Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C146C  Open in ABS Motor Relay Circuit  


DESCRIPTION

The ABS motor relay supplies power to the pump motor. While the ABS is activated, the skid control ECU turns the ABS motor relay on to operate the pump motor.

If the voltage supplied to the ABS motor relay (+BM) is too low due to low voltage from the battery or alternator, the DTC may be stored.

DTC No. DTC Detection Condition Trouble Area
C146C Any of the following is detected:
1.

When the ABS motor relay is actuated, voltage is not supplied to the pump motor.

2.

When the ABS motor relay is not actuated, voltage in the pump motor is high.

3.

The skid control ECU judges that pump motor operation is abnormal.


·

ABS NO. 1 fuse (Fusible link block assembly)

·

ABS motor relay circuit

·

ABS motor relay (Brake actuator assembly)



WIRING DIAGRAM

C261876E01
0.732,3.999 1.221,4.169 0.489,0.170 10 Battery 1.698,2.155 2.509,2.426 0.810,0.271 10 ABS NO. 1 3.444,1.894 3.640,2.043 0.196,0.149 10 1 3.647,1.894 3.957,2.041 0.310,0.147 10 +BM 4.317,5.166 5.970,5.331 1.654,0.165 10 Brake Actuator Assembly 4.603,0.812 5.722,0.968 1.119,0.156 10 Skid Control ECU 4.611,1.999 5.706,2.159 1.096,0.161 10 ABS Motor Relay 4.787,3.72 5.591,3.881 0.804,0.161 10 Pump Motor 4.317,5.026 4.583,5.175 0.266,0.149 10 A5 3.388,3.386 3.584,3.535 0.196,0.149 10 13 3.647,3.386 4.058,3.532 0.410,0.147 10 GND2 0.634,2.771 1.346,2.945 0.713,0.174 10 ALT

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When C1241 is output together with C146C, inspect and repair the trouble areas indicated by C1241 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241).


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Active Test using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard


d.

Check the operating sound of the pump motor when operating it using the GTS.

Result:
Result Proceed to
Operating sound is heard. A
Operating sound is not heard. B




A

2.RECONFIRM DTC

B

3.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
2.RECONFIRM DTC
HINT:

This DTC is stored when a problem is identified in the brake actuator assembly.

The ABS motor relay is in the brake actuator assembly.

Therefore, motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the skid control ECU (brake actuator assembly).



b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for 30 seconds or more.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C146C is not output. A
DTC C146C is output. B


HINT:
·

If a speed signal of 40 km/h (25 mph) or more is received by the skid control ECU (brake actuator assembly) with the ignition switch ON, the skid control ECU (brake actuator assembly) performs self diagnosis of the motor circuit.

·

If the normal system code is output (No DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B

3.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)
a.
U147141E01
0.073,0.065 0.239,0.215 0.166,0.151 10 *a 0.706,1.407 0.706,1.818 false 0.554,1.831 0.966,1.982 0.411,0.151 10 +BM 1.598,0.179 1.854,0.330 0.256,0.151 10 A5

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-1 (+BM) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
U147142E01
0.074,0.065 0.240,0.215 0.166,0.151 10 *a 1.599,0.179 1.855,0.330 0.256,0.151 10 A5 2.701,1.407 2.701,1.818 false 2.467,1.831 2.907,1.982 0.439,0.151 10 GND2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-13 (GND2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)