Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › ENGINE UNIT › 2013.07–2016.06
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297496 ENGINE UNIT A

FA20 ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 11104F 1.INSTALL OIL SPACER LH

a.
A279591

Install the oil spacer LH with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 15678E 2.INSTALL OIL CONTROL VALVE FILTER (for Bank 2)

a.
A278751E02
2.719,1.188 2.875,1.385 0.156,0.198 10 false A 0.677,2.104 0.979,2.26 0.302,0.156 10 false A-A 2.094,1.177 2.25,1.375 0.156,0.198 10 false A 2.719,0.604 2.875,0.802 0.156,0.198 10 false A 2.073,0.615 2.229,0.813 0.156,0.198 10 false A 0.917,2.813 1.104,2.99 0.188,0.177 10 false *a

Install 2 new oil control valve filters to the camshaft housing sub-assembly LH as shown in the illustration.

Text in Illustration
*a 0 to 0.5 mm (0 to 0.0197 in.) from the face of the camshaft housing sub-assembly LH


Hide 001104 5.INSTALL HOLE PLUG (for Manual Transmission)

a.
A278792

Install a new gasket and the hole plug to the camshaft housing sub-assembly RH.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 15044 6.INSTALL CAMSHAFT OIL FEED PIPE SUB-ASSEMBLY (for Automatic Transmission)

a.

Temporarily install 2 new gaskets and the camshaft oil feed pipe sub-assembly with the bolt and 2 union bolts.


b.
A278793

Tighten the 2 union bolts to the specified torque.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


c.

Tighten the bolt to the specified torque.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 11103G 7.INSTALL OIL SPACER RH

a.
A279590

Install the oil spacer RH with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 15678D 8.INSTALL OIL CONTROL VALVE FILTER (for Bank 1)

a.
A278749E01
1.192,1.242 1.329,1.403 0.136,0.161 10 A 0.78,2.101 1.064,2.262 0.285,0.161 10 A-A 0.608,1.242 0.744,1.403 0.136,0.161 10 A 1.192,0.64 1.329,0.801 0.136,0.161 10 A 0.608,0.64 0.744,0.801 0.136,0.161 10 A 0.922,2.783 1.104,2.945 0.181,0.163 10 *a

Install 2 new oil control valve filters to the camshaft housing sub-assembly RH as shown in the illustration.

Text in Illustration
*a 0 to 0.5 mm (0 to 0.0197 in.) from the face of the camshaft housing sub-assembly RH


Hide 12101 11.INSTALL OIL PAN SUB-ASSEMBLY

a.
A280854E01
1.978,2.972 2.154,3.137 0.176,0.165 10 A

Install the 2 stud bolts to the oil pan sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Standard height (A):

70.0 mm (2.756 in.)



b.
A279598

Install the baffle plate to the oil pan sub-assembly with the 4 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


c.
A279595E03
1.646,2.531 1.427,2.969 false 1.042,1.563 1.125,1.802 1.125,1.802 1.177,1.552 false 1.313,3.01 1.521,3.188 0.208,0.177 10 false *d 1.125,2.385 1.333,2.563 0.208,0.177 10 false *b 1.042,1.813 1.25,1.99 0.208,0.177 10 false *a 1.552,1.99 1.792,2.167 0.24,0.177 10 false *c

Using a sealer gun, apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


Text in Illustration
*a Seal Packing
*b φ4.0 to 6.0 mm (0.158 to 0.236 in.)
*c 1.5 mm (0.059 in.)
*d Chamfer edge

NOTICE:
·

Clean and degrease the contact surface.

·

Install the oil pan sub-assembly within 5 minutes of applying seal packing.

·

Apply seal packing 1.5 mm (0.0591 in.) away from the outer side of the chamfer edge. However, it is allowed to apply the seal packing on the chamfer around the bolt hole.




d.
A278741

Install 3 new O-rings to the cylinder block.


e.
A279588E01
0.706,0.01 0.936,0.162 0.230,0.152 10 13 2.691,0.018 2.921,0.170 0.230,0.152 10 12 0.382,0.571 0.612,0.723 0.230,0.152 10 11 2.837,0.804 3.067,0.957 0.230,0.152 10 10 0.515,0.907 0.635,1.059 0.119,0.152 10 9 2.721,1.152 2.840,1.305 0.119,0.152 10 8 0.69,1.181 0.809,1.333 0.119,0.152 10 7 2.62,1.434 2.739,1.587 0.119,0.152 10 6 0.781,1.604 0.900,1.757 0.119,0.152 10 5 1.284,0.01 1.403,0.162 0.119,0.152 10 4 1.732,1.934 1.852,2.087 0.119,0.152 10 3 1.771,0.014 1.890,0.166 0.119,0.152 10 2 1.333,1.934 1.452,2.087 0.119,0.152 10 1

Tighten the 13 bolts in the order shown in the illustration to install the oil pan sub-assembly to the cylinder block.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

Text in Illustration
V100135

Bolt A
V100136

Bolt B

Length of bolt A:

25.0 mm (0.984 in.)


Length of bolt B:

75.0 mm (2.953 in.)


HINT:

After tightening the bolts, if the seal packing is squeezed out onto the seal surface of the chain cover, completely remove it.



Hide 15104 12.INSTALL OIL STRAINER SUB-ASSEMBLY

A278798

a.

Install a new O-ring.


b.

Install the oil strainer sub-assembly to the oil pan sub-assembly with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 12102A 13.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.
A279593

Install 2 new oil pan seal rings to the No. 2 oil pan sub-assembly.


b.
A279594E03
1.01,1.594 1.479,1.448 false 0.635,0.646 0.823,0.844 0.188,0.198 10 false *b 2.25,2.604 2.448,2.781 0.198,0.177 10 false *c 0.802,1.49 1,1.667 0.198,0.177 10 false *a

Using a sealer gun, apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


NOTICE:
·

Clean and degrease the contact surface.

·

Install the No. 2 oil pan sub-assembly within 5 minutes of applying seal packing.



Text in Illustration
*a Seal Packing
*b 9.5 mm (0.374 in.)
*c φ4.0 to 6.0 mm (0.158 to 0.236 in.)


c.
U146731E03
1.635,1.958 1.823,2.125 0.188,0.167 10 false 11 1.938,0.198 2.125,0.365 0.188,0.167 10 false 10 0.448,0.99 0.563,1.156 0.115,0.167 10 false 9 2.396,0.656 2.51,0.823 0.115,0.167 10 false 8 0.448,1.302 0.563,1.469 0.115,0.167 10 false 7 2.396,1.385 2.51,1.552 0.115,0.167 10 false 6 0.448,0.635 0.563,0.802 0.115,0.167 10 false 5 1.979,1.833 2.094,2 0.115,0.167 10 false 4 0.938,0.083 1.052,0.25 0.115,0.167 10 false 3 0.615,1.875 0.729,2.042 0.115,0.167 10 false 2 2.396,1.052 2.51,1.219 0.115,0.167 10 false 1

Tighten the 11 bolts in the order shown in the illustration to install the No. 2 oil pan sub-assembly.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


d.

Install a new gasket and the drain plug.

Torque:
42 N*m (425 kgf*cm, 31 ft.*lbf)


Hide 14.INSTALL NO. 2 ENGINE HANGER

a.
A279574

Install the No. 2 engine hanger to the cylinder block (for bank 1) with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


Hide 11104A 17.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A278738

Apply engine oil to the 8 valve adjusting shims and 8 roller rocker arm pivots, and then install them to the cylinder head sub-assembly LH.

HINT:

Be sure to install the removed parts in their original locations.



b.
A278737

Apply engine oil to 2 new O-rings and the 8 No. 1 valve rocker arm sub-assemblies, and then install them to the cylinder head sub-assembly LH.


c.

Using a sealer gun, apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


U146819E01
0.747,1.917 1.040,2.078 0.293,0.161 10 B-B 0.747,0.796 1.040,0.957 0.293,0.161 10 A-A 1.224,2.192 1.401,2.359 0.177,0.167 10 *a 1.224,1.772 1.401,1.939 0.177,0.167 10 *d 1.925,1.604 2.102,1.771 0.177,0.167 10 *e 1.225,1.114 1.402,1.281 0.177,0.167 10 *a 1.225,0.693 1.402,0.861 0.177,0.167 10 *d 1.926,0.525 2.103,0.693 0.177,0.167 10 *c 1.676,0.814 1.383,1.151 false 4.532,1.336 4.743,1.539 0.211,0.202 10 *b 3.831,1.336 4.043,1.539 0.211,0.202 10 *b 4.268,1.84 4.532,1.466 false 4.862,1.963 4.995,2.114 0.133,0.151 10 A 3.828,2.196 3.961,2.347 0.133,0.151 10 B 4.853,2.275 4.986,2.426 0.133,0.151 10 A 4.184,2.511 4.317,2.662 0.133,0.151 10 B 3.912,2.369 4.081,2.533 0.169,0.164 10 *f 2.866,1.323 3.088,1.507 0.222,0.184 10 *f 1.685,1.894 1.392,2.231 false

Text in Illustration
*a Chamfer edge *b Range of B-B
*c within 1.0 mm (0.0394 in.) *d φ2.5 to 3.5 mm (0.098 to 0.138 in.)
*e -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) *f 18.0 mm (0.709 in.)

NOTICE:
·

Clean and degrease the contact surface.

·

Do not apply excessive seal packing.

·

Install the camshaft housing sub-assembly LH within 5 minutes of applying seal packing.

·

After tightening the bolts, if the seal packing is squeezed out onto the seal surface of the chain cover, completely remove it.




d.
U146818E03
0.385,1.75 0.5,1.927 0.115,0.177 10 false 8 3.281,0.271 3.396,0.448 0.115,0.177 10 false 9 3.198,1.656 3.313,1.833 0.115,0.177 10 false 7 0.167,0.083 0.281,0.26 0.115,0.177 10 false 6 3.24,0.969 3.354,1.146 0.115,0.177 10 false 5 0.51,1.063 0.625,1.24 0.115,0.177 10 false 4 2.125,1.51 2.24,1.688 0.115,0.177 10 false 3 2.271,0.052 2.385,0.229 0.115,0.177 10 false 2 2.125,0.688 2.24,0.865 0.115,0.177 10 false 1

Tighten the 9 bolts in the order shown in the illustration to install the camshaft housing sub-assembly LH.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

HINT:
A278759

Set the intake camshaft LH and the exhaust camshaft LH to the zero-lift position.



e.
U146820E01
2.152,0.743 2.281,0.905 0.130,0.162 10 3 2.3,0.067 2.429,0.229 0.130,0.162 10 2 2.129,1.586 2.258,1.748 0.130,0.162 10 1

Loosen the 3 bolts by 180° in the order shown in the illustration.


f.
U146821E01
2.136,1.58 2.266,1.742 0.130,0.162 10 3 2.293,0.049 2.423,0.211 0.130,0.162 10 2 2.13,0.745 2.260,0.907 0.130,0.162 10 1

Tighten the 3 bolts in the order shown in the illustration.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


g.
U146822E01
1.358,0.791 1.488,0.953 0.130,0.162 10 3 1.004,0.381 1.134,0.543 0.130,0.162 10 2 1.22,1.489 1.350,1.651 0.130,0.162 10 1

Loosen the 3 bolts by 180° in the order shown in the illustration.


h.
U146823E01
1.227,1.479 1.356,1.641 0.130,0.162 10 3 0.989,0.382 1.118,0.544 0.130,0.162 10 2 1.363,0.797 1.493,0.959 0.130,0.162 10 1

Tighten the 3 bolts in the order shown in the illustration.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


i.
U146824E01
3.119,0.68 3.249,0.842 0.130,0.162 10 3 3.172,0.02 3.301,0.182 0.130,0.162 10 2 3.061,1.41 3.190,1.572 0.130,0.162 10 1

Loosen the 3 bolts by 180° in the order shown in the illustration.


j.
U146825E01
3.09,1.378 3.220,1.540 0.130,0.162 10 3 3.172,0.024 3.302,0.186 0.130,0.162 10 2 3.149,0.727 3.278,0.889 0.130,0.162 10 1

Tighten the 3 bolts in the order shown in the illustration.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

HINT:

After tightening the bolts, if the seal packing is squeezed out onto the seal surface of the chain cover, completely remove it.



Hide 18.INSPECT VALVE CLEARANCE (for Bank 2)

NOTICE:

With the chain sub-assembly (for bank 2) removed, valve heads may contact each other if the camshafts are turned, causing the valve stems to bend. To avoid this, do not turn the intake camshaft LH and exhaust camshaft LH more than the zero-lift rang (The range where the camshafts can be turned lightly by hand).


a.

Using a feeler gauge, check the valve clearance between the cam base circle and the roller surface of the No. 1 valve rocker arm sub-assembly.

A281473

Standard valve clearance (cold):

0.10 to 0.15 mm (0.00394 to 0.00591 in.) for intake

0.20 to 0.24 mm (0.00787 to 0.00945 in.) for exhaust


HINT:
·

Set the intake camshaft LH and the exhaust camshaft LH to the zero-lift position.

·

If the clearance is not as specified, take notes of the value in order to adjust the valve clearance later on.




Hide 19.ADJUST VALVE CLEARANCE (for Bank 2)

a.

Remove the camshaft housing sub-assembly LH.


b.

Remove the No. 1 valve rocker arm sub-assemblies.


c.

Remove the valve adjusting shims.


d.
A281710

Using a micrometer, measure the thickness of the valve adjusting shims.


e.

Calculate the thickness of the valve adjusting shim so that the valve clearance comes within the specified values.

Intake side:

A = B + (C - 0.13 mm (0.00512 in.) x 1.54


Exhaust side:

A = B + (C - 0.22 mm (0.00866 in.) x 1.69


A:

Required valve adjusting shim thickness


B:

Removed valve adjusting shim thickness


C:

Measured valve clearance



f.

Apply engine oil to the inner face of the valve adjusting shims and install them to the valves.

NOTICE:

Check if the shims can be rotated smoothly on the valves.



g.

Install the No. 1 valve rocker arm sub-assemblies.


h.

Install the camshaft housing sub-assembly LH.


Hide 11202 20.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A279571E01
2.753,0.066 2.936,0.250 0.183,0.183 10 *a 3.115,0.753 3.115,0.166 3.115,0.166 2.964,0.166 false

Apply a light layer of engine oil to 2 new spark plug tube gaskets and install them to the spark plug tubes as shown in the illustration.

Text in Illustration
*a Spark plug tube edge


b.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly LH.


c.
A279572E03
0.698,1.917 0.865,2.156 0.865,2.156 0.698,2.375 false 0.698,0.792 0.854,1.021 0.854,1.021 0.698,1.229 false 0.698,2.469 0.917,2.833 false 2.188,0.583 2.354,1.01 false 2.49,2.167 2.781,2.385 false 0.063,2.396 0.188,2.552 0.125,0.156 10 false A 0.063,1.823 0.188,1.979 0.125,0.156 10 false A 0.063,1.229 0.188,1.385 0.125,0.156 10 false A 2.958,0.25 3.083,0.406 0.125,0.156 10 false B 1.781,0.26 1.906,0.417 0.125,0.156 10 false A 0.063,0.698 0.188,0.854 0.125,0.156 10 false A 0.938,2.802 1.125,2.969 0.188,0.167 10 false *b 0.875,2.052 1.063,2.219 0.188,0.167 10 false *a 0.865,0.917 1.052,1.083 0.188,0.167 10 false *a 2.302,1.052 2.49,1.219 0.188,0.167 10 false *a 3.25,2.25 3.375,2.406 0.125,0.156 10 false C 3.021,2.698 3.146,2.854 0.125,0.156 10 false A 2.292,2.042 2.479,2.208 0.188,0.167 10 false *a

Using a sealer gun, apply seal packing to the mating surface of cylinder head cover sub-assembly LH as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


Area Application Length
A 10.0 mm (0.394 in.) or more
B 18.8 mm (0.740 in.) or more
C 63.0 mm (2.480 in.) or more

Text in Illustration
*a Arch starting point
*b φ2,0 to 4.0 mm (0.079 to 0.158 in.)


d.
U146738E03
0.917,1.979 1.042,2.146 0.125,0.167 10 false 7 2.656,0.063 2.781,0.229 0.125,0.167 10 false 8 1.656,1.979 1.781,2.146 0.125,0.167 10 false 4 1.833,0.052 1.958,0.219 0.125,0.167 10 false 3 2.885,1.104 3.01,1.271 0.125,0.167 10 false 1 0.469,0.948 0.594,1.115 0.125,0.167 10 false 2 1.146,0.063 1.271,0.229 0.125,0.167 10 false 5 2.167,1.979 2.292,2.146 0.125,0.167 10 false 6

Tighten the 8 bolts in the order shown in the illustration and install the cylinder head cover sub-assembly LH.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 11103C 23.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

a.
A278734

Apply engine oil to the 8 valve adjusting shims and 8 roller rocker arm pivots, and then install them to the cylinder head sub-assembly.

HINT:

Be sure to install the removed parts in their original locations.



b.
A278733

Apply engine oil to 2 new O-rings and the 8 No. 1 valve rocker arm sub-assemblies, and then install them to the cylinder head sub-assembly.


c.

Using a sealer gun, apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


U146826E03
3.115,1.375 2.427,1.219 2.427,1.219 2.646,1.781 false 5.427,1.885 5.188,2.25 false 5.427,0.719 5.188,1.073 false 3.427,1.74 3.427,1.917 3.427,1.917 3.74,1.917 false 3.76,1.833 3.99,2.021 0.229,0.188 10 false *a 2.25,1.094 2.479,1.281 0.229,0.188 10 false *a 3.74,0.948 3.885,1.125 0.146,0.177 10 false B 4.125,1.563 4.271,1.74 0.146,0.177 10 false B 3.646,2.396 3.875,2.573 0.229,0.177 10 false *f 2.323,2.396 2.552,2.573 0.229,0.177 10 false *f 3.938,1.281 4.167,1.458 0.229,0.177 10 false *f 3.083,2.344 3.26,2.51 0.177,0.167 10 false A 3.083,2.01 3.26,2.177 0.177,0.167 10 false A 5.031,2.229 5.219,2.385 0.188,0.156 10 false *e 4.958,1.781 5.146,1.938 0.188,0.156 10 false *c 5.688,1.583 5.875,1.74 0.188,0.156 10 false *d 4.656,1.448 4.938,1.615 0.281,0.167 10 false B-B 5.031,1.042 5.219,1.198 0.188,0.156 10 false *e 4.938,0.604 5.125,0.76 0.188,0.156 10 false *c 5.688,0.417 5.875,0.573 0.188,0.156 10 false *b 4.656,0.281 4.938,0.448 0.281,0.167 10 false A-A

Text in Illustration
*a Range of B-B *b 0 to 1.0 mm (0 to 0.0394 in.)
*c φ2.5 to 3.5 mm (0.098 to 0.138 in.) *d -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
*e Chamfer edge *f 18.0 mm (0.709 in.)

NOTICE:
·

Clean and degrease the contact surface.

·

Do not apply excessive seal packing.

·

Install the camshaft housing sub-assembly RH within 5 minutes of applying seal packing.


·

After tightening the bolts, if the seal packing is squeezed out onto the seal surface of the chain cover, completely remove it.




d.
U146816E03
0.323,0.323 0.427,0.49 0.104,0.167 10 false 9 2.646,1.583 2.75,1.75 0.104,0.167 10 false 8 0.479,1.76 0.583,1.927 0.104,0.167 10 false 7 3.146,0.24 3.25,0.406 0.104,0.167 10 false 6 0.344,1.031 0.448,1.198 0.104,0.167 10 false 5 3.146,1 3.25,1.167 0.104,0.167 10 false 4 2.063,1.469 2.167,1.635 0.104,0.167 10 false 3 1.74,0.031 1.844,0.198 0.104,0.167 10 false 2 1.24,1.073 1.344,1.24 0.104,0.167 10 false 1

Tighten the 9 bolts in the order shown in the illustration to install the camshaft housing sub-assembly RH.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

HINT:
A278757

Set the intake camshaft RH and the exhaust camshaft RH to the zero-lift position.



e.
U146827E01
2.214,0.843 2.333,1.010 0.119,0.167 10 3 2.108,0.199 2.227,0.366 0.119,0.167 10 2 2.206,1.584 2.325,1.752 0.119,0.167 10 1

Loosen the 3 bolts by 180° in the order shown in the illustration.


f.
U146828E01
2.22,1.6 2.338,1.767 0.119,0.167 10 3 2.08,0.215 2.199,0.383 0.119,0.167 10 2 2.23,0.865 2.349,1.032 0.119,0.167 10 1

Tighten the 3 bolts in the order shown in the illustration.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


g.
U146829E01
3.147,0.821 3.266,0.988 0.119,0.167 10 3 3.147,0.046 3.266,0.214 0.119,0.167 10 2 2.735,1.639 2.853,1.806 0.119,0.167 10 1

Loosen the 3 bolts by 180° in the order shown in the illustration.


h.
U146830E01
3.183,0.867 3.302,1.034 0.119,0.167 10 1 2.813,1.744 2.931,1.911 0.119,0.167 10 3 3.18,0.083 3.299,0.250 0.119,0.167 10 2

Tighten the 3 bolts in the order shown in the illustration.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


i.
U146831E03
0.635,0.833 0.75,1 0.115,0.167 10 false 3 0.635,0.115 0.75,0.281 0.115,0.167 10 false 2 0.792,1.615 0.906,1.781 0.115,0.167 10 false 1

Loosen the 3 bolts by 180° in the order shown in the illustration.


j.
U146832E01
0.831,1.624 0.950,1.791 0.119,0.167 10 3 0.659,0.129 0.778,0.296 0.119,0.167 10 2 0.678,0.81 0.797,0.977 0.119,0.167 10 1

Tighten the 3 bolts in the order shown in the illustration.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

HINT:

After tightening the bolts, if the seal packing is squeezed out onto the seal surface of the chain cover, completely remove it.



Hide 24.INSPECT VALVE CLEARANCE (for Bank 1)

NOTICE:

With the chain sub-assembly (for bank 1) removed, valve heads may contact each other if the camshafts are turned, causing the valve stems to bend. To avoid this, do not turn the intake camshaft RH and exhaust camshaft RH more than the zero-lift rang (The range where the camshafts can be turned lightly by hand).


a.

Using a feeler gauge, check the valve clearance between the cam base circle and the roller surface of the No. 1 valve rocker arm sub-assembly.

A281473

Standard valve clearance (cold):

0.10 to 0.15 mm (0.00394 to 0.00591 in.) for intake

0.20 to 0.24 mm (0.00787 to 0.00945 in.) for exhaust


HINT:
·

Set the intake camshaft RH and the exhaust camshaft RH to the zero-lift position.

·

If the clearance is not as specified, take notes of the value in order to adjust the valve clearance later on.




Hide 25.ADJUST VALVE CLEARANCE (for Bank 1)

a.

Remove the camshaft housing sub-assembly RH.


b.

Remove the No. 1 valve rocker arm sub-assemblies.


c.

Remove the valve adjusting shims.


d.
A281710

Using a micrometer, measure the thickness of the valve adjusting shims.


e.

Calculate the thickness of the valve adjusting shim so that the valve clearance comes within the specified values.

Intake side:

A = B + (C - 0.13 mm (0.00512 in.) x 1.54


Exhaust side:

A = B + (C - 0.22 mm (0.00866 in.) x 1.69


A:

Required valve adjusting shim thickness


B:

Removed valve adjusting shim thickness


C:

Measured valve clearance



f.

Apply engine oil to the inner face of the valve adjusting shims and install them to the valves.

NOTICE:

Check if the shims can be rotated smoothly on the valves.



g.

Install the No. 1 valve rocker arm sub-assemblies.


h.

Install the camshaft housing sub-assembly RH.


Hide 11201 26.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.
A279569E01
2.84,0.368 3.014,0.536 0.174,0.168 10 *a 3.139,0.758 3.139,0.477 3.139,0.477 3.034,0.477 false

Apply a light layer of engine oil to 2 new spark plug tube gaskets and install them to the spark plug tubes as shown in the illustration.

Text in Illustration
*a Spark plug tube edge


b.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly RH.


c.
A279570E03
2.698,1.927 2.833,2.177 2.833,2.177 2.688,2.417 false 2.698,0.833 2.844,1.073 2.844,1.073 2.688,1.313 false 0.938,2.729 0.677,2.458 false 0.688,0.792 0.906,1.01 false 0.74,1.188 0.479,1.563 false 3.24,2.406 3.375,2.563 0.135,0.156 10 false A 3.24,1.833 3.375,1.99 0.135,0.156 10 false A 3.24,1.313 3.375,1.469 0.135,0.156 10 false A 3.24,0.729 3.375,0.885 0.135,0.156 10 false A 2.844,2.083 3.021,2.24 0.177,0.156 10 false *a 2.854,0.979 3.031,1.135 0.177,0.156 10 false *a 0.979,2.698 1.156,2.854 0.177,0.156 10 false *a 0.865,1.042 1.042,1.198 0.177,0.156 10 false *a 0.104,2.24 0.24,2.396 0.135,0.156 10 false C 0.104,0.958 0.24,1.115 0.135,0.156 10 false B 0.354,2.156 0.49,2.313 0.135,0.156 10 false A 0.375,0.99 0.51,1.146 0.135,0.156 10 false A 0.292,1.531 0.469,1.688 0.177,0.156 10 false *b

Using a sealer gun, apply seal packing to the mating surface of cylinder head cover sub-assembly RH as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


Area Application Length
A 10.0 mm (0.394 in.) or more
B 68.0 mm (2.677 in.) or more
C 70.7 mm (2.784 in.) or more

Text in Illustration
*a Arch starting point
*b φ2,0 to 4.0 mm (0.079 to 0.158 in.)


d.
U146814E03
0.854,0.031 0.969,0.198 0.115,0.167 10 false 8 2.771,1.615 2.885,1.781 0.115,0.167 10 false 7 0.531,1.594 0.646,1.76 0.115,0.167 10 false 6 2.5,0.042 2.615,0.208 0.115,0.167 10 false 5 1.385,1.927 1.5,2.094 0.115,0.167 10 false 4 1.635,0.052 1.75,0.219 0.115,0.167 10 false 3 2.906,1.167 3.052,1.385 0.146,0.219 10 false 2 0.51,1.083 0.625,1.25 0.115,0.167 10 false 1

Tighten the 8 bolts in the order shown in the illustration and install the cylinder head cover sub-assembly RH.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 89879 27.INSTALL INJECTOR DRIVER BRACKET

a.
A283322

Install the injector driver bracket with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 19100P 28.INSTALL SPARK PLUG

a.

Using a 14 mm spark plug wrench, install the 4 spark plugs.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 13080 29.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH

Hide 13060B 30.INSTALL CAMSHAFT TIMING INTAKE GEAR ASSEMBLY LH

Hide 13070 31.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY RH

Hide 13050B 32.INSTALL CAMSHAFT TIMING INTAKE GEAR ASSEMBLY RH

Hide 13521 33.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A279563

Install the crankshaft timing gear or sprocket.


Hide 13506 34.INSTALL CHAIN SUB-ASSEMBLY (for Bank 2)

NOTICE:

Do not allow any foreign matter to adhere or to enter into the component parts during installation.


HINT:

Apply engine oil to all component parts of the chain sub-assembly.


a.
A279536E01
0.547,0.123 0.728,0.296 0.180,0.173 10 *2 1.599,0.5 1.779,0.673 0.180,0.173 10 *1 1.328,0.776 1.599,0.644 false 0.752,0.252 0.972,0.369 false

Move the link plate in the direction of the arrow in the illustration to press in the plunger.

Text in Illustration
*1 Link Plate
*2 Plunger


b.
A279537E01
2.059,0.324 2.228,0.490 0.169,0.166 10 *1 3.039,0.276 3.209,0.442 0.169,0.166 10 *2 3.045,0.422 2.879,0.581 false 2.248,0.431 2.791,0.548 false

Insert an approximately 1 mm (0.0394 in.) diameter wire or the like into the chain tensioner assembly through the stopper pin hole, and hold the plunger.

Text in Illustration
*1 First notch of the plunger rack
*2 Stopper Tooth

HINT:

If the stopper pin hole on the link plate and the stopper pin hole on the chain tensioner assembly are not aligned, check that the first notch of the plunger rack is engaged with the stopper tooth. If not engaged, retract the plunger a little so that the first notch of the plunger rack is engaged with the stopper tooth.



c.

Temporarily install the crankshaft pulley spacer and crankshaft pulley.


d.
A334223E01
0.407,1.215 0.604,1.450 0.198,0.235 10 *c 1.506,0.981 1.703,1.216 0.198,0.235 10 *b 3.016,0.014 3.213,0.202 0.198,0.188 10 *a 2.279,1.946 2.623,2.109 0.344,0.164 10 SST 0.986,1.18 0.599,1.311 false 1.15,1.214 1.506,1.1 false 2.483,0.952 2.993,0.144 false 2.513,1.903 2.868,1.304 false 1.038,1.651 1.350,1.830 0.312,0.179 10 10°

Using SST, set the crankshaft pulley pin hole at the position shown in the illustration.

SST
09960-10010  (09962-01000, 09963-01000)

Text in Illustration
*a Crankshaft Pulley Pin Hole
*b Alignment Mark
*c Crankshaft Timing Gear key

NOTICE:

Make sure to perform this operation to prevent the valves and pistons from contacting each other.


HINT:

At this time, the alignment mark on the crankshaft timing gear or sprocket and the crankshaft timing gear key are at the positions shown in the illustration.



e.
U146737E03
2.958,0.49 2.719,0.906 false 0.802,0.906 0.854,1.104 false 3.01,0.375 3.354,0.542 0.344,0.167 10 false SST 0.781,1.146 0.948,1.302 0.167,0.156 10 false *a 0.323,0.865 0.51,1.031 0.188,0.167 10 false *b

Using SST, turn the camshaft timing intake gear assembly LH and align the alignment mark as shown in the illustration.

SST
09960-10010  (09962-01000, 09963-00700)

Text in Illustration
*a Alignment Mark
*b 25°to 30°

NOTICE:

Do not turn the exhaust camshaft LH. If the exhaust camshaft LH is turned, valve heads may come into contact with each other, causing the valve stems to bend.



f.
A334224E03
1.76,2.74 1.479,3.156 false 1.792,0.302 1.333,1.052 true 0.51,0.448 0.344,1.125 false 2.948,1.208 2.948,1.854 false 2.792,1.875 3.156,2.063 0.365,0.188 10 false SST 1.771,0.115 2,0.302 0.229,0.188 10 false *a 0.24,1.156 0.469,1.344 0.229,0.188 10 false *c 1.365,3.156 1.594,3.344 0.229,0.188 10 false *b

Using SST, turn the crankshaft about 200 degrees counterclockwise until the crankshaft pulley pin hole is aligned at the position shown in the illustration.

SST
09960-10010  (09962-01000, 09963-01000)

Text in Illustration
*a Crankshaft Pulley Pin Hole
*b Crankshaft Timing Gear key
*c Cylinder Block Guide Pin

NOTICE:

Never turn the crankshaft clockwise because the valves may come into contact with the piston. Turning the crankshaft clockwise is only allowed when adjusting the key position precisely.


HINT:

At this time, the crankshaft timing gear key is at the position shown in the illustration.



g.

Remove the crankshaft pulley and crankshaft pulley spacer.


h.
A279540E04
2.979,0.813 2.635,1.323 true 3,0.625 3.156,0.781 0.156,0.156 10 false *a 3.063,1.208 3.25,1.385 0.188,0.177 10 false *b

Align the alignment mark on the camshaft timing exhaust gear assembly LH as shown in the illustration.

Text in Illustration
*a Alignment Mark
*b 25° to 30°

NOTICE:

To avoid damaging the valves, do not turn the camshaft timing exhaust gear assembly LH more than the zero-lift range (The range where camshaft timing exhaust gear assembly LH can be turned lightly by hand).



i.
A279541E04
0.385,0.344 1.323,0.25 true 0.365,0.427 1.313,0.708 true 2.917,0.688 2.833,1.115 false 3.01,0.667 3.167,1.083 true 2.781,2.844 3.052,2.229 true 2.75,2.948 2.083,3.083 true 3.104,1.104 3.292,1.271 0.188,0.167 10 false *d 1.896,3.01 2.083,3.177 0.188,0.167 10 false *d 1.333,0.146 1.521,0.313 0.188,0.167 10 false *c 2.74,1.135 2.927,1.302 0.188,0.167 10 false *b 2.99,2.021 3.177,2.188 0.188,0.167 10 false *b 1.323,0.615 1.51,0.781 0.188,0.167 10 false *a

Install the chain sub-assembly in the following order.

Text in Illustration
*a Alignment Mark (Oval)
*b Alignment Mark (Engraved Line)
*c Mark plate (Grayish Blue)
*d Mark plate (Pink)

i.

Align the mark plate (grayish blue) on the chain sub-assembly with the alignment mark (oval) on the crankshaft timing gear or sprocket.


ii.

Align the mark plate (pink) on the chain sub-assembly with the alignment mark (engraved line) on the camshaft timing exhaust gear assembly LH.


iii.

Align the mark plate (pink) on the chain sub-assembly with the alignment mark (engraved line) on the camshaft timing intake gear assembly LH.



j.

Using a 5 mm hexagon socket wrench, install the No. 1 chain vibration damper with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)

HINT:

Apply engine oil to the bolt before install it.



k.
A279532

Install a new O-ring to the cylinder block (for bank 2).


l.
A279531

Install the chain tensioner slipper.


m.

Install the No. 2 chain tensioner assembly with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


n.
A279542E04
0.385,0.333 1.313,0.24 false 0.365,0.458 1.313,0.74 false 2.917,0.615 2.833,1.042 false 3.021,0.625 3.167,1.031 false 2.729,2.802 3.01,2.146 true 2.698,2.906 2.031,3.042 true 3.083,1.042 3.271,1.208 0.188,0.167 10 false *d 1.833,2.958 2.021,3.125 0.188,0.167 10 false *d 1.333,0.115 1.521,0.281 0.188,0.167 10 false *c 2.719,1.042 2.906,1.208 0.188,0.167 10 false *b 2.948,1.958 3.135,2.125 0.188,0.167 10 false *b 1.333,0.646 1.521,0.813 0.188,0.167 10 false *a

Check that the chain is correctly installed.

Text in Illustration
*a Alignment Mark (Oval)
*b Alignment Mark (Engraved Line)
*c Mark plate (Grayish Blue)
*d Mark plate (Pink)

i.

The mark plate (grayish blue) on the chain sub-assembly is aligned with the alignment mark (oval) on the crankshaft timing gear or sprocket.


ii.

The mark plate (pink) on the chain sub-assembly is aligned with the alignment mark (engraved line) on the camshaft timing intake gear assembly LH.


iii.

The mark plate (pink) on the chain sub-assembly is aligned with the alignment mark (engraved line) on the camshaft timing exhaust gear assembly LH.



o.

Pull out the wire or the like from the No. 2 chain tensioner assembly.


p.

Temporarily install the crankshaft pulley spacer and crankshaft pulley.


q.

Using SST, turn the crankshaft clockwise to make sure that there are no abnormal conditions.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

Be sure to perform this confirmation.



Hide 13506 35.INSTALL CHAIN SUB-ASSEMBLY (for Bank 1)

NOTICE:

Do not allow any foreign matter to adhere or to enter into the component parts during installation.


HINT:

Apply engine oil to all component parts of the chain sub-assembly.


a.
A279544E01
0.214,1.078 0.384,1.246 0.170,0.168 10 *1 1.749,0.661 1.919,0.829 0.170,0.168 10 *2 1.099,1.032 0.404,1.154 false 1.383,0.662 1.737,0.76 false

Move the link plate in the direction of the arrow in the illustration to press in the plunger.

Text in Illustration
*1 Link Plate
*2 Plunger


b.
A279545E03
2.188,0.458 2,0.302 false 2.292,0.479 2.521,0.667 false 1.823,0.188 2.104,0.385 0.281,0.198 10 false *2 2.49,0.698 2.667,0.854 0.177,0.156 10 false *1

Insert a 2.5 mm (0.098 in.) diameter hexagon wrench into the No. 1 chain tensioner assembly through the stopper pin hole, and hold the plunger.

Text in Illustration
*1 First notch of the plunger rack
*2 Stopper Tooth

HINT:

If the stopper pin hole on the link plate and the stopper pin hole on the chain tensioner assembly are not aligned, check that the first notch of the plunger rack is engaged with the stopper tooth. If not engaged, retract the plunger a little so that the first notch of the plunger rack is engaged with the stopper tooth.



c.
A334221E03
3.24,0.177 3.01,0.802 true 3.271,1.875 3,1.104 true 2.156,2.573 1.594,2.75 true 1.458,2.677 0.615,3.063 false 0.875,1 0.656,2.344 true 0.406,1.219 0.25,2.167 true 0.104,2.208 0.49,2.396 0.385,0.188 10 false SST 2.177,2.458 2.375,2.646 0.198,0.188 10 false *a 0.542,2.375 0.74,2.563 0.198,0.188 10 false *b 0.438,2.979 0.635,3.167 0.198,0.188 10 false *c 3.208,1.885 3.406,2.073 0.198,0.188 10 false *a 3.208,0.01 3.406,0.198 0.198,0.188 10 false *a 1.771,3.031 2.052,3.208 0.281,0.177 10 false 10°

Using SST, turn the crankshaft pulley until the alignment marks on the camshaft timing intake gear assembly LH and the camshaft timing exhaust gear assembly LH, and the crankshaft pulley pin hole are aligned at the positions shown in the illustration.

SST
09960-10010  (09962-01000, 09963-01000)

Text in Illustration
*a Alignment Mark
*b Crankshaft Pulley Pin Hole
*c Crankshaft Timing Gear Key

HINT:

At this time, the alignment mark on the crankshaft timing gear or sprocket and the crankshaft timing gear key are at the positions shown in the illustration.



d.

Remove the crankshaft pulley and crankshaft pulley spacer.


e.
A279547E01
0.592,0.976 0.759,1.145 0.167,0.169 10 *a 1.343,0.879 0.795,1.057 0.795,1.057 1.339,1.208 false

Align the alignment marks of the camshaft timing intake gear assembly RH and camshaft timing exhaust gear assembly RH as shown in the illustration.

Text in Illustration
*a Alignment Mark

NOTICE:

To avoid damaging the valves, do not turn the camshaft timing intake gear assembly RH and camshaft timing exhaust gear assembly RH more than the zero-lift range (The range where the camshafts can be turned lightly by hand).



f.
A279548E03
0.823,0.5 1.302,0.396 false 0.75,0.615 0.438,1.135 false 0.448,2.719 0.677,2.135 false 0.375,2.677 0.229,2.135 false 2.115,2.969 1.542,2.729 false 2.063,3.052 1.531,3.083 false 1.302,0.281 1.479,0.448 0.177,0.167 10 false *d 0.323,1.115 0.5,1.281 0.177,0.167 10 false *b 0.135,1.927 0.313,2.094 0.177,0.167 10 false *d 1.323,2.99 1.5,3.156 0.177,0.167 10 false *c 0.625,1.938 0.802,2.104 0.177,0.167 10 false *b 1.333,2.625 1.51,2.792 0.177,0.167 10 false *a

Install the chain sub-assembly in the following order.

Text in Illustration
*a Alignment Mark (Oval)
*b Alignment Mark (Engraved Line)
*c Mark plate (Grayish Blue)
*d Mark plate (Pink)

i.

Align the mark plate (grayish blue) on the chain sub-assembly with the alignment mark (oval) on the crankshaft timing gear or sprocket.


ii.

Align the mark plate (pink) on the chain sub-assembly with the alignment mark (engraved line) on the camshaft timing intake gear assembly RH.


iii.

Align the mark plate (pink) on the chain sub-assembly with the alignment mark (engraved line) on the camshaft timing exhaust gear assembly RH.



g.

Using a 5 mm hexagon socket wrench, install the No. 1 chain vibration damper with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)

HINT:

Apply engine oil to the bolt before install it.



h.
A279527

Install the chain tensioner slipper.


i.

Install the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


j.
A279549E01
1.34,0.19 1.509,0.353 0.169,0.163 10 *d 1.344,0.658 1.514,0.822 0.169,0.163 10 *b 0.174,2.091 0.344,2.254 0.169,0.163 10 *d 1.907,0.68 2.076,0.843 0.169,0.163 10 *c 0.611,2.088 0.780,2.251 0.169,0.163 10 *b 1.907,0.19 2.076,0.353 0.169,0.163 10 *a 0.82,0.475 1.325,0.313 false 0.764,0.595 1.333,0.768 false 2.68,0.749 2.106,0.305 false 2.607,0.82 2.096,0.785 false 0.247,2.267 0.404,2.743 false 0.491,2.781 0.661,2.265 false

Check that the chain is correctly installed.

Text in Illustration
*a Alignment Mark (Oval)
*b Alignment Mark (Engraved Line)
*c Mark plate (Grayish Blue)
*d Mark plate (Pink)

i.

The mark plate (grayish blue) on the chain sub-assembly is aligned with the alignment mark (oval) on the crankshaft timing gear or sprocket.


ii.

The mark plate (pink) on the chain sub-assembly is aligned with the alignment mark (engraved line) on the camshaft timing intake gear assembly RH.


iii.

The mark plate (pink) on the chain sub-assembly is aligned with the alignment mark (engraved line) on the camshaft timing exhaust gear assembly RH.



k.

Pull out the hexagon wrench from the No. 1 chain tensioner assembly.


l.

Temporarily install the crankshaft pulley spacer and crankshaft pulley.


m.

Using SST, turn the crankshaft clockwise to make sure that there are no abnormal conditions.

SST
09960-10010  (09962-01000, 09963-01000)

NOTICE:

Be sure to perform this confirmation.



n.

Remove the crankshaft pulley and crankshaft pulley spacer.


Hide 11302 36.INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

a.

Apply a light layer of engine oil to 4 new O-rings and attach them to the engine.


b.

Clean and degrease the contact surface.


c.

If there are gaps at positions shown in the illustration, fill up with seal packing by using a sealer gun.

Seal packing:

Three Bond 1217G, 1217H or equivalent


A281483


d.

Using a sealer gun, apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


A283341E04
1.146,0.052 1.323,0.229 0.177,0.177 10 false *a 2.719,0.031 2.896,0.208 0.177,0.177 10 false *c 0.25,0.229 0.917,0.698 0.667,0.469 10 false 14.5 mm (0.571 in.) 0.281,0.667 0.958,1.156 0.677,0.49 10 false 17.5 mm(0.689 in.) 1.781,0.458 2.448,0.958 0.667,0.5 10 false 24.5 mm(0.965 in.) 1.833,1 3.167,1.167 1.333,0.167 10 true 316.2 mm (12.449 in.) 3.042,0.229 4.25,0.375 1.208,0.146 10 true 127 mm (5.000 in.) 3.26,0.552 3.917,1.177 0.656,0.625 10 false 18.5 mm(0.728 in.) 0.885,1.542 1.021,1.698 0.135,0.156 10 true A 0.875,2.156 1.031,2.333 0.156,0.177 10 true A 1.469,3.323 1.604,3.479 0.135,0.156 10 true B 1.865,3.323 2,3.521 0.135,0.198 10 true B 2.667,1.604 2.802,1.76 0.135,0.156 10 false C 2.656,2.229 2.792,2.385 0.135,0.156 10 true C 6.615,3.25 6.75,3.406 0.135,0.156 10 true D 7,3.26 7.135,3.417 0.135,0.156 10 false D 1.083,4.208 1.26,4.385 0.177,0.177 10 false *e 1.396,4.26 1.573,4.438 0.177,0.177 10 false *f 2.781,4.385 2.958,4.563 0.177,0.177 10 false *g 2.313,4.646 2.49,4.823 0.177,0.177 10 false *e 4.604,5.073 4.781,5.25 0.177,0.177 10 false *e 6.354,5.104 6.531,5.281 0.177,0.177 10 false *e 6.354,5.375 6.531,5.552 0.177,0.177 10 false *i 4.865,5.073 5.042,5.25 0.177,0.177 10 false *h 0.813,3.99 1.458,4.135 0.646,0.146 10 false A - A (*a) 2.51,4.198 3.156,4.344 0.646,0.146 10 false B - B (*b) 4.438,4.396 5.083,4.542 0.646,0.146 10 false C - C (*c) 5.792,4.25 6.438,4.396 0.646,0.146 10 false D - D (*d)

Text in Illustration
*a Area A *b Boss (5 locations)
*c Area B *d Other than ranges A and B
*e φ3.5 to 4.5 mm (0.138 to 0.177 in.) *f 2.0 mm (0.079 in.)
*g φ12 mm (0.472 in.) *h 2.5 mm (0.098 in.)
*i 0.5 mm (0.0197 in.) - -

NOTICE:
·

Clean and degrease the contact surface.

·

Install the chain cover within 5 minutes of applying seal packing.




e.

Temporarily install the timing chain or belt cover sub-assembly with the 32 bolts.


f.

Securely tighten the 32 bolts in the order as shown in the illustration.

A303424E01
0.828,1.495 1.060,1.664 0.233,0.169 10 26 5.676,3.021 5.908,3.190 0.233,0.169 10 32 6.301,2.454 6.534,2.623 0.233,0.169 10 31 6.302,1.513 6.535,1.682 0.233,0.169 10 30 5.861,1.306 6.094,1.475 0.233,0.169 10 29 1.489,3.047 1.722,3.216 0.233,0.169 10 28 0.808,2.501 1.040,2.670 0.233,0.169 10 27 1.634,0.848 1.867,1.017 0.233,0.169 10 25 5.323,3.047 5.555,3.216 0.233,0.169 10 24 4.921,3.02 5.153,3.189 0.233,0.169 10 23 4.735,2.875 4.968,3.044 0.233,0.169 10 22 4.499,2.807 4.731,2.976 0.233,0.169 10 21 4.928,1.094 5.163,1.267 0.235,0.173 10 20 4.697,1.217 4.929,1.386 0.233,0.169 10 19 1.858,3.034 2.090,3.203 0.233,0.169 10 18 2.299,3.015 2.532,3.184 0.233,0.169 10 17 2.523,2.925 2.755,3.094 0.233,0.169 10 16 2.011,0.979 2.243,1.148 0.233,0.169 10 15 2.459,1.161 2.691,1.330 0.233,0.169 10 14 4.196,2.843 4.429,3.012 0.233,0.169 10 13 3.934,3.054 4.166,3.223 0.233,0.169 10 12 3.579,3.261 3.812,3.430 0.233,0.169 10 11 3.175,3.27 3.408,3.439 0.233,0.169 10 10 2.782,3.043 2.937,3.212 0.154,0.169 10 9 4.216,1.104 4.371,1.273 0.154,0.169 10 8 3.546,1.111 3.701,1.280 0.154,0.169 10 7 3.124,1.304 3.278,1.473 0.154,0.169 10 6 1.678,1.989 1.832,2.158 0.154,0.169 10 5 5.503,1.997 5.658,2.166 0.154,0.169 10 4 2.255,2.095 2.409,2.264 0.154,0.169 10 3 5.198,2.231 5.352,2.400 0.154,0.169 10 2 3.128,2.411 3.282,2.580 0.154,0.169 10 1

Text in Illustration
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D

Torque:
Bolt A and B : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt C and D : 25 N*m (255 kgf*cm, 18 ft.*lbf)

Bolt Length:
Item Length Item Length
Bolt A 20 mm (0.787 in.) Bolt B 50 mm (1.969 in.)
Bolt C 25 mm (0.984 in.) Bolt D 60 mm (2.362 in.)



Hide 11302A 37.INSTALL TIMING CHAIN COVER OIL SEAL

a.
A375976E01
1.187,1.371 1.139,1.828 false 0.947,1.859 1.293,2.049 0.346,0.190 10 SST 1.644,2.06 1.990,2.249 0.346,0.190 10 SST 2.067,2.71 1.837,2.281 1.837,2.281 1.798,2.705 false 2.796,2.122 3.141,2.311 0.346,0.190 10 SST 2.515,2.528 2.753,2.218 2.753,2.218 2.347,2.445 false

Degrease the area in which to press-fit the oil seal for the timing chain or belt cover sub-assembly.


b.

Using SST and a hammer, tap in a new timing chain or belt cover oil seal until its surface is flush with the timing chain or belt cover sub-assembly edge.

SST
09950-60010  (09952-06010, 09951-00490, 09951-00650)
09950-70010  (09951-07100)

NOTICE:
·

Do not tap the oil seal at an angle.

·

Do not deform the oil seal.

·

Keep the lip free from foreign matter.

·

Do not apply engine oil to the dust seal section.

·

Do not apply engine oil, etc., to the oil seal or the timing chain or belt cover sub-assembly, because doing so could cause an engine oil leak.



HINT:

Alternatively, the tapping depth of the timing chain cover oil seal can be 0 to -1.0 mm (0 to -0.0394 in.) from the timing chain cover end surface.



Hide 13471 38.INSTALL CRANKSHAFT PULLEY

a.

Install the crankshaft pulley spacer.


b.

Install a new O-ring to the crankshaft pulley spacer.


c.
A302559E01
2.489,1.018 2.872,0.343 false 2.896,0.175 3.089,0.351 0.193,0.177 10 *2 0.824,1.037 1.227,0.343 false 1.252,0.175 1.445,0.351 0.193,0.177 10 *1

Install the crankshaft pulley while aligning the knock hole of the pulley with the knock pin on the crankshaft pulley spacer.

Text in Illustration
*1 Knock Hole
*2 Knock Pin


d.

Apply engine oil to threads and seat sections of the crankshaft pulley set bolt.


e.
A302562E03
1.99,3.146 2.698,3.052 false 0.896,4.167 1.719,3.865 false 1.083,2.188 1.177,1.896 false 0.74,3.833 1.01,3.875 false 2.719,2.938 2.906,3.115 0.188,0.177 10 false *1 0.708,4.104 0.896,4.281 0.188,0.177 10 false *1 0.917,2.188 1.271,2.365 0.354,0.177 10 false SST 0.396,3.74 0.75,3.917 0.354,0.177 10 false SST

Install SST to the crankshaft pulley.

SST
09213-80010  (90179-10016, 09213-08010, 09213-08110)

HINT:

Position the projections on SST in the direction as shown in the illustration to prevent SST from separating from the crankshaft pulley.


Text in Illustration
*1 Claw


f.
A302563E03
1.208,1.49 1.115,1.781 false 1.542,1.906 1.74,2.094 0.198,0.188 10 false *a 3.021,1.198 3.208,1.406 0.188,0.208 10 false *b 0.958,1.813 1.271,2 0.313,0.188 10 false SST

Using SST, hold the crankshaft pulley and tighten the crankshaft pulley set bolt.

SST
09213-80010  (90179-10016, 09213-08010, 09213-08110)

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

Text in Illustration
*a Hold
*b Turn


g.
A281493E03
1.542,0.948 0.573,1.688 false 2.125,0.99 2.542,1.813 false 2.5,1.875 2.677,2.052 0.177,0.177 10 false *b 0.365,1.656 0.542,1.833 0.177,0.177 10 false *a

Using a marker, draw the reference line (A) on the crankshaft pulley set bolt and also the reference line (B) on the crankshaft pulley according to the line engraved around the crankshaft pulley set bolt head as shown in the illustration.

Text in Illustration
*a Reference Line A
*b Reference Line B

HINT:

There are carved lines on the crankshaft pulley set bolt head every 90°.



h.
A302564E03
0.938,4.031 1.104,3.74 true 2.823,1.427 2.073,1.104 true 2.573,1.708 1.969,1.146 true 1.406,4.198 1.719,4.396 0.313,0.198 10 false *a 2.917,3.302 3.229,3.5 0.313,0.198 10 false *b 2.635,1.708 2.948,1.906 0.313,0.198 10 false *c 2.865,1.365 3.177,1.563 0.313,0.198 10 false *d 0.781,4.073 1.135,4.281 0.354,0.208 10 false SST

Using SST, hold the crankshaft pulley, and tighten the crankshaft pulley set bolt by 90° until the reference lines A and B are aligned.

SST
09213-80010  (90179-10016, 09213-08010, 09213-08110)

Text in Illustration
*a Hold
*b Turn
*c Reference Line A
*d Reference Line B


Hide 16331A 39.INSTALL THERMOSTAT

a.

Attach a new gasket to the thermostat.


Hide 16331 40.INSTALL WATER OUTLET

a.
A281051

Install the thermostat and water outlet with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 16100 41.INSTALL ENGINE WATER PUMP ASSEMBLY

a.
A279726

Install a new gasket and the water pump assembly with the 5 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 16173 42.INSTALL WATER PUMP PULLEY

a.

Temporarily install the water pump pulley with the 3 bolts.


b.
A281471E01
0.932,1.612 1.250,1.793 0.318,0.181 10 SST 1.655,1.389 1.305,1.683 false

Using SST, hold the water pump pulley.

SST
09960-10010  (09962-01000, 09963-00700)


c.

Securely tighten the 3 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 16603 43.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A276070

Install the idler pulley cover and No. 1 idler pulley sub-assembly with the bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 16603 44.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A276069

Install the idler pulley cover and No. 1 idler pulley sub-assembly with the bolt.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 12204 45.INSTALL PCV VALVE SUB-ASSEMBLY

a.
A092670E36
2.24,1.073 2.479,1.438 true 2.448,1.49 2.76,1.688 0.313,0.198 10 false *1

Apply adhesive to 2 or 3 threads of the PCV valve sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Text in Illustration
*1 Adhesive


b.
A278795

Using a 19 mm deep socket wrench, install the PCV valve sub-assembly.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 16322 46.INSTALL WATER INLET PIPE

a.
A280856

Attach 2 new O-rings to the cylinder block.


b.
A279573

Install the water inlet pipe with the 4 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


c.

Connect the No. 3 water by-pass hose with the clamp.


Hide 11181 47.INSTALL REAR CYLINDER HEAD PLATE (for Manual Transmission)

a.
A279600E03
0.977,1.87 1.112,2.030 0.135,0.159 10 A 1.962,0.146 2.237,0.305 0.275,0.159 10 A-A 0.977,0.547 1.112,0.706 0.135,0.159 10 A 2.955,1.593 3.166,1.776 0.212,0.183 10 *c 2.267,1.593 2.479,1.776 0.212,0.183 10 *b 2.525,0.355 2.737,0.538 0.212,0.183 10 *a 2.662,1.124 3.039,1.227 3.039,1.227 3.039,1.583 false

Using a sealer gun, apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Three Bond 1217G, 1217H or equivalent


Text in Illustration
*a φ2,0 to 4.0 mm (0.079 to 0.158 in.)
*b Within 1.0 mm (0.0394 in.)
*c Chamfer edge

NOTICE:
·

Clean and degrease the contact surface.

·

Install the rear cylinder head plate within 5 minutes of applying seal packing.




b.
A278731

Install the rear cylinder head plate with the 3 bolts.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 29300 48.INSTALL VACUUM PUMP ASSEMBLY (for Automatic Transmission)

Hide 11401S 49.INSTALL PCV HOSE CONNECTOR

a.
A280851

Connect the No. 2 water by-pass hose to the PCV hose connector and water inlet pipe with the clips.


b.

Install the PCV hose connector with the 3 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 83530 50.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

a.

Clean and degrease the threads of the engine oil pressure switch assembly.


b.
A174329E05
2.25,1.104 2.615,1.5 false 2.698,1.448 2.896,1.667 0.198,0.219 10 false *1

Apply adhesive 1324 to the threads of the engine oil pressure switch assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Text in Illustration
*1 Adhesive 1324

NOTICE:

Keep the oil hole free from adhesive.



c.
A280849E01
1.862,1.094 1.658,1.273 false 1.463,1.202 1.639,1.357 0.177,0.155 10 *1

Using a 24 mm deep socket wrench, install the engine oil pressure switch assembly.

Text in Illustration
*1 24 mm Deep Socket Wrench

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



Hide 51.INSTALL ENGINE OIL TEMPERATURE SENSOR

a.

Attach a new gasket to the engine oil temperature sensor.


b.
A280848E01
1.48,1.403 1.831,1.603 false 1.865,1.553 2.023,1.703 0.158,0.151 10 *1

Using a 19 mm deep socket wrench, install the engine oil temperature sensor.

Text in Illustration
*1 19 mm Deep Socket Wrench

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 15330 52.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE

a.
A276534E05
2.24,0.875 2.875,0.427 true 2.229,0.979 2.875,1.146 true 2.906,0.302 3.063,0.479 0.156,0.177 10 false *1 2.927,1.052 3.083,1.229 0.156,0.177 10 false *2

Install the back-up ring to the camshaft timing oil control valve (for exhaust side of bank 2).

Text in Illustration
*1 O-ring
*2 Back-up ring


b.

Install a new O-ring to the camshaft timing oil control valve (for exhaust side of bank 2).


c.

Apply a light coat of engine oil to the O-ring.


d.
A280847

Install the camshaft timing oil control valve (for exhaust side of bank 2) with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


e.

Install the back-up ring to the camshaft timing oil control valve (for intake side of bank 2).


f.

Install a new O-ring to the camshaft timing oil control valve (for intake side of bank 2).


g.

Apply a light coat of engine oil to the O-ring.


h.
A280846

Install the camshaft timing oil control valve (for intake side of bank 2) with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


i.

Install the back-up ring to the camshaft timing oil control valve (for exhaust side of bank 1).


j.

Install a new O-ring to the camshaft timing oil control valve (for exhaust side of bank 1).


k.

Apply a light coat of engine oil to the O-ring.


l.
A280845

Install the camshaft timing oil control valve (for exhaust side of bank 1) with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


m.

Install the back-up ring to the camshaft timing oil control valve (for intake side of bank 1).


n.

Install a new O-ring to the camshaft timing oil control valve (for intake side of bank 1).


o.

Apply a light coat of engine oil to the O-ring.


p.
A280844

Install the camshaft timing oil control valve (for intake side of bank 1) with the 2 bolts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 11102A 53.INSTALL VVT SENSOR

a.

Install a new O-ring to the VVT sensor (for exhaust side of bank 2).


b.

Apply a light coat of engine oil to the O-ring.


c.
A280843

Install the VVT sensor (for exhaust side of bank 2) with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


d.

Install a new O-ring to the VVT sensor (for intake side of bank 2).


e.

Apply a light coat of engine oil to the O-ring.


f.
A280842

Install the VVT sensor (for intake side of bank 2) with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


g.

Install a new O-ring to the VVT sensor (for exhaust side of bank 1).


h.

Apply a light coat of engine oil to the O-ring.


i.
A280841

Install the VVT sensor (for exhaust side of bank 1) with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


j.

Install a new O-ring to the VVT sensor (for intake side of bank 1).


k.

Apply a light coat of engine oil to the O-ring.


l.
A280840

Install the VVT sensor (for intake side of bank 1) with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 11401G 54.INSTALL CRANK POSITION SENSOR

a.
A280839

Install the crank position sensor with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 89615 55.INSTALL KNOCK CONTROL SENSOR

a.
U146787

Install the 2 knock control sensors onto the cylinder block with the 2 bolts as shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Text in Illustration
V100136

Engine front


Hide 89422 56.INSTALL E.F.I. WATER TEMPERATURE SENSOR

a.
A280837

Using a 19 mm union nut wrench, install a new gasket and the E.F.I. water temperature sensor.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 15600A 57.INSTALL OIL FILTER UNION

a.
A281050

Install the oil filter union.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 15601 58.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Apply engine oil to the installation surface of the oil filter sub-assembly.


b.
A281048E04
1.854,0.76 1.854,0.323 1.854,0.323 2.052,0.323 true 2.104,0.24 2.448,0.458 0.344,0.219 10 false SST

Using SST, install the oil filter sub-assembly.

SST
09228-22020  

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 59.INSTALL OIL FILLER CAP

a.

Install the oil filler cap.