53301
1.SET HOOD SUB-ASSEMBLY
Change the front hood stay position from A to B, and support the hood sub-assembly at position B.
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)
for HFC-134a (R134a):
(See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT)
for HFO-1234yf (R1234yf):
(See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT)
3. DISCHARGE FUEL SYSTEM PRESSURE
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
53608
5.REMOVE FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY LH
53607
6.REMOVE FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY RH
7.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
Disconnect the hose.
Remove the 2 bolts and disconnect the chamber.
Loosen the hose clamp and disconnect the No. 2 ventilation hose.
Disconnect the mass air flow meter connector.
Disengage the clamp and separate the wire harness from the air cleaner cap.
Loosen the hose clamp.
Remove the 3 bolts and air cleaner cap with air cleaner hose.
Remove the bolt and stay from the body.
8.DRAIN ENGINE OIL
9.DRAIN ENGINE COOLANT
16470
10.REMOVE RADIATOR RESERVE TANK ASSEMBLY
16502
11.REMOVE WATER FILLER SUB-ASSEMBLY
Remove the 2 bolts and disconnect the water filler sub-assembly.
Remove the 2 clamps and water filler sub-assembly.
89871
12.REMOVE INJECTOR DRIVER
13.DISCONNECT ENGINE WIRE (for RHD)
Fix the disconnected harness components with tape to keep them out of the way.
for Automatic Transmission:
Release the lock of connector (A) and disconnect the connector.
Disconnect the connector (B).
Disconnect the 2 wire harness clamps.
Slide the connector in the direction shown in the illustration, and disconnect the wire harness.
Remove the 2 bolts and wire harness bracket from the No. 2 engine hanger.
Release the lock of connector (A) and disconnect the connector.
Disconnect the connector (B).
Disconnect the wire harness clamp and wire harness from the No. 2 engine hanger.
Disconnect the 2 wire harness clamps.
Remove the 2 bolts and 2 wire harness clamp brackets.
Disconnect the 5 wire harness clamps.
Disconnect the terminal cap.
Remove the nut and disconnect the wire harness from terminal B.
Disconnect the generator connector and disengage the clamp.
14.DISCONNECT ENGINE WIRE (for LHD)
Fix the disconnected harness components with tape to keep them out of the way.
Remove the 2 bolts and wire harness clamp bracket from the No. 2 engine hanger.
Release the lock of connector (A) and disconnect the connector.
Disconnect the connector (B).
Disconnect the connector.
Disconnect the wire harness clamp and wire harness from the No. 2 engine hanger.
Disconnect the 3 wire harness clamps.
for Automatic Transmission:
Release the lock of connector (A) and disconnect the connector.
Disconnect the connector (B).
Slide the connector in the direction shown in the illustration, and disconnect the wire harness.
Disconnect the 3 wire harness clamps.
Remove the bolt and wire harness clamp bracket.
Disconnect the terminal cap.
Remove the nut and disconnect the wire harness from terminal B.
Disconnect the generator connector and disengage the clamp.
12601B
15.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Air Conditioning System)
44771
16.DISCONNECT VACUUM TUBE CONNECTOR HOSE (for Automatic Transmission)
for LHD:
Loosen the hose clamp and disconnect the vacuum tube connector hose.
Remove the 2 bolts and disconnect the vacuum tube connector hose.
for RHD:
Loosen the hose clamp and disconnect the union to check valve hose.
44771
17.DISCONNECT VACUUM TUBE CONNECTOR HOSE (for Manual Transmission)
Loosen the hose clamp and disconnect the union to check valve hose from the intake manifold.
| *A | for LHD |
| *B | for RHD |
17141
18.REMOVE EXHAUST MANIFOLD
17401
19.FIX FRONT EXHAUST PIPE SUB-ASSEMBLY (for Manual Transmission)
Tie the front exhaust pipe sub-assembly to the front cross member sub-assembly with rope.
20.DISCONNECT HEATER WATER HOSE
Loosen the 2 hose clamps and disconnect the 2 heater water hoses.
32943
21.DISCONNECT NO. 1 TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)
Loosen the clip and disconnect the No. 1 transmission oil cooler hose.
88704
22.REMOVE SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System)
Remove the bolt and disconnect the suction hose sub-assembly from the compressor assembly with pulley.
Remove the O-ring from the discharge hose sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
for LHD:
Remove the bolt and slide the hook connector.
Remove the nut and suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
for RHD:
Remove the bolt and slide the hook connector.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88711
23.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Air Conditioning System)
28100
24.REMOVE STARTER ASSEMBLY (for Automatic Transmission)
28100
25.REMOVE STARTER ASSEMBLY (for Manual Transmission)
32943C
26.DISCONNECT NO. 3 TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)
Loosen the clip and disconnect the No. 3 transmission oil cooler hose.
16572
27.DISCONNECT RADIATOR OUTLET HOSE
Loosen the clip and disconnect the radiator outlet hose.
28.DISCONNECT GROUNDED CABLE
Remove the 2 bolts and disconnect the 2 grounded cables.
51444A
29.REMOVE REAR ENGINE UNDER COVER LH (w/ Floor Under Cover)
Remove the 3 bolts and 8 clips, then remove the rear engine under cover LH.
48811
30.REMOVE FRONT STABILIZER BAR (for Automatic Transmission)
17401
31.FIX FRONT EXHAUST PIPE ASSEMBLY (for Automatic Transmission)
Tie the front exhaust pipe assembly to the front cross member sub-assembly with rope.
35000
32.SEPARATE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
Remove the 3 bolts and 2 nuts.
|
Bolt |
|
Nut |
In order to prevent dropping, do not remove bolt B.
30300
33.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
Remove the 3 bolts and 2 nuts.
|
Bolt |
|
Nut |
In order to prevent dropping, do not remove bolt B.
57104A
34.SEPARATE FRONT CROSS MEMBER SUB-ASSEMBLY
Remove the 2 nuts from the front cross member sub-assembly.
11361J
35.REMOVE FLYWHEEL HOUSING UNDER COVER
32101C
36.REMOVE DRIVE PLATE SETTING HEXAGON BOLT (for Automatic Transmission)
37.SEPARATE FUEL HOSE
for Clamp Type:
Put matchmarks on the fuel hoses and fuel pipes.
| *a | matchmark |
Remove the clamp and disconnect the fuel tube, No. 2 fuel tube and fuel tube from the fuel pipe.
for Metal Type:
Using SST, disconnect the fuel tube and No. 2 fuel tube from the fuel pipe (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).
Remove the clamp and disconnect the No. 2 fuel vapor feed hose from the fuel pipe.
38.INSTALL ENGINE HANGER
Install the engine hanger with the bolt, as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 Engine Hanger | 12281-38030 |
| Bolt | 90119-14120 |
Use an engine sling device and a mini crane to hold the engine.
39.SUPPORT TRANSMISSION ASSEMBLY
Support the transmission assembly clutch housing with a jack.
Support the transmission assembly until the installation of the engine assembly is completed.
12000
40.REMOVE ENGINE ASSEMBLY
Remove the bolt from the transmission assembly.
| *A | for Automatic Transmission |
| *B | for Manual Transmission |
Hoist the engine assembly up with an engine sling device and a mini crane.
32101
41.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
31210
42.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
31250
43.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
13405
44.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
19315
45.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
46.INSTALL ENGINE STAND
Set the engine on an engine stand.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
12311
47.REMOVE FRONT ENGINE MOUNTING BRACKET
Remove the 4 bolts and 2 front engine mounting brackets.