This DTC is stored when the steering lock position signal sent by the steering lock actuator assembly (steering lock ECU) via direct line and the steering lock position signal sent via LIN communication do not match.
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.
| DTC No. | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B2285 | The steering lock position signal sent by the steering lock ECU via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match. | ·
AM2 No. 2 fuse ·
Steering lock actuator assembly (steering lock ECU) ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait another 40 seconds or more with the engine switch off (steering locked), and then turn the engine switch on (ACC) (steering unlocked) and wait 40 seconds or more. |
*: Only output while a malfunction is present and the engine switch is on (IG)
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The engine cannot be started. | An engine start command is not output. |
| DTC No. | Data List Item | Active Test Item |
|---|---|---|
| B2285 | Power Source Control
·
Steering Unlock Switch Entry & Start
·
Power Supply Short ·
Lock Bar Stuck Error ·
Motor Driver Short |
- |
When using the GTS with the engine switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).
Before replacing the certification ECU (smart key ECU assembly) or steering lock actuator assembly (steering lock ECU), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
If the entry key indicator in the combination meter assembly illuminates in green, the steering lock bar may be stuck.
Clear the DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).
LIN communication system DTC B2785 is not output simultaneously.
If the steering wheel cannot be locked or unlocked, the engine switch cannot be turned on (IG) and the engine cannot be started.
If LIN communication is not available, the steering wheel cannot be locked or unlocked.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock actuator assembly/OFF or ON | OFF: Steering locked
ON: Steering unlocked |
·
When the shift lever is in P* and the engine switch is off, if any door is opened or closed, the steering is locked. ·
When the electrical key transmitter sub-assembly is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks. ·
The engine cannot be started when the steering unlock signal is off. |
*: for Automatic Transmission
| Result | Proceed to |
|---|---|
| Data List item does not change | A |
| Data List item changes (for LHD) | B |
A
B
OK
NG
OK
NG
Reconnect the D59 steering lock actuator assembly (steering lock ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) tester probe → D59-4 (SLP)
Negative (-) tester probe → Body ground |
Steering locked* | 10 kΩ or higher |
| Positive (+) tester probe → D59-4 (SLP)
Negative (-) tester probe → Body ground |
Steering unlocked* | Below 1 Ω |
*: If any of the doors are opened then closed with the shift lever in P* and the engine switch off, the steering wheel will be locked. If the engine switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.
DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator assembly) to the certification ECU (smart key ECU assembly) individually.
*: for Automatic Transmission
| *a | Component with harness connected
(Steering Lock Actuator Assembly (Steering Lock ECU)) |
OK
NG
Disconnect the D41 certification ECU (smart key ECU assembly) connector.
Disconnect the D59 steering lock actuator assembly (steering lock ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-26 (SLP) - D59-4 (SLP1) | Always | Below 1 Ω |
| D41-26 (SLP) - Body ground | Always | 10 kΩ or higher |
OK
NG