Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297665 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in CAN Main Bus Line (RHD Models)  


DESCRIPTION

There may be an open circuit one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 64 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 64 Ω or higher.
·

DLC3 branch line or connector

·

CAN main bus line or connector

·

ECM

·

Skid control ECU

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector



This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensor connected a CAN main bus branch.

WIRING DIAGRAM

C261302E02
1.865,0.292 2.188,0.469 0.323,0.177 10 false ECM 0.26,1.896 2.26,2.073 2,0.177 10 false NO. 1 JUNCTION CONNECTOR 5.01,0.156 6.854,0.344 1.844,0.188 10 false : CAN Main Bus Line (CANH) 5.01,0.531 6.802,0.719 1.792,0.188 10 false : CAN Main Bus Line (CANL) 0.271,1.719 0.563,1.885 0.292,0.167 10 false A17 0.26,4.656 2.24,4.823 1.979,0.167 10 false NO. 2 JUNCTION CONNECTOR 0.26,4.479 0.552,4.656 0.292,0.177 10 false D43 1.865,0.125 2.156,0.281 0.292,0.156 10 false A33 2.771,0.896 2.948,1.073 0.177,0.177 10 false 18 2.521,0.646 2.896,0.823 0.375,0.177 10 false CANL 3.833,0.646 4.24,0.802 0.406,0.156 10 false CANH 2.531,7.406 2.896,7.573 0.365,0.167 10 false CANL 3.833,7.417 4.25,7.594 0.417,0.177 10 false CANH 5.5,5.438 5.885,5.604 0.385,0.167 10 false CANL 5.49,5.177 5.917,5.344 0.427,0.167 10 false CANH 3.792,0.896 3.969,1.063 0.177,0.167 10 false 19 3.833,1.521 3.979,1.667 0.146,0.146 10 false 7 2.771,1.521 2.938,1.677 0.167,0.156 10 false 18 3.854,1.198 3.979,1.375 0.125,0.177 10 false O 2.646,1.188 2.906,1.354 0.26,0.167 10 false B-P 3.833,3.448 3.979,3.615 0.146,0.167 10 false 6 2.729,3.448 2.906,3.615 0.177,0.167 10 false 17 3.833,4.354 3.958,4.521 0.125,0.167 10 false 9 2.781,4.354 2.979,4.521 0.198,0.167 10 false 20 3.833,3.625 4.156,3.781 0.323,0.156 10 false W-B 2.656,3.625 2.917,3.781 0.26,0.156 10 false R-Y 3.865,4.135 4.021,4.313 0.156,0.177 10 false O 2.656,4.125 2.927,4.281 0.271,0.156 10 false B-P 0.125,7.896 1.302,8.083 1.177,0.188 10 false x: Suspected Area 3.177,0.104 3.563,0.271 0.385,0.167 10 false 120Ω 3.833,6.271 3.958,6.438 0.125,0.167 10 false 1 2.74,6.26 2.906,6.417 0.167,0.156 10 false 12 3.885,7.208 4.063,7.365 0.177,0.156 10 false 26 2.75,7.219 2.938,7.385 0.188,0.167 10 false 14 3.854,6.448 4.156,6.615 0.302,0.167 10 false W-B 2.667,6.448 2.917,6.615 0.25,0.167 10 false R-Y 3.875,6.979 4.104,7.146 0.229,0.167 10 false BR 2.667,7 2.906,7.167 0.24,0.167 10 false B-R 4.438,7.427 4.646,7.604 0.208,0.177 10 false A5 4.438,7.594 6.365,7.958 1.927,0.365 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 3.208,8.01 3.594,8.177 0.385,0.167 10 false 120Ω 5.01,0.927 6.948,1.115 1.938,0.188 10 false : CAN Branch Bus Line (CANH) 5.01,1.302 6.938,1.479 1.927,0.177 10 false : CAN Branch Bus Line (CANL) 5.542,5.917 5.906,6.094 0.365,0.177 10 false DLC3 5.542,5.75 5.813,5.917 0.271,0.167 10 false D10 5.167,5.104 5.302,5.271 0.135,0.167 10 false 6 4.375,5.052 4.479,5.229 0.104,0.177 10 false 5 4.802,5.021 5.063,5.177 0.26,0.156 10 false B-Y 4.844,5.625 5.052,5.792 0.208,0.167 10 false LG 4.333,5.563 4.51,5.719 0.177,0.156 10 false 16 5.26,5.542 5.427,5.708 0.167,0.167 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds,

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U147249E04
2.271,0.365 1.979,0.896 true 1.896,1.49 1.604,2.031 true 1.49,0.354 1.781,0.51 0.292,0.156 10 false D10 0.083,0.063 0.25,0.229 0.167,0.167 10 false *1 2.323,0.26 2.74,0.417 0.417,0.156 10 false CANH 1.188,1.948 1.583,2.104 0.396,0.156 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D10-6 (CANH) - D10-14 (CANL) Cable disconnected from negative (-) battery terminal 114 to 126 Ω


Text in Illustration
*1 DLC3

NOTICE:

When the measured value is 127 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).




OK

2.CHECK FOR OPEN IN CAN BUS LINES (ECM)

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR OPEN IN CAN BUS LINES (ECM)
a.
U147053E02
1.198,1.51 1.49,2.042 true 0.958,1.51 0.667,2.042 true 1.563,0.313 1.875,0.479 0.313,0.167 10 false A33 0.094,0.042 0.292,0.219 0.198,0.177 10 false *a 1.573,1.969 2,2.125 0.427,0.156 10 false CANH 0.26,1.969 0.625,2.115 0.365,0.146 10 false CANL

Disconnect the A33 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-19 (CANH) - A33-18 (CANL) Cable disconnected from negative (-) battery terminal 114 to 126 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

3.CHECK FOR OPEN IN CAN BUS LINES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
3.CHECK FOR OPEN IN CAN BUS LINES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Reconnect the A33 ECM connector.


b.
U147125E04
1.292,0.802 0.99,1.115 true 1.188,1.615 0.906,1.344 true 0.188,1.083 0.406,1.25 0.219,0.167 10 false A5 1.323,0.656 1.729,0.813 0.406,0.156 10 false CANL 1.219,1.563 1.646,1.708 0.427,0.146 10 false CANH 0.177,0.052 0.333,0.229 0.156,0.177 10 false *a

Disconnect the A5 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-26 (CANH) - A5-14 (CANL) Cable disconnected from negative (-) battery terminal 114 to 126 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

NG

4.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 2 J/C)
4.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 2 J/C)
a.

Reconnect the A5 skid control ECU (brake actuator assembly) connector.


b.
U147048E03
0.74,1.521 0.479,1.26 true 0.469,2.167 0.729,1.906 true 2.896,0.927 2.281,1.531 true 2.292,1.906 2.906,2.51 true 1.563,0.531 1.854,0.688 0.292,0.156 10 false D43 0.104,0.052 0.271,0.229 0.167,0.177 10 false *a 0.25,1.146 0.438,1.313 0.188,0.167 10 false *b 0.271,2.125 0.448,2.302 0.177,0.177 10 false *b 2.948,0.802 3.125,0.979 0.177,0.177 10 false *c 2.948,2.469 3.125,2.646 0.177,0.177 10 false *c

Disconnect the wire harness connector from the D43 CAN No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
D43-1 - D43-12 Cable disconnected from negative (-) battery terminal 114 to 126 Ω skid control ECU (brake actuator assembly)
D43-9 - D43-20 Cable disconnected from negative (-) battery terminal 114 to 126 Ω CAN No. 1 junction connector


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Skid Control ECU (Brake Actuator Assembly)
*c to CAN No. 1 Junction Connector

Result:
Result Proceed to
OK A
NG (CAN No. 1 junction connector main line) B
NG (skid control ECU (brake actuator assembly) main line) C




A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

5.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 2 J/C - CAN NO. 1 J/C)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

5.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 2 J/C - CAN NO. 1 J/C)
a.

Reconnect the wire harness connector to the D43 CAN No. 2 junction connector.


b.
U147049E03
2.448,0.781 1.729,1.51 true 1.74,1.885 2.448,2.604 true 1.542,0.531 1.833,0.688 0.292,0.156 10 false A17 0.104,0.052 0.281,0.24 0.177,0.188 10 false *a 2.49,0.667 2.667,0.844 0.177,0.177 10 false *b 2.49,2.583 2.677,2.75 0.188,0.167 10 false *b

Disconnect the wire harness connector from the A17 CAN No. 1 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-6 - A17-17 Cable disconnected from negative (-) battery terminal 114 to 126 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 2 Junction Connector



OK

6.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 1 J/C - ECM)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C)

6.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 1 J/C - ECM)
U147050E03
2.625,0.781 1.906,1.51 true 1.927,1.896 2.635,2.615 true 1.552,0.531 1.844,0.688 0.292,0.156 10 false A17 0.104,0.052 0.271,0.24 0.167,0.188 10 false *a 2.677,0.677 2.875,0.854 0.198,0.177 10 false *b 2.698,2.573 2.885,2.76 0.188,0.188 10 false *b

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-7 - A17-18 Cable disconnected from negative (-) battery terminal 114 to 126 Ω


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM



OK

REPLACE CAN NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - ECM)