Home › Suspension › REAR SUSPENSION › REAR STABILIZER BAR
RM2090E _53 Suspension _060681 REAR SUSPENSION _0297609 REAR STABILIZER BAR A

REAR SUSPENSION  REAR STABILIZER BAR  INSTALLATION  


PROCEDURE

Hide 48805A 1.INSTALL REAR STABILIZER BAR BUSHING (for LH Side)

a.
C262301E02
2.01,0.26 1.792,0.26 1.792,0.26 1.792,0.792 false 2.813,0.521 2.417,0.521 2.417,0.521 2.417,0.958 false 2.073,0.188 2.219,0.323 0.146,0.135 10 false *1 2.875,0.448 3.073,0.677 0.198,0.229 10 false *a

Install the rear stabilizer bar bushing to the outside of the stopper ring on the rear stabilizer bar as shown in the illustration.

Text in Illustration
*1 Rear Stabilizer Bar Bushing
*a Stopper Ring


Hide 48805A 2.INSTALL REAR STABILIZER BAR BUSHING (for RH Side)

HINT:

Use the same procedure described for the LH side.


Hide 48812 3.INSTALL REAR STABILIZER BAR

a.

Install the rear stabilizer bar to the rear suspension member.


Hide 48824R 4.INSTALL REAR STABILIZER BRACKET (for LH Side)

a.
C256609E02
0.229,0.188 1.344,0.302 true 0.042,0.094 0.26,0.302 0.219,0.208 10 false *a

Install the rear stabilizer bracket with the 2 bolts.

Text in Illustration
*a Crow

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the rear stabilizer bracket with its claw facing upper.



Hide 48824R 5.INSTALL REAR STABILIZER BRACKET (for RH Side)

HINT:

Use the same procedure described for the LH side.


Hide 48802 6.INSTALL STABILIZER LINK SUB-ASSEMBLY (for LH Side)

a.

Install the rear stabilizer link sub-assembly to the rear stabilizer bar


b.

Using a socket hexagon 5 mm, hold the stud bolt and tighten the nut.

Torque:
38 N*m (388 kgf*cm, 28 ft.*lbf)


c.

Temporarily install the rear stabilizer link sub-assembly to the rear No. 2 suspension arm assembly LH with the bolt and a new nut.


Hide 48802 7.INSTALL STABILIZER LINK SUB-ASSEMBLY (for RH Side)

HINT:

Use the same procedure described for the LH side.


Hide 89408C 8.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ HID Headlight System)

Hide 9.INSTALL REAR WHEELS

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

Hide 10.STABILIZE SUSPENSION

Hide 48802 11.FULLY TIGHTEN STABILIZER LINK SUB-ASSEMBLY (for LH Side)

a.

Install the rear stabilizer link sub-assembly to the rear No. 2 suspension arm assembly LH with the bolt and nut.

Torque:
38 N*m (388 kgf*cm, 28 ft.*lbf)


Hide 48802 12.FULLY TIGHTEN STABILIZER LINK SUB-ASSEMBLY (for RH Side)

HINT:

Use the same procedure described for the LH side.


Hide 13.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 15. HEIGHT CONTROL SENSOR SIGNAL INITIALIZE (w/ HID Headlight System)

Hide 16.ADJUST HEADLIGHT AIMING (w/ HID Headlight System)