Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2016.06
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM J

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Shift Paddle Switch Circuit  


DESCRIPTION

When the shift lever is in M, it is possible to change into any gear using the steering assembly transmission shift switch.

Additionally, when the vehicle is being driving with the shift lever in D, operating the steering assembly transmission shift switch changes to selection of gears with the shift lever in D, enabling shifting to any gear.

WIRING DIAGRAM

C259540E07
1.635,4.156 3.781,4.646 2.146,0.49 10 false To Transmission Control Switch 2.896,3.01 3.844,3.802 0.948,0.792 10 false Spiral Cable Sub-assembly 5.917,3.188 6.354,3.75 0.438,0.563 10 false TCM 5.917,3.031 6.375,3.229 0.458,0.198 10 false A19 0.958,1.115 1.396,1.323 0.438,0.208 10 false Down 1.052,1.656 1.323,1.875 0.271,0.219 10 false Up 3.979,0.99 4.281,1.167 0.302,0.177 10 false D77 2.385,0.813 2.792,1.146 0.406,0.333 10 false 1 2.396,1.365 2.917,1.854 0.521,0.49 10 false 3 4.052,0.781 4.458,0.958 0.406,0.177 10 false 8 4.052,1.354 4.573,1.573 0.521,0.219 10 false 1 5.521,0.896 5.927,1.229 0.406,0.333 10 false 1 5.521,1.469 6.042,1.958 0.521,0.49 10 false 2 0.708,3.063 1.938,3.719 1.229,0.656 10 false Transmission Shift Switch Assembly 2.406,2.396 2.563,2.573 0.156,0.177 10 false 4 4.052,2.375 4.25,2.573 0.198,0.198 10 false 2 2.365,2.583 2.823,2.781 0.458,0.198 10 false z4 5.677,0.99 6.313,1.271 0.635,0.281 10 false SFTD 5.667,1.563 6.302,1.844 0.635,0.281 10 false SFTU 3.552,0.99 3.938,1.188 0.385,0.198 10 false SDN 3.563,1.583 3.948,1.781 0.385,0.198 10 false SUP 3.563,2.583 3.948,2.781 0.385,0.198 10 false ECC 2.354,1.563 2.813,1.76 0.458,0.198 10 false z4 2.365,0.979 2.823,1.177 0.458,0.198 10 false z4 3.979,1.573 4.281,1.75 0.302,0.177 10 false D77 3.979,2.573 4.281,2.75 0.302,0.177 10 false D77

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Read the value displayed on the GTS.

OK
Tester Display Condition Standard
Sport Shift Up SW Continuously shift to "+" (upshift): ON
Release "+" (up-shift): OFF
-
Sport Shift Down SW Continuously shift to "-" (down-shift): ON
Release "-" (down-shift): OFF
-



OK

NG

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION SHIFT SWITCH ASSEMBLY - TCM)
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION SHIFT SWITCH ASSEMBLY - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A19-1(SFTD) - Body ground Pull continuously
"+"
(Up shift)
Below 1 Ω
Release "+" or "-" 10 kΩ or higher
A19-2(SFTU) - Body ground Pull continuously
"-"
(Down shift)
Below 1 Ω
Release "+" or "-" 10 kΩ or higher



c.

Connect the TCM connector.



OK

3.REPLACE TCM

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D77-2 - Body ground Always Below 1 Ω



c.

Connect the spiral cable sub-assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - TCM)
a.

Disconnect the TCM connector.


b.

Disconnect the spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A19-1(SFTD) - D77-8 Always Below 1 Ω
A19-2(SFTU) - D77-1 Always Below 1 Ω
A19-1(SFTD) or D77-8 - Body ground Always 10 kΩ or higher
A19-2(SFTU) or D77-1 - Body ground Always 10 kΩ or higher



d.

Connect the TCM connector.


e.

Connect the spiral cable sub-assembly connector.



OK

6.CHECK TRANSMISSION SHIFT SWITCH ASSEMBLY (TRANSMISSION SHIFT SWITCH ASSEMBLY - SPIRAL CABLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TRANSMISSION SHIFT SWITCH ASSEMBLY (TRANSMISSION SHIFT SWITCH ASSEMBLY - SPIRAL CABLE)
a.

Disconnect the spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z4-1 - z4-4 Pull continuously
"+"
(Up shift)
Below 1 Ω
Release "+" or "-" 10 kΩ or higher
z4-3 - z4-4 Pull continuously
"-"
(Down shift)
Below 1 Ω
Release "+" or "-" 10 kΩ or higher



c.

Connect the spiral cable sub-assembly connector.



OK

7.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY
a.

Inspect the transmission shift switch assembly (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT PADDLE SWITCH>INSPECTION).



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY