Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297682 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B1572  Immobiliser System Communication Malfunction  


DESCRIPTION

The ECM stores this code if a communication problem is detected between the ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 and the ECM.

*1: w/ ID Code Box

*2: w/o ID Code Box


DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B1572 When there is a problem in communication between the ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 and the ECM (1 trip detection logic*3):
·

ID code box (immobiliser code ECU)*1

·

Certification ECU (smart key ECU assembly)*2

·

ECM

·

Harness or connector


Engine switch on (IG)

*1: w/ ID Code Box

*2: w/o ID Code Box

*3: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC Code Data List and Active Test
B1572
Entry&Start

Immobiliser



WIRING DIAGRAM

B317010E02
0.927,2.813 2.75,3.177 1.823,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.938,2.635 1.229,2.792 0.292,0.156 10 false D48 6.115,2.51 6.479,2.677 0.365,0.167 10 false ECM 6.115,2.333 6.406,2.49 0.292,0.156 10 false A35 2.271,1.552 2.479,1.719 0.208,0.167 10 false 13 2.281,2.281 2.49,2.448 0.208,0.167 10 false 11 1.885,2.417 2.24,2.583 0.354,0.167 10 false GND 1.833,1.667 2.24,1.833 0.406,0.167 10 false EGIO 5.906,1.677 6.271,1.844 0.365,0.167 10 false IMO 5.656,1.563 5.854,1.729 0.198,0.167 10 false 25 0.708,1.188 3.135,1.354 2.427,0.167 10 false ID Code Box (Immobiliser Code ECU)*1 0.708,1.021 1,1.177 0.292,0.156 10 false A30 1.521,3.354 2.833,3.542 1.313,0.188 10 false *2: w/o ID Code Box 0.167,3.365 1.396,3.552 1.229,0.188 10 false *1: w/ ID Code Box 2.271,0.594 2.385,0.75 0.115,0.156 10 false 5 2.271,0.156 2.385,0.313 0.115,0.156 10 false 4 1.875,0.729 2.229,0.896 0.354,0.167 10 false GND 1.854,0.281 2.219,0.448 0.365,0.167 10 false IMO1 4.135,1.25 4.344,1.427 0.208,0.177 10 false *1 3.635,1.542 3.844,1.719 0.208,0.177 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU or ID code box (immobiliser code ECU)*, refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



*: w/ ID Code Box


PROCEDURE

1.READ VALUE USING GTS (IMMOBILISER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system status when power source mode on (IG) / Unset or Set Set: Engine immobiliser set (engine start prohibited) (engine switch off)
Unset: Engine immobiliser unset (engine start permitted) [engine switch on (ACC) or on (IG)]
If "Set" is displayed, the engine start function is prohibited.


OK:

On the GTS screen, the display changes between Set and Unset as shown in the table above.



OK

2.CHECK VEHICLE CONDITION

NG

2.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result Proceed to
w/ ID Code Box A
w/o ID Code Box B


A

3.CHECK HARNESS AND CONNECTOR

B

6.CHECK HARNESS AND CONNECTOR
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect the A30 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A35 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
A30-4 (IMO1) - A35-25 (IMO) Always Below 1 Ω
A30-4 (IMO1) - Body ground Always 10 kΩ or higher




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM
a.

Temporarily replace the ECM with a new one (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>ECM>REMOVAL).



NEXT

5.REGISTER ECU COMMUNICATION ID
5.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (Refer to Service Bulletin).


b.

Check that the engine can be started.


OK:

The engine can be started.



OK

END (ECM WAS DEFECTIVE)

NG

ID CODE BOX (IMMOBILIZER CODE ECU)

6.CHECK HARNESS AND CONNECTOR
a.

Disconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A35 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
D48-13 (EGIO) - A35-25 (IMO1) Always Below 1 Ω
D48-13 (EGIO) - Body ground Always 10 kΩ or higher




OK

7.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ECM
a.

Temporarily replace the ECM with a new one (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>ECM>REMOVAL).



NEXT

8.REGISTER ECU COMMUNICATION ID
8.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (Refer to Service Bulletin).


b.

Check that the engine can be started.


OK:

The engine can be started.



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)