75 0.979,3.083 0.635,0.333 10 false Negative 0.063,3.115 1.073,3.771 1.01,0.656 10 false First Reference Pressure 0.354,3.854 0.719,4.156 0.365,0.302 10 false Step 0.063,4.177 1.125,4.479 1.063,0.302 10 false Time (Seconds) 0.271,4.458 1.052,4.813 0.781,0.354 10 false (Reference) 4.542,4.125 4.802,4.333 0.26,0.208 10 false 4/5 4.521,4.375 4.792,4.708 0.271,0.333 10 false 900 4.531,2.844 5.51,3.135 0.979,0.292 10 false Pipe Clogged

a.

Check the EVAP pressure in step 4/5.

Result
DTC* Result Suspected Trouble Area Proceed to
- EVAP pressure is more then -5 kPa (gauge) [-38 mmHg (gauge)] within 900 seconds Not yet determined A
P1451 EVAP pressure is reference pressure -0.9 kPa [-7 mmHg] less then -5 kPa (gauge) [-38 mmHg (gauge)] within 27 seconds Pipe clogged B

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.



A

8.PERFORM EVAP SYSTEM CHECK (STEP 5/5)

B

18.INSPECT EVAP HOSE (CHARCOAL CANISTER ASSEMBLY - CANISTER PUMP MODULE)
8.PERFORM EVAP SYSTEM CHECK (STEP 5/5)
A282305E02
0.813,0.635 1.167,0.813 0.354,0.177 10 false ECM 1.552,0.438 1.802,0.604 0.25,0.167 10 false ON 2.156,0.75 2.406,0.917 0.25,0.167 10 false ON 1.188,0.552 1.51,0.719 0.323,0.167 10 false OFF 1.771,0.906 2.094,1.073 0.323,0.167 10 false OFF 0.188,1 1.198,1.667 1.01,0.667 10 false Leak Detection Pump 0.448,1.677 1.156,2.031 0.708,0.354 10 false Vent Valve 6.406,1.771 7.125,2.125 0.719,0.354 10 false OFF: Vent 4.625,1.552 5.406,1.917 0.781,0.365 10 false ON: Closed 0.146,2.104 1.188,2.438 1.042,0.333 10 false EVAP Pressure 0.344,2.385 0.906,2.719 0.563,0.333 10 false Positive 0.344,2.771 0.979,3.104 0.635,0.333 10 false Negative 4.917,2.875 5.667,3.156 0.75,0.281 10 false Gross Leak 4.948,3.438 5.688,3.719 0.74,0.281 10 false Small Leak 0.052,3.188 1.063,3.844 1.01,0.656 10 false First Reference Pressure 4.198,2.021 5.5,2.75 1.302,0.729 10 false [Second Reference Pressure] x 0.377 0.354,3.885 0.719,4.188 0.365,0.302 10 false Step 0.063,4.198 1.125,4.5 1.063,0.302 10 false Time (Seconds) 0.271,4.448 1.052,4.802 0.781,0.354 10 false (Reference) 4.542,4.125 4.802,4.333 0.26,0.208 10 false 4/5 5.969,4.125 6.229,4.333 0.26,0.208 10 false 5/5 4.521,4.375 4.792,4.708 0.271,0.333 10 false 900 5.99,4.365 6.26,4.698 0.271,0.333 10 false 40

a.

Check the EVAP pressure in step 5/5.


b.

Compare the EVAP pressure in step 4/5 and the refeerence pressure (step 5/5).

Result
DTC* Result Suspected Trouble Area Proceed to
- EVAP pressure increases by 0.3 kPa (gauge) [2 mmHg (gauge)] or less within 40 seconds. Not yet determined
(no leakage from EVAP system)
A
P0455 EVAP pressure from step 4/5 higher than [reference pressure (step 4/5) x 0.377] EVAP gross leak B
P0456 EVAP pressure from step 4/5 higher than reference pressure (step D) EVAP small leak B

*: These DTCs are already present in the ECM when the vehicle arrives and are confirmed in the "Confirm DTC" procedure above.



A

27.REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS

B

20.CHECK FUEL TANK CAP ASSEMBLY
9.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VACUUM PUMP)
a.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Vacuum Pump.


b.
U146804E03
1.552,0.292 1.844,0.448 0.292,0.156 10 false G8 0.135,0.104 0.448,0.333 0.313,0.229 10 false *a

Measure the voltage according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Canister Pump Module)

Result
Tester Connection Condition Test Result Suspected Trouble Area Proceed to
G8-4 - Body ground Leak detection pump on and off
(Active Test ON and OFF)
Approximately 0 V when OFF and ON Power source wire harness of leak detection pump A
10 to 13 V when OFF and ON
·

Wire harness or connector between leak detection pump and ECM

·

ECM


B
10 to 13 V when OFF
Approximately 0 V when ON
Leak detection pump C



A

10.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR LEAK DETECTION PUMP)

B

11.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

C

28.REPLACE CANISTER PUMP MODULE
10.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR LEAK DETECTION PUMP)
a.

Turn the ignition switch off.


b.

Disconnect the canister pump module connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Result
Tester Connection Condition Test Result Suspected Trouble Area Proceed to
G8-3 - Body ground Ignition switch ON 11 to 14 V Canister pump module A
Below 1 V Wire harness or connector between canister pump module and battery B



A

28.REPLACE CANISTER PUMP MODULE

B

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the canister pump module connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-8 (MPMP) - G8-4 Always Below 1 Ω
A35-8 (MPMP) or G8-4 - Body ground Always 10 kΩ or higher


Result
Result Suspected Trouble Area Proceed to
OK ECM A
NG Wire harness or connector between ECM and canister pump module B



A

30.REPLACE ECM

B

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
a.

Turn the ignition switch off.


b.
U146804E03
1.552,0.292 1.844,0.448 0.292,0.156 10 false G8 0.135,0.104 0.448,0.333 0.313,0.229 10 false *a

Disconnect the canister pump module connector.

Text in Illustration
*a Component without harness connected
(Canister Pump Module)


c.

Apply the battery voltage to terminals G8-5 and G8-1 of the canister pump module.


d.

Touch the canister pump module to confirm the vent valve operation.

Result
Condition Tester Result Suspected Trouble Area Proceed to
Apply battery voltage to terminals G8-5 and G8-1 Operating
·

Wire harness or connector between vent valve and ECM

·

Leak detection pump performance deteriorates

·

Leak detection pump circuit malfunctioning (large resistance exists in the circuit)

·

ECM


A
Not operating Vent valve B



A

13.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

28.REPLACE CANISTER PUMP MODULE
13.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the canister pump module connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A35-1 (VPMP) - G8-1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A35-1 (VPMP) or G8-1 - Body ground Always 10 kΩ or higher


Result
Result Suspected Trouble Area Proceed to
OK ECM A
NG Wire harness or connector between ECM and canister pump module B


A

30.REPLACE ECM

B

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.INSPECT CANISTER PUMP MODULE (POWER SOURCE FOR VENT VALVE)
a.
U146804E03
1.552,0.292 1.844,0.448 0.292,0.156 10 false G8 0.135,0.104 0.448,0.333 0.313,0.229 10 false *a

Turn the ignition switch off.


Text in Illustration
*a Front view of wire harness connector
(to Canister Pump Module)

b.

Disconnect the canister pump module connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Result
Tester Connection Switch Condition Specified Condition Suspected Trouble Area Proceed to
G8-5 - Body ground Ignition switch ON 11 to 14 V
·

Wire harness or connector between vent valve and ECM

·

Vent valve

·

Charcoal canister assembly (charcoal filter inside canister) clogged

·

ECM


A
Below 1 V Power source wire harness of vent valve B



A

15.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)

B

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.INSPECT CANISTER PUMP MODULE (VENT VALVE OPERATION)
a.

Turn the ignition switch off.


b.
U146804E03
1.552,0.292 1.844,0.448 0.292,0.156 10 false G8 0.135,0.104 0.448,0.333 0.313,0.229 10 false *a

Disconnect the canister pump module connector.

Text in Illustration
*a Component without harness connected
(Canister Pump Module)


c.

Apply the battery voltage to terminals G8-5 and G8-1 of the pump module.


d.

Touch the canister pump module to confirm the vent valve operation.

Result
Condition Tester Result Suspected Trouble Area Proceed to
Apply battery voltage to terminals G8-5 and G8-1 Operating
·

Wire harness or connector between vent valve and ECM

·

Leak detection pump performance deteriorates

·

Leak detection pump circuit malfunctioning (large resistance exists in the circuit)

·

ECM


A
Not operating
·

Vent valve


B



A

16.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

28.REPLACE CANISTER PUMP MODULE
16.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the canister pump module connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Test Result Suspected Trouble Area Proceed to
A35-1 (VPMP) - G8-1 Always Below 1 Ω
·

Charcoal canister assembly (charcoal filter inside canister) clogged

·

ECM


A
10 kΩ or higher Wire harness or connector between ECM and charcoal canister assembly pump module B



A

17.INSPECT CHARCOAL CANISTER ASSEMBLY (CHARCOAL FILTER INSIDE CANISTER)

B

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
17.INSPECT CHARCOAL CANISTER ASSEMBLY (CHARCOAL FILTER INSIDE CANISTER)
a.

Check for filter blockage in the charcoal canister assembly (See page Engine / Hybrid System>FA20 EMISSION CONTROL>CANISTER>INSPECTION).

OK:

No blockages in the charcoal canister assembly.




OK

30.REPLACE ECM

NG

24.REPLACE CHARCOAL CANISTER ASSEMBLY
18.INSPECT EVAP HOSE (CHARCOAL CANISTER ASSEMBLY - CANISTER PUMP MODULE)
a.

Check for blockages in the EVAP purge line between the charcoal canister assembly and canister pump module.

OK:

No blockages in the EVAP purge line between the charcoal canister assembly and canister pump module.




OK

19.INSPECT EVAP HOSE (CHARCOAL CANISTER ASSEMBLY - FUEL TANK)

NG

26.REPAIR OR REPLACE EVAP PURGE LINE (PURGE VALVE - CANISTER)
19.INSPECT EVAP HOSE (CHARCOAL CANISTER ASSEMBLY - FUEL TANK)
a.

Check for blockages in the EVAP purge line between the charcoal canister assembly and fuel tank.

OK:

No blockages in the EVAP purge line between the charcoal canister assembly and fuel tank.




OK

24.REPLACE CHARCOAL CANISTER ASSEMBLY

NG

26.REPAIR OR REPLACE EVAP PURGE LINE (PURGE VALVE - CANISTER)
20.CHECK FUEL TANK CAP ASSEMBLY
a.

Check that the fuel tank cap assembly is correctly installed and confirm that the fuel tank cap assembly meets OEM specifications.


b.

Tighten the fuel tank cap assembly firmly (only one click sound could be heard).

Result
Test Result Suspected Trouble Area Proceed to
fuel tank cap assembly correctly installed - A
fuel tank cap assembly loose
·

fuel tank cap assembly improperly installed

·

Defective fuel tank cap assembly

·

fuel tank cap assembly does not meet OEM specifications


B
Defective fuel tank cap assembly - B
No fuel tank cap assembly - C



A

21.LOCATE EVAP LEAK PART

B

22.CORRECTLY REINSTALL OR REPLACE FUEL TANK CAP ASSEMBLY

C

23.REPLACE FUEL TANK CAP ASSEMBLY
21.LOCATE EVAP LEAK PART
a.

Check for leakage from EVAP system (hose, disconnection, cracks, etc.).


b.

Repair or replace the leak point.



NEXT

29.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
22.CORRECTLY REINSTALL OR REPLACE FUEL TANK CAP ASSEMBLY
HINT:
·

When reinstalling the fuel tank cap assembly, tighten it firmly (only one click sound could be head).

·

When replacing the fuel tank cap assembly, use a fuel tank cap assembly that meets OEM specifications, and install it firmly.




NEXT

29.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
23.REPLACE FUEL TANK CAP ASSEMBLY
HINT:

When installing the fuel tank cap assembly, tighten it firmly (only one click sound could be head).



NEXT

29.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
24.REPLACE CHARCOAL CANISTER ASSEMBLY
a.

Replace the charcoal canister assembly (See page Engine / Hybrid System>FA20 EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing the charcoal canister assembly, check the canister pump module interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose.

·

Check for filter blockage in the canister filter. if the canister filter has blockages, replace the canister pump module.



A281929E03
2.344,5.271 3.104,5.271 3.104,5.271 3.563,3.115 true 3.469,0.635 4.031,0.635 4.031,0.635 4.875,1.563 true 5.333,4.833 4.917,4.833 4.917,4.833 4.021,3.333 true 4.969,5.531 4.552,5.531 4.552,5.531 3.948,3.99 true 0.958,2 1.458,2 1.458,2 2.198,2.76 true 2.146,5.208 2.385,5.385 0.24,0.177 10 false *1 3.25,0.563 3.49,0.74 0.24,0.177 10 false *2 5.625,2.177 5.865,2.354 0.24,0.177 10 false *a 3.083,1.188 3.323,1.365 0.24,0.177 10 false *a 5.396,4.76 5.625,4.948 0.229,0.188 10 false *3 5.042,5.469 5.271,5.656 0.229,0.188 10 false *5 0.719,1.917 0.917,2.198 0.198,0.281 10 false *4

Text in Illustration
*1 Fuel Tank Vent Hose *2 Air Inlet Port
*3 Drain Hose *4 Fuel Tank
*5 Charcoal Canister Assembly - -
*a Inspection Area
(check for disconnection and/or cracks)
- -



NEXT

29.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
25.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

29.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
26.REPAIR OR REPLACE EVAP PURGE LINE (PURGE VALVE - CANISTER)

NEXT

29.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
27.REPAIR OR REPLACE PARTS AND COMPONENTS INDICATED BY OUTPUT DTCS
a.

Repair the malfunctioning areas indicated by the DTCs that had been confirmed when the vehicle was brought in.



NEXT

29.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
28.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>FA20 EMISSION CONTROL>CANISTER>REMOVAL).



NEXT

29.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
29.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 5 steps performed automatically by the GTS. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not run the engine in this step.

·

When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F) and the coolant temperature below 45°C (113°F).



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode.


f.

After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine / Trouble Codes.

Result
Result Proceed to
EVAP system DTCs are output A
No DTCs output
(No pending DTCs output)
B



A

30.REPLACE ECM

B

END

30.REPLACE ECM

NEXT

31.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
31.PERFORM EVAP SYSTEM CHECK (AUTOMATIC MODE)
NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 5 steps performed automatically by the GTS. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not run the engine in this step.

·

When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F) and the coolant temperature below 45°C (113°F).



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode.


f.

After the Evaporative System Check is completed, check for pending DTCs by entering the following menus: Powertrain / Engine / Trouble Codes.

HINT:

If no pending DTCs are found, the repair has been successfully completed.




NEXT

END