Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM C

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0712  Transmission Fluid Temperature Sensor "A" Circuit Low Input  P0713  Transmission Fluid Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The oil temperature sensor within the valve body detects the oil temperature within the transmission hydraulic control circuit, and inputs into the TCM a signal corresponding to the oil temperature.

C368963E01
1.563,1.948 1.771,1.365 false 0.135,0.667 0.875,0.885 0.74,0.219 10 false Resistance 1.823,1.26 2.521,1.448 0.698,0.188 10 false Acceptable 0.958,3.865 1.375,4.083 0.417,0.219 10 false Temp.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0712
1.

Not learning control prohibited status

2.

The oil temperature sensor input voltage is 0.05 V or less

3.

Detects a malfunction that continues for 10 seconds 6 times consecutively

4.

1-trip detection logic


·

Transmission wire (ATF temperature sensor)

·

Harness and connector

·

TCM


P0713
1.

Park/neutral position switch assembly is normal, and shift lever is in D or R for 1 min. or more

Not learning control prohibited status

2.

The oil temperature sensor input voltage is 4.94 V or more

3.

Detects a malfunction that continues for 1 second 12 times consecutively

4.

1-trip detection logic


·

Transmission wire (ATF temperature sensor)

·

Harness and connector

·

TCM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the automatic transmission fluid (ATF) temperature sensor circuit. The automatic transmission fluid (ATF) temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and the TCM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 0.049 V or more than 4.932 V , the TCM interprets this as a fault in the ATF sensor or wiring. The TCM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C250700E05
5.323,3.146 5.635,3.365 0.313,0.219 10 false TCM 0.708,2.833 1.969,3.01 1.26,0.177 10 false Transmission Wire 2.792,0.875 3.052,1.031 0.26,0.156 10 false 9 2.802,2.094 2.969,2.25 0.167,0.156 10 false 1 1.021,1.552 2.594,1.729 1.573,0.177 10 false ATF Temperature Sensor 4.865,0.885 5.115,1.031 0.25,0.146 10 false 22 4.875,2.094 5.115,2.26 0.24,0.167 10 false 23 5.344,3 5.646,3.167 0.302,0.167 10 false A18 5.135,2.198 5.469,2.385 0.333,0.188 10 false EOIL 5.135,1.104 5.625,1.26 0.49,0.156 10 false OIL 5.479,0.552 5.969,0.708 0.49,0.156 10 false 5V 2.469,0.875 2.958,1.031 0.49,0.156 10 false OIL 2.385,2.083 2.875,2.24 0.49,0.156 10 false EOIL 0.729,2.677 0.979,2.854 0.25,0.177 10 false L4

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the "Data List".

Item Measurement Item/
Range (display)
Normal Condition
A/T Oil Temperature 1 ATF Temp. Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
·

After Stall Test;

Approx. 80°C (176°F)

·

Equal to ambient temperature when cold soak



HINT:

When DTC P0712 is output and GTS output is -40°C (-40°F) or more, there is a short circuit.

When DTC P0713 is output and GTS output is 171°C (340°F), there is an open circuit.


Temperature Displayed Malfunction
171°C (340°F) Open circuit
-40°C (-40°F) or more Short circuit



PROCEDURE

1.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)
a.

Disconnect the A18 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A18-22(OIL) - A18-23(EOIL) Always 79 Ω to 156 kΩ



c.

Connect the A18 TCM connector.



OK

2.REPLACE TCM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the A18 TCM connector.


b.

Disconnect the L4 transmission wire connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
L4-1(EOIL) - Body ground Ignition switch ON Below 1 V
L4-9(OIL) - Body ground Ignition switch ON Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A18-22(OIL) - L4-9(OIL) Always Below 1 Ω
A18-23(EOIL) - L4-1(EOIL) Always Below 1 Ω
L4-1(EOIL) - Body ground Always 10 kΩ or higher
L4-9(OIL) - Body ground Always 10 kΩ or higher



e.

Connect the A18 TCM connector.


f.

Connect the L4 transmission wire connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR