Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION FLUID
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297542 AUTOMATIC TRANSMISSION FLUID A

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE AUTOMATIC TRANSMISSION FLUID

a.

Lift the vehicle. [*1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.

Remove the No. 2 engine under cover (See page Engine / Hybrid System>FA20 INTAKE / EXHAUST>EXHAUST PIPE>REMOVAL).


c.

Remove the drain plug and gasket, and drain the ATF. [*2]


d.

Temporarily install the drain plug and gasket. [*3]

HINT:

Reuse the old gasket. The drain plug will be removed again to adjust the fluid level.



e.
C258469E03
1.99,1.667 2.281,1.667 false 1.51,1.417 1.51,1.74 true 1.667,4.094 1.667,4.323 false 2.323,1.573 2.49,1.76 0.167,0.188 10 false *1 1.427,1.76 1.594,1.948 0.167,0.188 10 false *a 1.594,4.323 1.76,4.51 0.167,0.188 10 false *2

Remove the refill plug with O-ring, overflow plug and gasket. [*4]

Text in Illustration
*1 Refill Plug
*2 Overflow Plug
*a Refill Hole


f.
C369071E01
0.698,1.208 0.844,1.208 0.844,1.208 1.094,0.823 true 2.375,1.156 2.24,1.156 2.24,1.156 1.781,0.844 true 0.51,1.115 0.677,1.313 0.167,0.198 10 false *a 2.427,1.052 2.594,1.25 0.167,0.198 10 false *1

Add fluid to the refill hole until it flows out of the overflow tube. [*5]

Text in Illustration
*1 Overflow Tube
*a Specified Fluid Level

NOTICE:

Use Toyota Genuine ATF WS.



g.

Wait until the fluid flow slows and only drops come out. [*6]


h.

Temporarily install the overflow plug and gasket. [*7]

HINT:

Reuse the old gasket. The overflow plug will be removed again to adjust the fluid level.



i.

Add fluid to the refill hole using the amount of fluid specified for removal and installation of the oil pan. [*8]

HINT:

Specified amount of fluid is 2.0 liters (2.1 US qts, 1.8 Imp. qts).



j.

Temporarily install the refill plug with O-ring. [*9]

HINT:

Reuse the old O-ring. The refill plug will be removed again to adjust the fluid level.



k.

Lower the vehicle. [*10]


l.

Start the engine. [*11]

NOTICE:

Make sure that the A/C switch is off.



m.

Slowly move the shift lever from P to M. Then return the shift lever to P. [*12]

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transmission.



n.

Allow the engine to idle for 30 seconds to warm it up. [*13]


o.

Turn the ignition switch off. [*14]


p.

Repeat steps [*1] to [*14].


q.

Repeat steps [*1] to [*2].


r.

Install the drain plug and a new gasket.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


s.

Repeat steps [*4] to [*10].



u.

Install the No. 2 engine under cover (See page Engine / Hybrid System>FA20 INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION).


v.

Lower the vehicle.


w.

Operation complete.