Home › Engine / Hybrid System › FA20 FUEL › FUEL INJECTOR(for Port Injection) › from 2016.06
RM2090E _51 Engine / Hybrid System _060667 FA20 FUEL _0297500 FUEL INJECTOR(for Port Injection) A

FA20 FUEL  FUEL INJECTOR(for Port Injection)  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

a.

Apply gasoline to a new fuel injector O-ring and a new fuel injector grommet, and then install them to the injector.

NOTICE:

Check that there is no damage or foreign material in the groove of the injector when installing the fuel injector O-ring and fuel injector grommet.



b.

Install the 4 fuel injector assemblies to the fuel delivery pipe.

NOTICE:
·

Check that there are no foreign objects or scratches in the insertion opening of the fuel delivery pipe.

·

Take sufficient care not to twist the O-ring.

·

If the injector does not rotate smoothly after installing it to the fuel delivery pipe, remove the injector and reinstall it with a new O-ring.




Hide 23255A 2.INSTALL FUEL INJECTOR SEAL (for Bank 1)

a.

Install 2 new fuel injector seals.


Hide 23255A 3.INSTALL FUEL INJECTOR SEAL

Hide 23255A 4.INSTALL FUEL INJECTOR SEAL (for Bank 2)

a.

Install 2 new fuel injector seals.


Hide 5.INSTALL FUEL DELIVERY PIPE (for Bank 1)

a.

Install the fuel delivery pipe (with injector) to the intake manifold with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Engage the clamp to connect the wire harness.


c.

Connect the 2 fuel injector assembly connectors.

HINT:

Connect the connector, aligning it with the baffles on the fuel injector assembly on the fuel delivery pipe.



d.

Connect the fuel delivery tube to the fuel delivery pipe (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).


Hide 6.INSTALL FUEL DELIVERY PIPE (for Bank 2)

a.

Install the fuel delivery pipe (with injector) to the intake manifold with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the 2 injector connectors and clamp.

HINT:

Connect the connector, aligning it with the baffles on the fuel injector assembly on the fuel delivery pipe.



c.

Connect the fuel delivery tube to the fuel delivery pipe (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23807 7.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY (for Clamp Type)

a.

Connect the No. 2 fuel vapor feed hose to the fuel delivery pipe sub-assembly.


b.

Install the fuel delivery pipe sub-assembly to the intake manifold with the bolt.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 77259D 8.CONNECT NO. 1 FUEL HOSE (for Clamp Type)

a.

Connect the No. 1 fuel hose to the fuel delivery pipe with the clamp.


b.

Tighten the hose clamp bolt.


Hide 23261A 9.INSTALL INJECTOR COVER (for Bank 2)

a.

for Resin Intake Manifold:

i.

Install the injector cover (for bank 2) to the intake manifold with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



b.

for Aluminum Intake Manifold:

i.

Engage the 2 guides and install the injector cover to the intake manifold with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



c.

Install the wire harness clamp bracket to the injector cover (for bank 2) with the bolt.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 77279G 10.CONNECT NO. 2 FUEL HOSE (for Metal Type)

a.

Connect the No. 2 fuel hose to the fuel delivery pipe sub-assembly with the clamp.


Hide 77419 11.CONNECT NO. 3 FUEL HOSE (for Metal Type)

a.

Connect the No. 3 fuel hose to the fuel delivery pipe sub-assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).


Hide 77259D 12.CONNECT NO. 1 FUEL HOSE (for Metal Type)

a.

Connect the No. 1 fuel hose to the fuel delivery pipe (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).


Hide 23261A 13.INSTALL INJECTOR COVER (for Bank 1)

a.

for Resin Intake Manifold:

i.

Install the injector cover (for bank 1) to the intake manifold with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



b.

for Aluminum Intake Manifold:

i.

Engage the 2 guides and install the injector cover to the intake manifold with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



c.

Engage the 4 clamps to install the wire harness to the injector cover (for bank 1).


Hide 17764D 15.INSTALL CHAMBER ASSEMBLY

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL