Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM C

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0722  Output Speed Sensor Circuit No Signal  


DESCRIPTION

The output speed sensor SP2 inputs signal into the TCM as a signal of the output axis revolutions.

The TCM carries out shift timing control based upon signals from the output speed sensor SP2 and the input speed sensor NT.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0722
1.

The shift solenoid valve (S1, S2, S3, S4, SR, SL1, SL2, SLT), input speed sensor NT and shift position sensor are normal

With the shift lever is in D, driving in 1st gear 6 km/h or more, in 2nd gear 9 km/h or more, in 3rd gear 13 km/h or more, in 4th gear 18 km/h or more, in 5th gear 25 km/h or more, and in 6th gear, 30 km/h or more. (2.5 seconds or more have elapsed after moving the shift lever to D. However, if there is a malfunction with the oil temperature sensor, or the oil temperature is 20°C (68°F) or less, then 10 seconds or more after moving the shift lever to D)

2.

While the input speed sensor NT outputs 12 pulses, the output speed sensor SP2 does not detect even 1 pulse.

3.

Detected 500 times consecutively.

4.

1-trip detection logic


·

Open or short in output speed sensor SP2 circuit

·

Output speed sensor SP2

·

TCM

·

Harness and connector



MONITOR DESCRIPTION

This DTC indicates that pulse is not output from the input speed sensor NT or is output only little. The input speed sensor NT terminal of the TCM detects the revolving signal from input speed sensor NT. The TCM outputs a gearshift signal comparing the input speed sensor NT with the output speed sensor SP2.

While the vehicle is operating in the shift position of D, the output shaft revolution is 300 rpm or more*, the TCM detects the trouble, illuminates the MIL and stores the DTC.

*: The engine speed is 400 rpm or more.

WIRING DIAGRAM

C250699E10
5.344,3.031 5.667,3.25 0.323,0.219 10 false TCM 0.76,2.719 1.979,2.927 1.219,0.208 10 false Transmission Wire 4.927,1.948 6.073,2.125 1.146,0.177 10 false 7 5.365,2.875 5.625,3.052 0.26,0.177 10 false A19 5.167,2.063 6.021,2.26 0.854,0.198 10 false SP2- 4.854,0.813 6,0.99 1.146,0.177 10 false 18 5.156,1.031 6.01,1.229 0.854,0.198 10 false SP2+ 2.823,0.813 3.969,0.99 1.146,0.177 10 false 1 2.823,1.948 3.969,2.125 1.146,0.177 10 false 2 0.781,2.542 0.958,2.708 0.177,0.167 10 false L3 2.354,0.813 2.75,1.01 0.396,0.198 10 false SP2+ 2.385,1.948 2.729,2.125 0.344,0.177 10 false SP2- 1.031,1.438 2.698,1.635 1.667,0.198 10 false Output Speed Sensor SP2

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch OFF.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the "Data List".

Item Measurement Item/
Range (display)
Normal Condition
SPD (SP2) Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
HINT:

Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)



HINT:
·

SPD (SP2) is always 0 while driving:

Open or short in the sensor or circuit.

·

SPD (SP2) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:

Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.INSPECT SPEED SENSOR INSTALLATION
a.
C364479E02
0.5,1.771 0.813,1.969 0.313,0.198 10 false OK 2.656,1.792 2.969,1.99 0.313,0.198 10 false NG 1.448,1.573 2.219,1.771 0.771,0.198 10 false Clearance

Check the output speed sensor SP2 installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.




OK

2.INSPECT OUTPUT SPEED SENSOR SP2

NG

SECURELY INSTALL SPEED SENSOR OR REPLACE SPEED SENSOR

2.INSPECT OUTPUT SPEED SENSOR SP2
a.

Disconnect the speed sensor connector.


b.

Perform inspection of the output speed sensor SP2 (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>INSPECTION).


c.

Connect the speed sensor connector.



OK

3.CHECK HARNESS AND CONNECTOR (OUTPUT SPEED SENSOR SP2 - TCM)

NG

REPLACE OUTPUT SPEED SENSOR SP2

3.CHECK HARNESS AND CONNECTOR (OUTPUT SPEED SENSOR SP2 - TCM)
a.

Disconnect the A19 TCM connector.


b.

Disconnect the L3 output speed sensor SP2 connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
L3-1(SP2+) - A19-18(SP2+) Always Below 1 Ω
L3-2(SP2-) - A19-7(SP2-) Always Below 1 Ω
A19-18(SP2+) - Body ground Always 10 kΩ or higher
A19-7(SP2-) - Body ground Always 10 kΩ or higher



d.

Connect the A19 TCM connector.


e.

Connect the L3 output speed sensor SP2 connector.



OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR