Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297681 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (ACC)  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the vehicle and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Use this troubleshooting procedure when the power source mode does not change to on (ACC) but does change to on (IG).

HINT:

When the battery cable is disconnected and reconnected, the power source mode returns to the mode it was in before the battery cable was disconnected.


WIRING DIAGRAM

B312726E04
2.573,2.438 2.896,2.615 0.323,0.177 10 false GND 4,0.5 4.167,0.656 0.167,0.156 10 false 1 3.979,0.698 4.198,0.844 0.219,0.146 10 false 3E 2.302,2.271 2.5,2.5 0.198,0.229 10 false 11 2.25,2.458 2.531,2.604 0.281,0.146 10 false D48 2.323,0.938 2.5,1.083 0.177,0.146 10 false 2 2.229,1.115 2.49,1.271 0.26,0.156 10 false D48 2.594,1.104 2.833,1.281 0.24,0.177 10 false +B 1.458,1.271 2.167,1.448 0.708,0.177 10 false AM2 NO.2 0.156,1.125 1.25,1.302 1.094,0.177 10 false from MAIN Fuse 3.969,2.927 6.635,3.125 2.667,0.198 10 false Instrument Panel Junction Block Assembly 2.219,2.99 3.75,3.365 1.531,0.375 10 false Certification ECU (Smart Key ECU Assembly) 6.521,2.208 6.75,2.396 0.229,0.188 10 false 12 6.521,2.365 6.719,2.542 0.198,0.177 10 false 3A 6.51,1.688 6.74,1.844 0.229,0.156 10 false 10 6.521,1.865 6.74,2.01 0.219,0.146 10 false 3A 6.521,0.531 6.75,0.688 0.229,0.156 10 false 28 6.521,0.708 6.74,0.927 0.219,0.219 10 false 3B 5.052,2.594 5.469,2.75 0.417,0.156 10 false ACC2 5.073,1.365 5.469,1.51 0.396,0.146 10 false ACC1 5.875,2 6.396,2.333 0.521,0.333 10 false P/POINT NO.1 5.854,0.854 6.479,1.031 0.625,0.177 10 false ECU ACC 3.521,0.927 3.667,1.083 0.146,0.156 10 false 4 2.948,1.115 3.344,1.292 0.396,0.177 10 false ACCD 3.438,1.104 3.708,1.281 0.271,0.177 10 false D41 3.99,0.927 4.177,1.094 0.188,0.167 10 false 20 3.979,1.115 4.177,1.292 0.198,0.177 10 false 3A

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not reoccur.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU)

OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)