Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C146E  Open in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay is built into the skid control ECU in the brake actuator assembly.

The ABS solenoid relay supplies power to the ABS and TRC solenoids.

The skid control ECU detects a solenoid relay malfunction by performing a self check and relay operation check.

DTC No. DTC Detection Condition Trouble Area
C146E Either of the following is detected:
1.

A solenoid relay drive circuit in the skid control ECU is malfunctioning.

2.

The solenoid relay cannot be switched between on and off.


·

ABS NO. 2 fuse (Fusible link block assembly)

·

ABS solenoid relay circuit

·

Skid control ECU



WIRING DIAGRAM

C261877E02
1.531,1.094 2.375,1.573 0.844,0.479 10 false ABS NO. 2 4.302,8.25 4.646,8.49 0.344,0.24 10 false A5 3.177,0.833 3.719,1.188 0.542,0.354 10 false 25 3.177,4.979 3.531,5.26 0.354,0.281 10 false 38 0.646,6.854 1.292,7.104 0.646,0.25 10 false Battery 3.448,4.979 4.042,5.323 0.594,0.344 10 false GND1 3.427,0.833 3.938,1.156 0.51,0.323 10 false +BS 4.375,4.281 5.521,4.458 1.146,0.177 10 false Skid Control ECU 4.313,8.406 6,8.635 1.688,0.229 10 false Brake Actuator Assembly 4.281,0.927 5.583,1.25 1.302,0.323 10 false ABS Solenoid Relay 5.875,2.188 6.281,2.333 0.406,0.146 10 false SFRH 5.875,2.688 6.281,2.865 0.406,0.177 10 false SFLH 5.875,3.188 6.302,3.354 0.427,0.167 10 false SRRH 5.875,3.667 6.302,3.833 0.427,0.167 10 false SRLH 5.875,4.177 6.333,4.448 0.458,0.271 10 false SFRR 5.875,4.677 6.323,4.906 0.448,0.229 10 false SFLR 5.875,5.167 6.365,5.396 0.49,0.229 10 false SRRR 5.885,5.656 6.354,5.875 0.469,0.219 10 false SRLR 5.885,6.177 6.365,6.375 0.479,0.198 10 false SRM1 5.875,6.677 6.333,6.875 0.458,0.198 10 false SRM2 5.896,7.188 6.333,7.385 0.438,0.198 10 false SRC1 5.896,7.667 6.458,7.865 0.563,0.198 10 false SRC2 0.552,3.958 1.188,4.219 0.635,0.26 10 false ALT

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When C1241 is output together with C146E, inspect and repair the trouble areas indicated by C1241 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
U147143E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 0.655,0.47 0.655,0.867 false 0.503,0.289 0.819,0.440 0.317,0.151 10 +BS 1.598,0.198 1.905,0.348 0.307,0.151 10 A5

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-25 (+BS) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U147144E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 2.742,0.487 2.742,0.862 false 2.518,0.314 2.984,0.465 0.467,0.151 10 GND1 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-38 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

3.RECONFIRM DTC
HINT:

This DTC is stored when a problem is identified in the skid control ECU (brake actuator assembly).

The solenoid circuits are located in the brake actuator assembly.

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the skid control ECU (brake actuator assembly).


a.

Reconnect the skid control ECU (brake actuator assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for 30 seconds or more.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C146E is not output. A
DTC C146E is output. B


HINT:
·

If a speed signal of 15 km/h (9 mph) or more is received by the skid control ECU (brake actuator assembly) with the ignition switch ON, the skid control ECU (brake actuator assembly) performs self diagnosis of the solenoid circuit.

·

If the normal system code is output (No DTCs are output), slightly jiggle the connectors, wire harnesses, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B