Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › IGNITION COIL AND SPARK PLUG
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297479 IGNITION COIL AND SPARK PLUG A

FA20 ENGINE CONTROL  IGNITION COIL AND SPARK PLUG  REMOVAL  


PROCEDURE

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53608 3.REMOVE FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607 4.REMOVE FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY RH

Hide 5.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 82121 6.DISCONNECT ENGINE WIRE

a.
A276559

Disengage the 4 clamps, and disconnect the engine wire.


b.
A276560

Disengage the 3 clamps and bolt, and disconnect the engine wire.


Hide 31484A 7.REMOVE CLUTCH FLEXIBLE HOSE BRACKET (for RHD with Manual Transmission)

a.
A281340

Remove the clip, and disconnect the clutch flexible tube.


b.
A281341

remove the bolt, and disconnect the clutch flexible hose bracket.


Hide 10.SET SST

a.
A277903

Tie the front exhaust pipe sub-assembly onto the front suspension cross member sub-assembly using rope.

HINT:

This operation is necessary in order to prevent the front exhaust pipe sub-assembly from falling off.



b.
A276558

Remove the 2 nuts.


c.

Install the engine hanger with the bolt. (See page Engine / Hybrid System>FA20 (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL)

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


d.

Hoist the engine assembly up with an engine sling device and a mini crane.


e.
A276566E02
1.073,1.406 1.771,1.948 1.771,1.948 2.51,1.365 true 1.635,1.969 1.927,2.146 0.292,0.177 10 false SST

Install the SST to between the engine mount and front.

SST
09250-53010  


Hide 23261A 11.REMOVE INJECTOR COVER (for LH Side)

a.
A276567

Disengage the clamp, and disconnect the fuel hoses.


b.
A276568

Remove the 2 bolts and injector cover.


Hide 19500 12.REMOVE IGNITION COIL ASSEMBLY (for Bank 2)

a.

Disconnect the 2 ignition coil connectors from the ignition coil assembly.

HINT:
A420838E01
1.104,0.802 1.198,0.438 1.198,0.438 1.323,0.438 true 1.385,0.354 1.771,0.698 0.385,0.344 10 false *a 2.094,0.969 2.479,1.313 0.385,0.344 10 false *b

If a spring is used on the connector, slide and then disconnect the connector using a clip remover or the like while pushing the spring as shown in the illustration.

Text in Illustration
*a Spring
*b Push



b.
A277901

Remove the 2 bolts and remove the 2 ignition coils.


Hide 19100P 13.REMOVE SPARK PLUG (for Bank 2)

a.
A280253

Remove the 2 spark plugs.


Hide 19500 15.REMOVE IGNITION COIL ASSEMBLY (for Bank 1)

a.

Disconnect the 2 ignition coil connectors from the ignition coil assembly.

HINT:
A420839E01
0.729,0.844 0.646,0.51 0.646,0.51 0.531,0.51 true 0.354,0.417 0.76,0.74 0.406,0.323 10 false *a 2.708,1.031 3.115,1.354 0.406,0.323 10 false *b

If a spring is used on the connector, slide and then disconnect the connector using a clip remover or the like while pushing the spring as shown in the illustration.

Text in Illustration
*a Spring
*b Push



b.
A277902

Remove the 2 bolts and remove the 2 ignition coils.


Hide 19100P 16.REMOVE SPARK PLUG (for Bank 1)

a.
A285176

Remove the 2 spark plugs.