Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM2090E _56 Audio / Visual / Telematics _060692 AUDIO / VIDEO _0297650 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK RADIO RECEIVER ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop A
Automatic station search function stops on a station B





A

2.CHECK OPTIONAL COMPONENTS

B

REPLACE RADIO RECEIVER ASSEMBLY

2.CHECK OPTIONAL COMPONENTS
a.

Check if the telephone antenna or other optional components are installed.

Result:
Result Proceed to
Optional components are not installed A
Optional components are installed B


NOTICE:

Do not remove optional components without the permission of the customer.




A

3.CHECK RADIO RECEIVER ASSEMBLY

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO RECEIVER ASSEMBLY
a.
E187251

Preparation for check

i.

Remove the antenna connector from the radio receiver assembly.



b.

Check for noise

i.

Turn the ignition switch ACC with the radio receiver assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.





OK

4.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

4.INSPECT RADIO RECEIVER ASSEMBLY
a.

Disconnect the radio receiver assembly connector.


b.
U190416E02
1.542,1.104 1.135,1.458 true 0.177,0.104 0.354,0.271 0.177,0.167 10 false *a 0.74,1.063 0.958,1.25 0.219,0.188 10 false RA 0.833,1.479 1.229,1.646 0.396,0.167 10 false ANT+

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and FM or AM selected
11 to 14 V


Text in Illustration
*a Component without harness connected
(Radio Receiver Assembly)



OK

5.REPLACE ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

5.REPLACE ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

NORMAL OPERATION

NG

6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
6.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the No. 2 antenna cord sub-assembly.


b.

Measure the resistance the No. 2 antenna cord sub-assembly to check for an open circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

Below 1 Ω



c.

Measure the resistance between the No. 2 antenna cord sub-assembly and body ground to check for a short circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

10 kΩ or higher




OK

7.REPLACE AMPLIFIER ANTENNA ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.REPLACE AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly and check if radio broadcasts can be received normally.

OK:

Radio broadcasts can be received normally.




OK

NORMAL OPERATION

NG

REPLACE RADIO RECEIVER ASSEMBLY