Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR
RM2090E _53 Suspension _060680 FRONT SUSPENSION _0297602 FRONT STABILIZER BAR A

FRONT SUSPENSION  FRONT STABILIZER BAR  INSTALLATION  


PROCEDURE

Hide 48815 1.INSTALL FRONT NO. 1 STABILIZER BAR BUSHING (for LH Side)

a.
C260993E03
2.75,0.479 2.625,0.479 2.625,0.479 2.24,0.688 false 1.99,0.625 2.271,0.229 2.271,0.229 2.396,0.229 false 1.792,0.573 1.656,0.24 1.656,0.24 1.583,0.24 false 0.427,1.146 0.635,1.375 0.208,0.229 10 false *a 1.375,1.146 1.604,1.375 0.229,0.229 10 false *b 2.458,0.146 2.625,0.313 0.167,0.167 10 false *d 2.823,0.406 2.979,0.542 0.156,0.135 10 false *1 1.375,0.156 1.563,0.323 0.188,0.167 10 false *c

Install the front No. 1 stabilizer bar bushing so that it is positioned closer to the outside of the vehicle than the front stabilizer bar stopper ring.

NOTICE:

Install the front No. 1 stabilizer bar bushing so that the arrow mark is facing towards the front of the vehicle.


Text in Illustration
*1 Front No. 1 Stabilizer Bar Bushing
*a Front of the Vehicle
*b Outside of the Vehicle
*c Stopper Ring
*d Arrow


Hide 48815 2.INSTALL FRONT NO. 1 STABILIZER BAR BUSHING (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 48828 3.INSTALL FRONT NO. 2 STABILIZER BRACKET LH

a.
C256604

Install the front No. 2 stabilizer bracket LH to the rear body mounting cushion sub-assembly with the bolt and nut.

Torque:
Bolt : 75 N*m (765 kgf*cm, 55 ft.*lbf)
Nut : 25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 48827 4.INSTALL FRONT NO. 2 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 52206C 5.INSTALL REAR BODY MOUNTING CUSHION SUB-ASSEMBLY LH

a.

Install the rear body mounting cushion sub-assembly LH and front stabilizer bar with the 4 new bolts.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


Hide 52205H 6.INSTALL REAR BODY MOUNTING CUSHION SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 7.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Using a hexagon wrench 6 mm, fix the stud bolt, and install the front stabilizer link assembly LH to the front stabilizer bar with a new nut.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


b.

Using a hexagon wrench 6 mm, fix the stud bolt, and install the front stabilizer link assembly LH to the front shock absorber with coil spring with a new nut.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 48820B 8.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51444B 9.INSTALL REAR ENGINE UNDER COVER LH

Hide 51443C 10.INSTALL REAR ENGINE UNDER COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 13.INSTALL FRONT WHEEL

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

Hide 15.INSPECT STEERING WHEEL CENTER POINT

Hide 16.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 18. HEIGHT CONTROL SENSOR SIGNAL INITIALIZE (w/ HID Headlight System)

Hide 19.ADJUST HEADLIGHT AIMING (w/ HID Headlight System)