Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › TIMING CHAIN › from 2016.06
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297490 TIMING CHAIN A

FA20 ENGINE MECHANICAL  TIMING CHAIN  REMOVAL  


PROCEDURE

Hide 11302 1.REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

Hide 2.MAKE PAINT MARKS

HINT:

If the alignment marks are difficult to identify during the work, mark the alignment marks with paint at the positions shown in the illustration, for easier recognition.


A387941E01
5.365,0.625 6.49,0.448 true 1.281,0.76 0.365,0.49 true 0.542,2.229 0.292,1.365 true 0.323,3.375 0.542,2.708 true 0.844,4.281 1.438,4.094 true 5.073,3.74 5.813,3.948 true 6.135,3.385 6.438,2.563 true 6.458,2.146 6.792,1.354 true 2.99,0.948 3.948,0.302 true 3.094,1.083 3.969,0.958 true 0.135,1.208 0.615,1.521 0.479,0.313 10 false *a 0.167,3.354 0.646,3.667 0.479,0.313 10 false *a 6.792,1.198 7.115,1.521 0.323,0.323 10 false *a 6.552,0.323 6.875,0.646 0.323,0.323 10 false *b 5.885,3.896 6.208,4.219 0.323,0.323 10 false *b 0.656,4.208 0.979,4.531 0.323,0.323 10 false *b 0.188,0.396 0.51,0.719 0.323,0.323 10 false *b 3.99,0.188 4.313,0.51 0.323,0.323 10 false *d 4,0.854 4.323,1.177 0.323,0.323 10 false *c 6.031,3.396 6.354,3.719 0.323,0.323 10 false *a

Text in Illustration
*a Triangular Mark *b Engraved Line
*c Oval Mark *d Crankshaft Timing Gear key

Hide 13506 3.REMOVE CHAIN SUB-ASSEMBLY (for Bank 1)

CAUTION:

Do not remove the chain sub-assembly from bank 2 at the same time as the chain sub-assembly is being removed from bank 1. Otherwise, the camshaft on bank 2 may turn suddenly, which is dangerous.


a.
A334213

Temporarily install the crankshaft pulley spacer and crankshaft pulley.


b.
A334218E03
0.469,0.792 1.208,0.25 1.208,0.25 0.458,1.083 true 0.854,2.563 0.396,2.938 false 1.635,2.479 1.031,2.625 false 2.458,0.917 1.906,0.229 false 2.854,1.292 2.854,1.885 true 0.24,2.885 0.448,3.094 0.208,0.208 10 false *c 1.229,0.104 1.438,0.313 0.208,0.208 10 false *a 2.719,1.927 3.083,2.156 0.365,0.229 10 false SST 0.938,3.063 1.302,3.271 0.365,0.208 10 false 10° 1.75,0.073 1.99,0.281 0.24,0.208 10 false *b 1.667,2.344 1.875,2.552 0.208,0.208 10 false *a

Using SST, turn the crankshaft pulley clockwise until the alignment marks on the camshaft timing intake gear assembly RH and the camshaft timing exhaust gear assembly RH, and the crankshaft pulley pin hole are aligned at the positions shown in the illustration.

SST
09960-10010  (09962-01000, 09963-01000)

Text in Illustration
*a Alignment Mark
*b Crankshaft Pulley Pin Hole
*c Crankshaft Timing Gear key

HINT:

At this time, the alignment mark on the crankshaft timing gear or sprocket and the crankshaft timing gear key are at the positions shown in the illustration.



c.

Remove the crankshaft pulley and crankshaft pulley spacer.


d.
A279526

Push down the chain tensioner slipper and insert a 2.5 mm (0.098 in.) hexagonal wrench through the stopper plate into the No. 1 chain tensioner assembly.


e.
A279527

Remove the 2 bolts and No. 1 chain tensioner assembly.


f.

Remove the chain tensioner slipper.


g.
A279528

Using a 5 mm hexagonal wrench, remove the bolt and No. 1 chain vibration damper.


h.

Remove the chain sub-assembly.

NOTICE:
·

With the chain sub-assembly removed, the valve heads may contact each other if the camshafts are turned, causing the valve stems to bend.

·

To avoid this, do not turn the intake camshaft RH and the exhaust camshaft RH more than the zero-lift range (the range where camshafts can be turned lightly by hand).



HINT:

Arrange the removed parts in the correct order.



Hide 13506 4.REMOVE CHAIN SUB-ASSEMBLY (for Bank 2)

a.

Temporarily install the crankshaft pulley spacer and crankshaft pulley.


b.

Using SST, turn the crankshaft pulley clockwise until the alignment marks on the camshaft timing intake gear assembly LH and the camshaft timing exhaust gear assembly LH, and the crankshaft pulley pin hole are aligned at the positions shown in the illustration.

SST
09960-10010  (09962-01000, 09963-01000)

A334219E03
1.313,0.375 1.5,0.198 false 1.354,1.563 2.021,1.052 false 4.5,2.479 4.781,2.115 false 4.271,1.615 4.542,1.615 false 3.229,1.083 2.969,1.979 true 5.49,0.573 5.313,0.802 5.313,0.802 5.781,1.021 true 5.115,0.708 5.344,0.906 0.229,0.198 10 false *a 1.188,1.5 1.417,1.698 0.229,0.198 10 false *b 4.365,2.469 4.594,2.667 0.229,0.198 10 false *c 1.49,0.083 1.719,0.281 0.229,0.198 10 false *d 2.813,2 3.188,2.198 0.375,0.198 10 false SST 4.552,1.521 4.781,1.719 0.229,0.198 10 false *d 5.083,0.51 5.396,0.708 0.313,0.198 10 false 25° 6.083,0.948 6.396,1.146 0.313,0.198 10 false 25°

Text in Illustration
*a Alignment Mark *b Crankshaft Pulley Pin Hole
*c Crankshaft Timing Gear key *d Cylinder Block Guide Pin

HINT:

At this time, the crankshaft timing gear key is at the position shown in the illustration.



c.

Remove the crankshaft pulley and crankshaft pulley spacer.


d.
A279530

Push the chain tensioner slipper and retain the plunger by inserting an approximately 1 mm (0.039 in.) wire through the stopper plate into the No. 2 chain tensioner assembly.


e.
A279531

Remove the 2 bolts and No. 2 chain tensioner assembly.


f.

Remove the chain tensioner slipper.


g.
A279532

Remove the O-ring from the cylinder block (bank 2).


h.
A279533

Using a 5 mm socket hexagon wrench, remove the bolt and No. 1 chain vibration damper.


i.
A334220E01
2.928,0.315 3.290,0.479 0.363,0.164 10 SST 2.895,0.451 2.67,0.692 false

While releasing the tension of chain sub-assembly using SST, remove the chain sub-assembly.

SST
09960-10010  (09962-01000, 09963-00700)

CAUTION:

Make sure to use SST. Never carry out the work using only your hands.


NOTICE:
·

With the chain sub-assembly removed, the valve heads may contact each other if the camshafts are turned, causing the valve stems to bend. To avoid this, do not turn the exhaust camshaft LH more than the zero-lift range (the range where the camshaft can be turned lightly by hand).

·

At this time, the No. 1 and No. 4 pistons are located near TDC. If the intake camshaft is turned, the valves may come into contact with the piston, causing the valve stems to bend. To avoid this, do not turn the intake camshaft LH.



HINT:

Arrange the removed parts in the correct order.