Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM2090E _55 Steering _060690 STEERING COLUMN _0297644 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2781  Open / Short in Steering Lock ECU  


DESCRIPTION

The steering lock ECU and steering lock motor are built into the steering lock actuator assembly.

The steering lock ECU detects whether the steering lock is in the lock or unlock position by using the lock position sensor of the steering lock motor.

The steering lock ECU receives lock and unlock command signals from the certification ECU (smart key ECU assembly) and responds with lock and unlock operation signals.

HINT:

The steering lock actuator assembly (steering lock ECU) is not connected to the CAN communication system. However, the steering lock actuator assembly (steering lock ECU) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).


DTC No. Detection Condition Trouble Area DTC Output Confirmation Operation
B2781 One of the following conditions is met (1-trip detection logic*1):
·

The steering lock/unlock position sensor is malfunctioning*2.

·

The steering lock motor activation circuit has a short circuit.

·

The steering lock motor activation circuit has an open circuit.


·

Steering lock actuator assembly (steering lock ECU)

·

LIN communication system


No confirmation operation is necessary (monitoring is continuous).

*1: Only output while a malfunction is present and the engine switch is on (IG).

*2: When both detection switches turn on, the system is determined to be malfunctioning.


U113991E02
2.094,2.385 2.802,1.969 2.802,1.969 4.156,1.969 false 3.521,1.708 3.854,1.969 false 0.24,3.542 0.677,3.542 false 0.885,1.198 1.219,1.375 0.333,0.177 10 false ON 0.885,1.5 1.219,1.677 0.333,0.177 10 false OFF 0.885,2.375 1.219,2.552 0.333,0.177 10 false ON 0.885,2.708 1.219,2.885 0.333,0.177 10 false OFF 0.156,0.719 0.969,1.094 0.813,0.375 10 false Unlock Sensor 0.156,1.979 0.813,2.313 0.656,0.333 10 false Lock Sensor 1.594,3.073 3.667,3.26 2.073,0.188 10 false Lock operation conditions met 4.104,3.083 6.396,3.26 2.292,0.177 10 false Unlock operation conditions met 4.229,1.885 5.208,2.198 0.979,0.313 10 false Example of Malfunction 0.719,3.469 2.938,3.667 2.219,0.198 10 false : Normal operation

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. Prohibits the engine from being started (the engine does not crank).

Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2781
Entry&Start
·

Sensor Value

·

Power Supply Short


-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off (lock), perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins, or 2) connect the GTS to the vehicle and select "Manual" from the initial screen on the GTS. Select "Key Code Registration" under model code.

·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the steering lock actuator assembly (steering lock ECU), refer to the Service Bulletin.

·

After performing repairs, confirm that no DTCs are output again.



HINT:

When all the ECUs that are connected to the LIN communication cannot communicate with the certification ECU (smart key ECU assembly), DTC B2785 is stored.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Using the GTS, check if LIN communication DTC B2785 is output (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

HINT:

If a LIN communication DTC is output, perform troubleshooting for the LIN communication system (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


Result
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B



A

GO TO LIN COMMUNICATION SYSTEM (DTC B2785)

B

REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)