Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297681 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly is in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

HINT:

When the battery cable is disconnected and reconnected, the power source mode returns to the mode it was in before the battery cable was disconnected.


WIRING DIAGRAM

B312725E04
3.49,1.01 3.594,1.156 0.104,0.146 10 false 6 2.573,4.104 2.917,4.271 0.344,0.167 10 false GND 3.01,1.229 3.333,1.375 0.323,0.146 10 false IG1D 3.438,1.229 3.667,1.375 0.229,0.146 10 false D41 4,1.031 4.167,1.177 0.167,0.146 10 false 15 3.99,1.229 4.156,1.375 0.167,0.146 10 false 3A 4.031,0.583 4.125,0.74 0.094,0.156 10 false 1 3.99,0.813 4.167,0.958 0.177,0.146 10 false 3E 5.708,0.979 6.292,1.135 0.583,0.156 10 false ECU IG1 6.458,4.083 6.635,4.229 0.177,0.146 10 false 12 6.448,4.281 6.656,4.458 0.208,0.177 10 false 3A 6.49,3.625 6.583,3.771 0.094,0.146 10 false 3 6.469,3.875 6.635,4.021 0.167,0.146 10 false 3A 6.469,2.667 6.635,2.813 0.167,0.146 10 false 32 6.458,2.865 6.646,3.042 0.188,0.177 10 false 3A 6.479,1.635 6.646,1.781 0.167,0.146 10 false 34 6.469,1.844 6.635,1.99 0.167,0.146 10 false 3C 6.479,0.625 6.646,0.771 0.167,0.146 10 false 35 6.469,0.813 6.656,0.979 0.188,0.167 10 false 3C 4.844,4.5 5.438,4.646 0.594,0.146 10 false IG1 NO.4 4.854,3.5 5.448,3.646 0.594,0.146 10 false IG1 NO.3 4.854,2.49 5.448,2.635 0.594,0.146 10 false IG1 NO.2 4.854,1.458 5.448,1.604 0.594,0.146 10 false IG1 NO.1 5.927,2.01 6.167,2.156 0.24,0.146 10 false DRL 5.792,4 6.323,4.323 0.531,0.323 10 false SEAT HTR RH 5.802,3.021 6.375,3.177 0.573,0.156 10 false HEATER 2.281,3.885 2.458,4.031 0.177,0.146 10 false 11 2.229,4.104 2.51,4.271 0.281,0.167 10 false D48 2.323,2.563 2.427,2.708 0.104,0.146 10 false 9 2.313,1.01 2.417,1.156 0.104,0.146 10 false 2 2.24,2.781 2.51,2.938 0.271,0.156 10 false D48 2.24,1.219 2.521,1.375 0.281,0.156 10 false D48 2.583,1.219 2.76,1.365 0.177,0.146 10 false +B 1.406,1.365 2.083,1.531 0.677,0.167 10 false AM2 NO.2 0.177,1.219 1.219,1.417 1.042,0.198 10 false from MAIN Fuse 4.052,4.875 6.708,5.094 2.656,0.219 10 false Instrument Panel Junction Block Assembly 2.125,4.906 3.656,5.271 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly) 2.594,2.771 2.917,2.917 0.323,0.146 10 false IG2D 1.115,3.01 1.365,3.156 0.25,0.146 10 false IG2 0.813,2.25 0.906,2.406 0.094,0.156 10 false 3 1.563,2.281 1.667,2.427 0.104,0.146 10 false 5 0.802,2.677 0.896,2.844 0.094,0.167 10 false 1 1.563,2.677 1.667,2.823 0.104,0.146 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 RELAY)
a.

Disconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Remove the IG2 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D48-9 (IG2D) - IG2 relay terminal 2 Always Below 1 Ω
IG2 relay terminal 1 - Body ground Always Below 1 Ω




OK

2.INSPECT IG2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT IG2 RELAY

OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE IG2 RELAY

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Connection Specified Condition
D41-6 (IG1D) - 3A-15 Always Below 1 Ω
3A-12 - Body ground Always Below 1 Ω




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY ((IG1 NO. 1, IG1 NO. 2, IG1 NO. 3, IG1 NO. 4 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY ((IG1 NO. 1, IG1 NO. 2, IG1 NO. 3, IG1 NO. 4 RELAY)
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U190258E02
0.104,0.063 0.292,0.219 0.188,0.156 10 false *a 1.26,0.375 1.479,0.531 0.219,0.156 10 false 3C 6.146,0.344 6.354,0.5 0.208,0.156 10 false 3E 3.99,0.354 4.198,0.51 0.208,0.156 10 false 3A

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Connection Specified Condition
3E-1 - 3C-35 Battery voltage not applied to terminals 3A- 15 and 3A-12 10 kΩ or higher
Battery voltage applied to terminals 3A- 15 and 3A-12 Below 1 Ω
3E-1 - 3C-34 Battery voltage not applied to terminals 3A- 15 and 3A-12 10 kΩ or higher
Battery voltage applied to terminals 3A- 15 and 3A-12 Below 1 Ω
3E-1 - 3A-32 Battery voltage not applied to terminals 3A- 15 and 3A-12 10 kΩ or higher
Battery voltage applied to terminals 3A- 15 and 3A-12 Below 1 Ω
3E-1 - 3A-3 Battery voltage not applied to terminals 3A- 15 and 3A-12 10 kΩ or higher
Battery voltage applied to terminals 3A- 15 and 3A-12 Below 1 Ω




OK

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.


b.

Measure the voltage according to the value(s) in the table below.

U190190E01
0.302,0.29 0.488,0.451 0.186,0.161 10 *a 4.805,0.934 5.100,1.090 0.295,0.156 10 D41 2.187,0.932 2.482,1.088 0.295,0.156 10 D48 4.388,1.629 4.13,2.287 false 1.978,1.736 1.762,2.287 false 3.927,2.312 4.290,2.468 0.363,0.156 10 IG1D 1.531,2.313 1.893,2.469 0.363,0.156 10 IG2D

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

Standard Voltage :
Tester Connection Switch Condition Specified Condition
D41-6 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) Below 1 V → 9 V or higher
D48-9 (IG2D) - Body ground Engine switch on (ACC) → Engine switch on (IG) Below 1 V → 9 V or higher




OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)