Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U190184E02
4.865,0.771 5.146,0.917 0.281,0.146 10 false D41 3.292,0.771 3.573,0.917 0.281,0.146 10 false D40 1.917,0.771 2.208,0.917 0.292,0.146 10 false D48

a.

Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
D48-2 (+B) - D48-11 (GND) Input R - B +B power supply Always 9.5 to 16 V -
D48-11 (GND) - Body ground - B - Body ground Ground Always Below 1 Ω -

If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.


c.

Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage according to the value(s) in the table below.

HINT:
·

Check that the entry cancel function, which is one of the customizing settings of the entry and start system, is not set (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS).

·

Check that the customizing setting "Ignition Available Area" of entry and start system is All (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS).



Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
D41-5 (IG2) - D48-11 (GND) Input Y - B IG power supply Engine switch off → on (IG) Below 1 V → 11 to 14 V Ignition Switch
D41-12 (CLG1) - D48-11 (GND) Output Y - B Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
D41-13 (CG1B) - D48-11 (GND) Output BR - B Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
D41-11 (CLG2) - D48-11 (GND) Output P - B Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Passenger Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
D41-10 (CG2B) - D48-11 (GND) Output V - B Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
D41-3 (CLG5) - D48-11 (GND) Output BE - B Output to indoor electrical key oscillator (front floor) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
D41-2 (CG5B) - D48-11 (GND) Output P - B Output to indoor electrical key oscillator (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
D41-20 (TSW1) - D48-11 (GND) Input G - B Driver door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


Pulse generation (See waveform 4) D-Door Trigger Switch
D41-8 (TSW2) - D48-11 (GND) Input L - B Front passenger door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched


Pulse generation (See waveform 4) P-Door Trigger Switch
D41-22 (SEN1) - D48-11 (GND) Input L - B Driver door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched


Pulse generation (See waveform 4) D-Door Touch Sensor
D41-23 (SEN2) - D48-11 (GND) Input W - B Front passenger door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched


Pulse generation (See waveform 4) P-Door Touch Sensor
D40-27 (TSW5) - D48-11 (GND) Input Y - B Back door opener switch signal input Back door opener switch assembly off → on Pulse generation (See waveform 4) Tr/B-Door Unlock SW
D40-11 (CLG6) - D48-11 (GND) Output W - B Output to No. 2 indoor electrical key oscillator (rear floor) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
D40-10 (CG6B) - D48-11 (GND) Output B - B Output to No. 2 indoor electrical key oscillator (rear floor) (terminal on opposite side of component from CLG6 output terminal) Proceed:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
D40-9 (CLG7) - D48-11 (GND) Output W - B Output to No. 3 indoor electrical key oscillator (inside luggage compartment) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Luggage (inside) (key diagnostic mode)
D40-8 (CG7B) - D48-11 (GND) Output R - B Output to No. 3 indoor electrical key oscillator (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) Proceed:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Luggage (inside) (key diagnostic mode)
D41-19 (POS1) - D48-11 (GND) Output V - B Driver door unlock sensor power source (12 V (drops when engine switch turned on (IG))) Engine switch off → on (IG) 9 to 14 V → Below 2 V -
D41-21 (POS2) - D48-11 (GND) Output R - B Front passenger door unlock sensor power source (12 V (drops when engine switch turned on (IG))) Engine switch off → on (IG) 9 to 14 V → Below 2 V -
D40-5 (RCO) - D48-11 (GND) Output LG - B Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 5) -
D40-17 (RDA) - D48-11 (GND) Input P - B Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). Proceed:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 6) -
D40-19 (RSSI) - D48-11 (GND) Input R - B Communication channel switching circuit. Proceed:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 7) -
D40-2 (CLG8) - D48-11 (GND) Output BR - B Output to electrical key antenna (outside luggage) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation (See waveform 8) Over Head + Luggage
or
Luggage + Luggage (key diagnostic mode)
D40-1 (CG8B) - D48-11 (GND) Output Y - B Output to electrical key antenna (outside luggage) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation (See waveform 8) Over Head + Luggage
or
Luggage + Luggage (key diagnostic mode)

*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*3: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK).



e.
B251021E20
0.135,1.01 0.469,1.208 0.333,0.198 10 false GND

Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection
·

D41-12 (CLG1) - D48-11 (GND)

·

D41-11 (CLG2) - D48-11 (GND)


Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).



f.
B251024E19
0.146,1.042 0.479,1.24 0.333,0.198 10 false GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection
·

D41-12 (CLG1) - D48-11 (GND)

·

D41-11 (CLG2) - D48-11 (GND)


Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).


Waveform 2 (Reference)
Item Content
Tester Connection
·

D41-13 (CG1B) - D48-11 (GND)

·

D41-10 (CG2B) - D48-11 (GND)


Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

All doors locked through wireless operation



*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).



g.
B251020E14
0.854,1.885 1.042,2.094 0.188,0.208 10 false *a 1.76,1.896 1.948,2.104 0.188,0.208 10 false *b 0.146,1 0.479,1.198 0.333,0.198 10 false GND

Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Door open
*b After approximately 30 seconds from when the door is closed

Waveform 3 (Reference)
Item Content
Tester Connection
·

D41-3 (CLG5) - D48-11 (GND)

·

D41-2 (CG5B) - D48-11 (GND)

·

D40-11 (CLG6) - D48-11 (GND)

·

D40-10 (CG6B) - D48-11 (GND)

·

D40-9 (CLG7) - D48-11 (GND)

·

D40-8 (CG7B) - D48-11 (GND)


Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds




h.
B251023E28
1.354,0.49 1.99,0.104 1.99,0.104 2.208,0.104 false 1.99,0.115 1.76,0.49 false 0.167,1.198 0.5,1.354 0.333,0.156 10 false GND 2.25,0.063 2.406,0.24 0.156,0.177 10 false *a

Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a In actuality, sampling is being performed

Waveform 4 (Reference)
Item Content
Tester Connection D41-20 (TSW1) - D48-11 (GND)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched



Waveform 4 (Reference)
Item Content
Tester Connection D41-8 (TSW2) - D48-11 (GND)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched



Waveform 4 (Reference)
Item Content
Tester Connection D41-22 (SEN1) - D48-11 (GND)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched



Waveform 4 (Reference)
Item Content
Tester Connection D41-23 (SEN2) - D48-11 (GND)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched



Waveform 4 (Reference)
Item Content
Tester Connection D40-27 (TSW5) - D48-11 (GND)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Back door opener switch assembly off → on


i.
B251178E01
0.103,0.984 0.433,1.178 0.330,0.194 10 GND 0.97,1.886 1.153,2.044 0.183,0.158 10 *a 2.01,1.886 2.192,2.044 0.183,0.158 10 *b

Using an oscilloscope, check waveform 5.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed

Waveform 5 (Reference)
Item Content
Tester Connection D40-5 (RCO) - D48-11 (GND)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK).



j.
B251177E01
0.103,0.984 0.433,1.178 0.330,0.194 10 GND 0.984,1.878 1.167,2.037 0.183,0.158 10 *a 2.2,1.878 2.383,2.037 0.183,0.158 10 *b

Using an oscilloscope, check waveform 6.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed

Waveform 6 (Reference)
Item Content
Tester Connection D40-17 (RDA) - D48-11 (GND)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Proceed:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK).



k.
B251070E03
0.177,1.01 0.51,1.208 0.333,0.198 10 false GND 1.115,1.896 1.302,2.052 0.188,0.156 10 false *a 2.063,1.896 2.25,2.052 0.188,0.156 10 false *b

Using an oscilloscope, check waveform 7.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed

Waveform 7 (Reference)
Item Content
Tester Connection D40-19 (RSSI) - D48-11 (GND)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Proceed:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK).



l.
B265917E01
0.106,1.007 0.432,1.146 0.326,0.139 10 GND 1.189,1.97 1.342,2.108 0.153,0.139 10 *a

Using an oscilloscope, check waveform 8.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Engine switch off, all doors closed and back door opener switch assembly off → on

Waveform 8 (Reference)
Item Content
Tester Connection
·

D40-2 (CLG8) - D48-11 (GND)

·

D40-1 (CG8B) - D48-11 (GND)


Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on





CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)


U146875E04
1.667,6.75 1.854,6.906 0.188,0.156 10 false *2 0.323,0.177 0.51,0.333 0.188,0.156 10 false *1 3.438,3.188 3.667,3.344 0.229,0.156 10 false MB 3.74,0.969 3.979,1.125 0.24,0.156 10 false MB 0.896,1.823 1.104,1.979 0.208,0.156 10 false 3C 0.885,1.167 1.073,1.333 0.188,0.167 10 false 3D 1.063,2.396 1.26,2.563 0.198,0.167 10 false 3E 5.854,1.833 6.052,2.01 0.198,0.177 10 false 3A 5.865,1.156 6.083,1.313 0.219,0.156 10 false 3B 6.25,4.052 6.479,4.208 0.229,0.156 10 false 3E 4.188,4.073 4.417,4.229 0.229,0.156 10 false 3C 1.427,4.073 1.656,4.229 0.229,0.156 10 false 3D 4.917,5.313 5.146,5.469 0.229,0.156 10 false 3A 1.833,5.323 2.063,5.479 0.229,0.156 10 false 3B 4.229,6.906 4.448,7.063 0.219,0.156 10 false D6 3.063,6.906 3.344,7.063 0.281,0.156 10 false A73 3.698,6.906 3.917,7.063 0.219,0.156 10 false D5 5.896,7.51 6.125,7.667 0.229,0.156 10 false D6 3.594,7.51 3.823,7.667 0.229,0.156 10 false D5 1.125,7.521 1.406,7.677 0.281,0.156 10 false A73

Text in Illustration
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Network Gateway ECU)

a.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
MB-1 (BECU) - Body ground Input None - Body ground Battery power supply Always 11 to 14 V -
MB-8 (IG) - Body ground Input None - Body ground Engine switch power supply Engine switch on (IG) 11 to 14 V IG SW
Engine switch off Below 1 V
MB-9 (ACC) - Body ground Input None - Body ground ACC power supply Engine switch on (ACC) 11 to 14 V ACC SW
Engine switch off Below 1 V
MB-11 (GND) - Body ground Input None - Body ground Ground Always Below 1 Ω -
MB-32 (BMPX) - Body ground Input None - Body ground Battery power supply Always 11 to 14 V -
D6-1 (GND) - Body ground - B - Body ground Ground Always Below 1 Ω -
A73-4 (GND) - Body ground - B-Y - Body ground Ground Always Below 1 Ω -

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
3A-28 - Body ground Input V - Body ground Driver side door courtesy light switch input Driver side door open Below 1 V D Door Courtesy SW
Driver side door closed 11 to 14 V
3B-13 - Body ground Input GR - Body ground Passenger side door courtesy light switch input Passenger side door open Below 1 V P Door Courtesy SW
Passenger side door closed 11 to 14 V
3D-26 - Body ground Input SB - Body ground Luggage compartment door courtesy light switch input Luggage compartment door open Below 1 V Luggage Courtesy SW
Engine switch off, all doors closed and luggage compartment door closed 11 to 14 V
D5-22 (ACC) - Body ground Input W - Body ground ACC power supply Engine switch on (ACC) 11 to 14 V ACC SW
Engine switch off Below 1 V
D5-11 (L2) - Body ground*1 Input BE - Body ground Driver side door lock and unlock switch input Driver side door key cylinder in lock position Below 1 V -
Engine switch off, all doors closed and driver side door key cylinder in neutral position Pulse generation (See waveform 1 or 2)
D5-12 (UL2) - Body ground*1 Input R - Body ground Driver side door lock and unlock switch input Driver side door key cylinder in unlock position Below 1 V -
Engine switch off, all doors closed and driver side door key cylinder in neutral position Pulse generation (See waveform 1 or 2)
3B-2 - Body ground Output V - Body ground Door lock motor lock drive output (for driver side) Driver side door control switch not pushed and driver side door key cylinder in neutral position*1 Below 1 V -
Lock side of driver side door control switch pushed or driver side door key cylinder in lock position*1 11 to 14 V
3B-3 - Body ground Output L - Body ground Door lock motor lock drive output (for passenger side) Driver side door control switch not pushed and driver side door key cylinder in neutral position*1 Below 1 V -
Lock side of driver side door control switch pushed or driver side door key cylinder in lock position*1 11 to 14 V
3B-6 - Body ground Output G - Body ground Door lock motor lock drive output (for luggage compartment door) Luggage open switch of electrical key transmitter sub-assembly not pressed Below 1 V Trunk and Back- Door Open
Luggage open switch of electrical key transmitter sub-assembly pressed 11 to 14 V
3B-1 - Body ground Output R-G - Body ground Door lock motor unlock drive output (for driver side) Driver side door control switch not pushed and driver side door key cylinder in neutral position* Below 1 V -
Unlock side of driver side door control switch pushed or driver side door key cylinder in unlock position* 11 to 14 V
3B-4 - Body ground Output L-W - Body ground Door lock motor unlock drive output (for passenger side) Driver side door control switch not pushed and driver side door key cylinder in neutral position* Below 1 V -
Unlock side of driver side door control switch pushed or driver side door key cylinder in unlock position* 11 to 14 V
D6-11 (LSFD) - Body ground Input W - Body ground Driver side door unlock detection switch input Driver side door unlocked Below 1 V D-Door Lock Pos SW
Engine switch off, all doors closed and driver side door locked Pulse generation (See waveform 1 or 2)
D6-12 (LSFP) - Body ground Input SB - Body ground Passenger side door unlock detection switch input Passenger side door unlocked Below 1 V P-Door Lock Pos SW
Engine switch off, all doors closed and passenger side door locked Pulse generation (See waveform 1 or 2)

*: w/ Key-linked Switch



e.

Inspect using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B199631E02
0.155,0.953 0.489,1.113 0.335,0.161 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection D5-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver side door key cylinder in neutral position

Measurement Condition
Item Content
Tester Connection D5-12 (UL2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver side door key cylinder in neutral position

Measurement Condition
Item Content
Tester Connection D6-11 (LSFD) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver side door locked

Measurement Condition
Item Content
Tester Connection D6-12 (LSFP) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and passenger side door locked


ii.
B199632E04
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection D5-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver side door key cylinder in neutral position

Measurement Condition
Item Content
Tester Connection D5-12 (UL2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver side door key cylinder in neutral position

Measurement Condition
Item Content
Tester Connection D6-11 (LSFD) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and driver side door locked

Measurement Condition
Item Content
Tester Connection D6-12 (LSFP) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Engine switch off, all doors closed and passenger side door locked