Home › Engine / Hybrid System › FA20 (LUBRICATION) › OIL PUMP
RM2090E _51 Engine / Hybrid System _060671 FA20 LUBRICATION _0297530 OIL PUMP A

FA20 LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 27020 3.REMOVE GENERATOR ASSEMBLY

Hide 16470 5.REMOVE RADIATOR RESERVE TANK ASSEMBLY

Hide 16173 10.REMOVE WATER PUMP PULLEY

Hide 13.DISCONNECT ENGINE WIRE

a.

Remove the 2 bolts and disconnect the 2 wire harness clamp brackets from the engine assembly.


b.
A281113

Remove the bolts and disconnect the wire harness clamp bracket from the engine assembly.


c.

Disconnect the camshaft position sensor connector.


d.
A281489

Disconnect the camshaft position sensor connector and 2 camshaft timing oil control valve connectors.


e.
A281490

Disconnect the camshaft position sensor connector and camshaft timing oil control valve connector.


f.

Disconnect the engine oil pressure switch connector and engine oil temperature connector.


g.

Disengage the clamp.


h.
A281491

Disconnect the camshaft position sensor connector and camshaft timing oil control valve connector.


Hide 11452 14.REMOVE OIL LEVEL DIPSTICK GUIDE

A276066

a.

Remove the oil level dipstick sub-assembly.


b.

Remove the bolt and oil level dipstick guide.


c.

Remove the O-ring from the oil level dipstick guide.


Hide 16604 15.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.
A276067

Remove the bolt, washer plate and No. 2 idler pulley sub-assembly.


Hide 16620 16.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A276068

Remove the 4 bolts and V-ribbed belt tensioner assembly.


Hide 16603 17.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A276069

Remove the bolt, washer plate and No. 1 idler pulley sub-assembly.


b.
A276070

Remove the bolt, washer plate and No. 1 idler pulley sub-assembly.


Hide 11302A 18.REMOVE TIMING CHAIN OR BELT COVER OIL SEAL

Hide 11302 19.REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

a.

Remove the 32 bolts.

A276071


b.

Using a screwdriver with its tip wrapped with protective tape, remove the timing chain or belt cover sub-assembly by prying between the timing chain or belt cover sub-assembly and cylinder head or cylinder block.

C257591E02
1.542,0.531 1.052,0.813 true 1.604,3.271 1.906,3.573 true 3.438,3.479 3.021,3.573 true 5.417,3.26 5,3.365 true 3.635,0.125 3.26,0.542 true 4.885,0.375 5.302,0.156 true 0.865,0.75 1.042,0.906 0.177,0.156 10 false *1 1.927,3.552 2.104,3.708 0.177,0.156 10 false *1 2.854,3.531 3.031,3.688 0.177,0.156 10 false *1 4.833,3.323 5.01,3.479 0.177,0.156 10 false *1 3.656,0.01 3.833,0.167 0.177,0.156 10 false *1 5.344,0.052 5.521,0.208 0.177,0.156 10 false *1

Text in Illustration
*1 Protective Tape - -

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head, cylinder block or chain cover.



c.

Remove the 4 O-rings.

A276072