Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297681 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the vehicle and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P or N*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch.

*1: for Automatic Transmission

*2: for Manual Transmission


HINT:
·

The engine can be started up with the shift lever in N only when the steering lock is unlocked*.

·

If the engine switch is pressed when the power source mode is on (IG) and the shift lever is in a position other than P, the power source mode changes to on (ACC). If the shift lever is then moved to P and the engine switch is pressed while stepping on the brake pedal, the power source mode changes to off*.

·

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.



*: for Automatic Transmission


Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Engine does not start
Power Source Control
·

Shift P Signal

·

Steering Unlock Switch

·

Stop Light Switch1

·

Neutral SW/ Clutch SW

·

Latch Circuit

·

IG1 Relay Monitor(Outside)

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Outside)

·

IG2 Relay Monitor(Inside)

·

Starter Request Signal

·

Power Supply Condition


Entry & Start
·

Immobiliser

·

Engine Start Request

·

S Code Check

·

L Code Check


Engine
·

Shift SW Status (P Range)

·

Shift SW Status (N Range)

·

Ignition Status


-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly), steering lock actuator assembly (steering lock ECU), ID code box (immobiliser code ECU), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

If the steering lock actuator assembly (steering lock ECU) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

·

After completing repairs, confirm that the problem does not reoccur.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal to illuminate the stop lights increases.*

*: for Automatic Transmission



PROCEDURE

1.CHECK BATTERY
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:
·

It may be possible to tell whether the vehicle battery is discharged by operating the horn.

·

If the battery voltage is less than 11 V, charge or replace it.





NEXT

2.CHECK DTC (ALL)
2.CHECK DTC (ALL)
a.

Using the GTS, confirm the output of DTCs for all systems.

OK:

No DTCs are output




OK

3.CHECK WAVE ENVIRONMENT

NG

3.CHECK WAVE ENVIRONMENT
a.

If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

HINT:

Whether or not the problem is due to wave interference can be checked by holding the electrical key transmitter assembly near the door control receiver (RF band).




NEXT

4.CHECK ENGINE SWITCH CONDITION
4.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter assembly.


b.

Move the shift lever to P*.

*: for Automatic Transmission



c.

With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.

*1: for Automatic Transmission

*2: for Manual Transmission


Result
Result Proceed to
Power source mode changes as follows (normal): off → on (ACC) → on (IG) → off A
Power source mode does not change to on (IG) or on (ACC) B
Power source mode does not change to on (IG) but does change to on (ACC) C
Power source mode does not change to on (ACC) but does change to on (IG) D



A

5.CHECK CRANKING FUNCTION

B

C

D

5.CHECK CRANKING FUNCTION
a.

Get into the vehicle while carrying the electrical key transmitter assembly.


b.

Move the shift lever to P*.

*: for Automatic Transmission



c.

Depress the brake pedal*1 or clutch pedal*2.

*1: for Automatic Transmission

*2: for Manual Transmission



d.

Confirm that the entry key indicator in the combination meter assembly illuminates in green, and then press the engine switch and check that the engine cranks.

OK:

Engine cranks


Result
Result Proceed to
NG A
OK B



A

6.READ VALUE USING GTS (IMMOBILISER)

B

GO TO SFI SYSTEM (PROBLEM SYMPTOMS TABLE)

6.READ VALUE USING GTS (IMMOBILISER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser State of immobiliser system determined by certification ECU (smart key ECU assembly) / Set or Unset Set: Engine immobiliser set (engine start prohibited) (engine switch off)
Unset: Engine immobiliser unset (engine start permitted) (engine switch on (ACC) or on (IG))
·

When the immobiliser cannot be unset, this item can be used to determine whether the certification ECU (smart key ECU assembly) is part of the problem.

·

The engine cannot be started when this item displays "Set"



OK:

The Data List item changes to "Unset" when the engine switch is turned on (ACC) or on (IG).


Result
Result Proceed to
OK A
NG (w/ ID Code Box) B
NG (w/o ID Code Box) C



A

7.CHECK COMBINATION METER ASSEMBLY (ENTRY KEY INDICATOR LIGHT)

B

10.READ VALUE USING GTS (S CODE CHECK)

C

11.CHECK STEERING LOCK
7.CHECK COMBINATION METER ASSEMBLY (ENTRY KEY INDICATOR LIGHT)
a.

Get into the vehicle while carrying the electrical key transmitter assembly, move the shift lever to P*1, depressing the brake pedal*1 or clutch pedal*2 and check that the entry key indicator light in the combination meter assembly changes.

*1: for Automatic Transmission

*2: for Manual Transmission


OK:

The entry key indicator light in green.


HINT:

If the entry key indicator light in the combination meter assembly illuminates green when the procedure above is performed, the P, N and brake signals*1 or clutch signal*2 can be considered to be normal.


*1: for Automatic Transmission

*2: for Manual Transmission


Result
Result Proceed to
OK A
NG (for Automatic Transmission) B
NG (for Manual Transaxle) C



A

8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

B

14.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT SW STATUS P OR N)

C

20.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Starter Request Signal Condition of engine start command signal / OFF or ON OFF: Engine switch released after approximately 1 second elapses
ON: Engine switch pressed and held while carrying electrical key transmitter assembly with shift lever in P*1 and brake pedal*1 or clutch pedal*2 depressed
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.



*1: for Automatic Transmission

*2: for Manual Transmission


OK:

The display changes in response to the operation of the engine switch.


NOTICE:

Make sure that the entry key indicator in the combination meter assembly illuminates in green before pressing the engine switch.




OK

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.

Disconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A33 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D48-7 (STSW) - A33-17 (STSW) Always Below 1 Ω
D48-7 (STSW) - Body ground Always 10 kΩ or higher




OK

GO TO SFI SYSTEM (PROBLEM SYMPTOMS TABLE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (S CODE CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

S code has not been registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK (S code certification result normal) appears on the screen.




OK

11.CHECK STEERING LOCK

NG

23.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
11.CHECK STEERING LOCK
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.




OK

12.READ VALUE USING GTS (IMMOBILISER)

NG

25.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
12.READ VALUE USING GTS (IMMOBILISER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser State of immobiliser system determined by certification ECU (smart key ECU assembly) / Set or Unset Unset: Engine immobiliser unset (engine switch on [ACC] or on [IG])
Set: Engine immobiliser set (engine switch off)
·

When the immobiliser cannot be unset, this item can be used to determine whether the certification ECU (smart key ECU assembly) is part of the problem.

·

The engine cannot be started when this item displays "Set"



OK:

The Data List item changes to "Unset" when the engine switch is turned on (ACC) or on (IG).


Result
Result Proceed to
OK A
NG (w/ ID Code Box) B
NG (w/o ID Code Box) C



A

13.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

B

29.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Starter Request Signal Condition of engine start command signal / OFF or ON OFF: Engine switch released after approximately 1 second elapses
ON: Engine switch pressed and held while carrying electrical key transmitter assembly with shift lever in P*1 and brake pedal*1 or clutch pedal*2 depressed
·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.



*1: for Automatic Transmission

*2: for Manual Transmission


OK:

The display changes in response to the operation of the engine switch.


NOTICE:

Make sure that the entry key indicator in the combination meter assembly illuminates in green before pressing the engine switch.




OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT SW STATUS P OR N)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral SW / Clutch SW Shift position (P, N) / OFF or ON OFF: Shift lever not in P or N or released
ON: Shift lever in P or N depressed
·

Use this item to help determine if the park/neutral position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".



Enter the following menus: Powertrain / Engine / Data List.

Engine
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Condition of park/neutral position switch / OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
When malfunctioning, the engine will not crank.
Shift SW Status (N Range) Condition of park/neutral position switch / OFF or ON OFF: Shift lever not in N
ON: Shift lever in N
When malfunctioning, the engine will not crank.

OK:

The items in the Data List change according to the shift position.




OK

15.READ VALUE USING GTS (STOP LIGHT SWITCH1)

NG

16.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
15.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal / OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.



OK:

The item in the Data List changes when the brake pedal is depressed and released.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

18.INSPECT STOP LIGHT SWITCH ASSEMBLY
16.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Remove the park/neutral position switch assembly (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL).


b.

Inspect the park/neutral position switch assembly (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L2 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D48-5 (N-SW) - L2-4 Always Below 1 Ω
L2-5 - Body ground Always Below 1 Ω
D48-5 (N-SW) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

19.CHECK HARNESS AND CONNECTOR (NOISE FILTER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

19.CHECK HARNESS AND CONNECTOR (NOISE FILTER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral SW / Clutch SW State of clutch pedal / OFF or ON OFF: Clutch pedal released
ON: Clutch pedal depressed
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".



OK:

ON (clutch pedal depressed) and OFF (clutch pedal released) appear on the screen according to the condition of the clutch pedal.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

21.INSPECT CLUTCH START SWITCH ASSEMBLY
21.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Remove the clutch start switch assembly.



b.

Inspect the clutch start switch assembly.



Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

B

REPLACE CLUTCH START SWITCH ASSEMBLY

C

REPLACE CLUTCH START SWITCH ASSEMBLY

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A20 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D48-10 (CLUT) - A20-2 Always Below 1 Ω
D48-10 (CLUT) - Body ground Always 10 kΩ or higher



d.

Reconnect the A20 clutch start switch assembly connector.


e.
U160592E01
0.078,0.027 0.263,0.189 0.186,0.161 10 *a 0.537,1.329 0.833,1.485 0.295,0.156 10 F65 1.991,1.473 2.209,1.87 false 2.061,1.895 2.460,2.051 0.399,0.156 10 STAR

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D48-10 (CLUT) - Body ground Clutch pedal released → Clutch pedal depressed 1 V or less → 9 V or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

NOTICE:

When the certification ECU (smart key ECU assembly) is replaced, it is also necessary to replace all registered electrical key transmitter sub-assemblies.



b.

Perform the registration procedures (Refer to Service Bulletin).


c.

Use the Data List to check if S code certification is functioning properly again.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

S code has not been registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK (S code certification result normal) appears on the screen.




OK

END

NG

24.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
24.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.


b.

Perform the registration procedures (Refer to Service Bulletin).


c.

Use the Data List to check if S code certification is functioning properly again.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

S code has not been registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK (S code certification result normal) appears on the screen.




NEXT

END

25.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly / OFF or ON OFF: Steering locked
ON: Steering unlocked
·

When the shift lever is in P and the engine switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter assembly is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.



OK:

The item in the Data List indicates "ON" (the steering is unlocked).




OK

GO TO STEERING LOCK SYSTEM (UNABLE TO UNLOCK STEERING WHEEL)

NG

26.READ VALUE USING GTS (L CODE CHECK)
26.READ VALUE USING GTS (L CODE CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock actuator assembly (steering lock ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

L code has not been registered for the ID code box (immobiliser code ECU) or steering lock actuator assembly (steering lock ECU).

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

The Data List item changes to "OK" when the electrical key transmitter assembly is inside the vehicle.


HINT:

Reasons for verification failure:

·

The steering lock ECU, ID code box (immobiliser code ECU)* is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.


*: w/ ID Code Box





OK

27.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

NG

28.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
27.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
a.

Replace the steering lock actuator assembly (steering lock ECU) with a new one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL).


b.

Perform the registration procedures (Refer to Service Bulletin).


c.

Turn the engine switch on (IG).


d.

Operate the steering wheel and check the steering condition.



NEXT

END

28.REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)
a.

Replace the steering lock actuator assembly (steering lock ECU) with a new one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL).


b.

Perform the registration procedures (Refer to Service Bulletin).


c.

Use the Data List to check if L code certification is functioning properly again.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock actuator assembly (steering lock ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

L code has not been registered for the ID code box (immobiliser code ECU) or steering lock actuator assembly (steering lock ECU).

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK (L code certification result normal) appears on the screen.


Result
Result Proceed to
OK A
NG (w/ ID Code Box) B
NG (w/o ID Code Box) C



A

END

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

29.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.


b.

Perform the registration procedures (Refer to Service Bulletin for registration).


c.

Use the Data List to check if S code certification is functioning properly again.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

S code has not been registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK (S code certification result normal) appears on the screen.




OK

END

NG

30.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
30.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.


b.

Perform the registration procedures (Refer to Service Bulletin).


c.

Use the Data List to check if S code certification is functioning properly again.

Entry & Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

S code has not been registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

OK (S code certification result normal) appears on the screen.




NEXT

END