Home › Power Source / Network › FA20 (BATTERY / CHARGING) › CHARGING SYSTEM (for 130 A Type)
RM2090E _57 Power Source / Network _060693 FA20 BATTERY / CHARGING _0297661 CHARGING SYSTEM(for 130 A Type) C

FA20 BATTERY / CHARGING  CHARGING SYSTEM(for 130 A Type)  P0516  Battery Temperature Sensor Circuit Low  P0517  Battery Temperature Sensor Circuit High  


DESCRIPTION

A283631E03
1.646,3.01 2.198,3.271 0.552,0.26 10 false °C (°F) 0.167,0.323 1.26,0.531 1.094,0.208 10 false Resistance (kΩ) 1.188,2.365 1.365,2.542 0.177,0.177 10 false 0 1.51,2.531 1.76,2.729 0.25,0.198 10 false 20 0.24,1.927 0.5,2.115 0.26,0.188 10 false 10 0.24,1.625 0.479,1.813 0.24,0.188 10 false 20 0.24,1.333 0.51,1.531 0.271,0.198 10 false 30 0.24,1.031 0.542,1.24 0.302,0.208 10 false 40 0.24,0.74 0.531,0.927 0.292,0.188 10 false 50 0.313,2.24 0.49,2.427 0.177,0.188 10 false 0 1.875,2.354 2.146,2.552 0.271,0.198 10 false 40 2.24,2.542 2.479,2.781 0.24,0.24 10 false 60 2.615,2.354 2.865,2.542 0.25,0.188 10 false 80 2.927,2.542 3.271,2.74 0.344,0.198 10 false 100 0.74,2.521 1.052,2.719 0.313,0.198 10 false -20 0.375,2.354 0.708,2.552 0.333,0.198 10 false -40 0.333,2.51 0.667,2.708 0.333,0.198 10 false (-40) 0.74,2.677 1.052,2.875 0.313,0.198 10 false (-4) 1.115,2.51 1.427,2.688 0.313,0.177 10 false (32) 1.469,2.688 1.719,2.885 0.25,0.198 10 false (68) 1.813,2.531 2.167,2.74 0.354,0.208 10 false (104) 2.156,2.698 2.5,2.938 0.344,0.24 10 false (140) 2.531,2.542 2.958,2.781 0.427,0.24 10 false (176) 2.896,2.708 3.24,2.917 0.344,0.208 10 false (212)

The battery temperature sensor installed on the battery current sensor assembly detects the battery temperature.

A thermistor is integrated into the battery temperature sensor, and the resistance in the battery temperature sensor changes according to the battery temperature.

The resistance of the thermistor in the battery temperature sensor decreases as the battery temperature increases. The resistance increases as the temperature decreases.

The battery temperature sensor is connected to the ECM. The ECM supplies 5 V from the THB terminal to the battery temperature sensor through resistor R.

The battery temperature sensor and resistor R are connected in series. This results in fluctuations in the voltage supplied from the THB terminal when the resistance changes according to the battery temperature.

The ECM determines the battery temperature according to fluctuations in voltage. When the battery temperature is high, the ECM determines to reduce the amount of current supplied from the generator in order to protect the battery.

DTC No. DTC Detection Condition Trouble Area
P0516
·

Engine speed is 500 r/min or more, battery voltage is 10.9 V or more, and 1 second or more have elapsed after starting.

·

Battery temperature sensor output is less than 0.104 V, and duration of the malfunction is 0.5 seconds or more (1-trip detection logic).


·

Battery current sensor assembly (battery temperature sensor)

·

Short to GND in battery temperature sensor circuit

·

ECM


P0517
·

Engine speed is 500 r/min or more, battery voltage is 10.9 V or more, and 1 second or more have elapsed after starting.

·

Battery temperature sensor output is more than 4.867 V, and duration of the malfunction is 0.5 seconds or more (1-trip detection logic).


·

Battery current sensor assembly (battery temperature sensor)

·

Open in battery temperature sensor circuit

·

ECM



WIRING DIAGRAM

B268674E05
0.271,3.229 3.479,3.563 3.208,0.333 10 false BATTERY CURRENT SENSOR ASSEMBLY 0.958,1.677 1.969,1.854 1.01,0.177 10 false Current Sensor 0.833,2.396 2.115,2.604 1.281,0.208 10 false Temperature Sensor 2.146,0.74 2.469,0.917 0.323,0.177 10 false VIN 2.25,1.302 2.427,1.458 0.177,0.156 10 false IB 2.135,2.063 2.552,2.292 0.417,0.229 10 false THB 2.115,2.542 2.458,2.75 0.344,0.208 10 false GND 2.5,2.063 2.75,2.292 0.25,0.229 10 false 2 2.5,1.292 2.594,1.438 0.094,0.146 10 false 4 2.5,0.74 2.594,0.885 0.094,0.146 10 false 1 2.5,2.542 2.594,2.688 0.094,0.146 10 false 3 5.344,3.031 5.729,3.333 0.385,0.302 10 false ECM 5.385,0.844 5.865,1 0.479,0.156 10 false VCP2 5.406,1.406 5.667,1.604 0.26,0.198 10 false IB 5.385,2.177 5.813,2.438 0.427,0.26 10 false THB 5.396,2.646 5.938,2.823 0.542,0.177 10 false EPA2 5.094,0.667 5.385,0.844 0.292,0.177 10 false 22 5.094,1.229 5.313,1.396 0.219,0.167 10 false 11 5.094,2 5.375,2.219 0.281,0.219 10 false 24 5.094,2.469 5.396,2.667 0.302,0.198 10 false 30 5.052,0.844 5.406,1.042 0.354,0.198 10 false A35 5.052,1.396 5.448,1.615 0.396,0.219 10 false A33 5.052,2.188 5.406,2.396 0.354,0.208 10 false A33 5.052,2.656 5.427,2.854 0.375,0.198 10 false A35 0.281,3.063 0.656,3.24 0.375,0.177 10 false A11

PROCEDURE

1.INSPECT BATTERY CURRENT SENSOR ASSEMBLY
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A266305E05
1.906,1.26 2.198,1.802 true 1.531,1.271 1.24,1.813 true 0.115,0.094 0.281,0.24 0.167,0.146 10 false *a 2.26,1.802 2.552,1.958 0.292,0.156 10 false THB 0.917,1.802 1.323,1.958 0.406,0.156 10 false GND

Disconnect the A11 battery current sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (THB) - 3 (GND) 20 to 30°C (68 to 86°F) 1.5 to 2.6 kΩ


Text in Illustration
*a Component without harness connected
(Battery Current Sensor Assembly)


d.

Reconnect the cable to the negative (-) battery terminal.



OK

2.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR ASSEMBLY - ECM)

NG

REPLACE BATTERY CURRENT SENSOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR ASSEMBLY - ECM)
a.

Disconnect the A33 and A35 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A33-24 (THB) - A11-2 (THB) Always Below 1 Ω
A35-30 (EPA2) - A11-3 (GND) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A33-24 (THB) or A11-2 (THB) - Body ground Always 10 kΩ or higher
A35-30 (EPA2) or A11-3 (GND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR