CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)
| *1 | Instrument Panel Junction Block Assembly | *2 | Main Body ECU (Network Gateway ECU) |
Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-1 (BECU) - Body ground | None - Body ground | Battery power supply | Always | 11 to 14 V |
| MB-8 (IG) - Body ground | None - Body ground | Engine switch power supply | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| MB-9 (ACC) - Body ground | None - Body ground | ACC power supply | Engine switch on (ACC) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| MB-11 (GND) - Body ground | None - Body ground | Ground | Always | Below 1 Ω |
| MB-32 (BMPX) - Body ground | None - Body ground | Battery power supply | Always | 11 to 14 V |
| D6-1 (GND) - Body ground | B - Body ground | Ground | Always | Below 1 Ω |
| A73-4 (GND) - Body ground | B-Y - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).
Measure the voltage and waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3A-28 - Body ground | V - Body ground | Driver side door courtesy light switch input | Driver side door open | Below 1 V |
| Driver side door closed | 11 to 14 V | |||
| 3B-13 - Body ground | GR - Body ground | Passenger side door courtesy light switch input | Passenger side door open | Below 1 V |
| Passenger side door closed | 11 to 14 V | |||
| 3B-22 - Body ground | V - Body ground | Security indicator light signal | Security indicator light illuminated (illuminates only for 60 seconds in alarm sounding state (blinks when system in armed state)) | Below 4 V |
| 3D-26 - Body ground | SB - Body ground | Luggage compartment door courtesy light switch input | Luggage compartment door open | Below 1 V |
| Engine switch off, all doors closed and luggage compartment door closed | 11 to 14 V | |||
| 3D-31 - Body ground | BR - Body ground | Vehicle horn signal | Vehicle horns sounding (Theft deterrent system is in alarm sounding state) | Pulse generation |
| Vehicle horns not sounding (Theft deterrent system is in armed state) | 11 to 14 V | |||
| 3B-2 - Body ground | V - Body ground | Door lock motor lock drive output (for driver side) | Driver side door control switch not pushed | Below 1 V |
| Lock side of driver side door control switch pushed | 11 to 14 V | |||
| 3B-3 - Body ground | L - Body ground | Door lock motor lock drive output (for passenger side) | Driver side door control switch not pushed | Below 1 V |
| Lock side of driver side door control switch pushed | 11 to 14 V | |||
| 3B-1 - Body ground | R-G - Body ground | Door lock motor unlock drive output (for driver side) | Driver side door control switch not pushed | Below 1 V |
| Unlock side of driver side door control switch pushed | 11 to 14 V | |||
| 3B-4 - Body ground | L-W - Body ground | Door lock motor unlock drive output (for passenger side) | Driver side door control switch not pushed | Below 1 V |
| Unlock side of driver side door control switch pushed | 11 to 14 V | |||
| D5-22 (ACC) - Body ground | W - Body ground | ACC power supply | Engine switch on (ACC) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| D6-11 (LSFD) - Body ground | W - Body ground | Driver side door unlock detection switch input | Driver side door unlocked | Below 1 V |
| Engine switch off, all doors closed and driver side door locked | Pulse generation (See waveform 1 or 2) | |||
| D6-12 (LSFP) - Body ground | SB - Body ground | Passenger side door unlock detection switch input | Passenger side door unlocked | Below 1 V |
| Engine switch off, all doors closed and passenger side door locked | Pulse generation (See waveform 1 or 2) |
Inspect using an oscilloscope.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Tester Connection | D6-11 (LSFD) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and driver side door locked |
| Item | Content |
|---|---|
| Tester Connection | D6-12 (LSFP) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and passenger side door locked |
Waveform 2 (Reference)
| Item | Content |
|---|---|
| Tester Connection | D6-11 (LSFD) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and driver side door locked |
| Item | Content |
|---|---|
| Tester Connection | D6-12 (LSFP) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Engine switch off, all doors closed and passenger side door locked |