Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DTC SUMMARY

DTC No. DTC Detection Condition Trouble Area
P2610 One of the following conditions is met (2 trip detection logic):
Timer diagnosis
·

[(Engine ECU counter - soak timer IC counter) / Engine ECU counter] is 0.24 or more.


Full count diagnosis
·

Soak timer IC counter is not 1023.


Timer diagnosis
·

The setting time written to the soak timer IC is different to the value read.

·

Full count diagnosis during wake-up.

·

When the engine ECU counter is 1.636 seconds or less, the soak timer IC counter is 1023.

·

When the engine ECU counter is 2.456 seconds or less, the soak timer IC counter is not 1023.


Wake-up diagnosis
·

The set wake-up count is different from the actual wake-up count


ECM

DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

MONITOR DESCRIPTION

1.

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

2.

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned ON.


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 minutes or more.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P2610.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


13.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (IN ADDITION TO DTC P2610)
2.CHECK WHETHER DTC OUTPUT RECURS (IN ADDITION TO DTC P2610)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and wait for 10 minutes or more.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


j.

If no pending DTC is output, the repair has been successfully completed.



NEXT

END