The input speed sensor NT inputs signal into the TCM as a signal of the input axis revolutions.
The TCM carries out shift timing control based upon signals from the input speed sensor NT and the output speed sensor SP2.
| DTC No. | DTC Detection Condition
1.
Diagnosis Condition 2.
Malfunction Status 3.
Malfunction Time 4.
Other |
Trouble Area |
|---|---|---|
| P0717 | 1.
The shift solenoid valve (S1, S2, S3, S4, SR, SL1, SL2, SLT), output speed sensor SP2 and shift position sensor are normal. While the vehicle is driven with shift lever in D, when the input speed sensor NT revolutions calculated from the shift solenoid valve SP2 are 550 rpm or more. (2.5 seconds or more have elapsed after moving the shift lever to D. However, if there is a malfunction with the oil temperature sensor, or the oil temperature is 20°C (68°F) or less, then 10 seconds or more after moving the shift lever to D) 2.
While the shift solenoid valve SP2 outputs 12 pulses, the input speed sensor NT does not detect even 1 pulse. 3.
Detected 500 times consecutively. 4.
1-trip detection logic |
·
Input speed sensor NT ·
TCM ·
Harness and connector |
This DTC indicates that pulse is not output from the input speed sensor NT or is output only little. The input speed sensor NT terminal of the TCM detects the revolving signal from input speed sensor NT (input RPM). The TCM outputs a gearshift signal comparing the input speed sensor NT with the output speed sensor SP2.
While the vehicle is operating in the shift position of D, the output shaft revolution is 550rpm or more*, the TCM detects the trouble, illuminates the MIL and stores the DTC.
*: The engine speed is 400 rpm or more.
Perform the universal trip to clear permanent DTCs (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the GTS, read the "Data List".
| Item | Measurement Item/
Range (display) |
Normal Condition |
|---|---|---|
| SPD (NT) | Input shaft speed/
Min.: 0 rpm Max.: 12,750 rpm |
|
SPD (NT) is always 0 while driving:
Open or short in the sensor or circuit.
SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
Check the input speed sensor NT installation.
The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
OK
NG
Disconnect the L5 speed sensor connector.
Perform inspection of the input speed sensor NT (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>INSPECTION).
Connect the L5 speed sensor connector.
OK
NG
Disconnect the A19 TCM connector.
Disconnect the L5 speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L5-1(NT+) - A19-17(NT+) | Always | Below 1 Ω |
| L5-2(NT-) - A19-28(NT-) | Always | Below 1 Ω |
| L5-1(NT+) - Body ground | Always | 10 kΩ or higher |
| L5-2(NT-) - Body ground | Always | 10 kΩ or higher |
Connect the A19 TCM connector.
Connect the L5 speed sensor connector.
OK
NG
Replace the TCM (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>TCM>REMOVAL).
NEXT