Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297681 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit between the ACC output terminal of the certification ECU (smart key ECU assembly) and the ACC relay is detected.

HINT:

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2274 Malfunction in the ACC relay activation circuit in the certification ECU (smart key ECU assembly) or the external circuit (1-trip detection logic*1).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

AM2 No. 2 fuse

·

Instrument panel junction block assembly (ACC relay)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.
HINT:

To turn the engine switch on (ACC), carry the key and press the engine switch with the shift lever in P or N*2 and the brake pedal*2 or clutch pedal*3 released.



*1: Only output while a malfunction is present and the engine switch is on (IG)

*2: for Automatic Transmission

*3: for Manual Transmission


Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction when the relay is stuck on, the ACC relay does not turn off even though all the power is off.

·

If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).


HINT:

The engine switch can be turned on (IG) and the engine can be started.


-

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2274
Power Source Control
·

ACC Relay Monitor


Engine
·

Ignition Status


-

WIRING DIAGRAM

B312726E03
2.583,2.458 2.896,2.604 0.313,0.146 10 false GND 4.042,0.51 4.135,0.667 0.094,0.156 10 false 1 3.99,0.698 4.208,0.844 0.219,0.146 10 false 3E 2.271,2.281 2.448,2.427 0.177,0.146 10 false 11 2.229,2.448 2.51,2.604 0.281,0.156 10 false D48 2.313,0.927 2.417,1.073 0.104,0.146 10 false 2 2.229,1.125 2.521,1.281 0.292,0.156 10 false D48 2.573,1.115 2.802,1.292 0.229,0.177 10 false +B 1.448,1.292 2.146,1.469 0.698,0.177 10 false AM2 NO.2 0.094,1.146 1.25,1.323 1.156,0.177 10 false from MAIN Fuse 4.021,2.927 6.708,3.146 2.688,0.219 10 false Instrument Panel Junction Block Assembly 2.156,3.01 3.688,3.365 1.531,0.354 10 false Certification ECU (Smart Key ECU Assembly) 6.521,2.208 6.688,2.354 0.167,0.146 10 false 12 6.51,2.385 6.729,2.563 0.219,0.177 10 false 3A 6.51,1.677 6.74,1.844 0.229,0.167 10 false 10 6.51,1.844 6.729,2.01 0.219,0.167 10 false 3A 6.51,0.521 6.74,0.677 0.229,0.156 10 false 28 6.51,0.698 6.729,0.865 0.219,0.167 10 false 3B 5.052,2.604 5.469,2.771 0.417,0.167 10 false ACC2 5.063,1.344 5.469,1.51 0.406,0.167 10 false ACC1 5.875,2 6.417,2.333 0.542,0.333 10 false P/POINT NO.1 5.854,0.865 6.479,1.042 0.625,0.177 10 false ECU ACC 3.5,0.938 3.646,1.083 0.146,0.146 10 false 4 2.948,1.094 3.323,1.271 0.375,0.177 10 false ACCD 3.427,1.115 3.698,1.26 0.271,0.146 10 false D41 4,0.938 4.198,1.083 0.198,0.146 10 false 20 3.99,1.115 4.198,1.292 0.208,0.177 10 false 3A

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU)
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D41-4 (ACCD) - 3A-20 Always Below 1 Ω
3A-12 - Body ground Always Below 1 Ω
D41-4 (ACCD) - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC1, ACC2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC1, ACC2 RELAY)
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U190242E02
0.094,0.052 0.281,0.208 0.188,0.156 10 false *a 1.146,0.25 1.344,0.406 0.198,0.156 10 false 3B 6.125,0.25 6.323,0.406 0.198,0.156 10 false 3E 3.917,0.25 4.125,0.406 0.208,0.156 10 false 3A

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3E-1 - 3B-28 When battery voltage absent 10 kΩ or higher
When battery voltage is applied to terminals 3A-20 and 3A-12 Below 1 Ω
3E-1 - 3A-10 When battery voltage absent 10 kΩ or higher
When battery voltage is applied to terminals 3A-20 and 3A-12 Below 1 Ω




OK

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


b.

Install the instrument panel junction block assembly.


c.

Reconnect the D41 certification ECU (smart key ECU assembly) connector.


U190195E01
0.154,0.105 0.340,0.266 0.186,0.161 10 *a 1.47,0.318 1.765,0.474 0.295,0.156 10 D41 1.161,1.086 0.878,1.811 false 0.568,1.844 0.994,1.991 0.426,0.147 10 ACCD

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D41-4 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) Below 1 V → 8.5 V or higher


Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)