Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297684 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B1410  Transponder Communication Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) stores this code if a communication problem is detected between the key and the main body ECU (network gateway ECU)


DTC Code DTC Detection Condition Trouble Area
B1410 When there is a problem in communication between the key and the main body ECU (network gateway ECU).
·

Key

·

Transponder key amplifier

·

Instrument panel junction block assembly

·

Main body ECU (network gateway ECU)

·

Harness or connector



WIRING DIAGRAM

B312642E03
2.75,3.292 4.354,3.656 1.604,0.365 10 false Main Body ECU (Network Gateway ECU) 0.083,2.667 1.74,2.854 1.656,0.188 10 false Transponder Key Amplifier 2.396,3.979 5.052,4.188 2.656,0.208 10 false Instrument Panel Junction Block Assembly 5.844,1.406 6.74,1.604 0.896,0.198 10 false to MAIN Fuse 0.083,2.5 0.344,2.667 0.26,0.167 10 false D54 1.865,1.927 1.979,2.094 0.115,0.167 10 false 7 1.865,1.438 2.021,1.583 0.156,0.146 10 false 4 1.875,1.031 2.031,1.198 0.156,0.167 10 false 5 1.875,0.583 1.99,0.75 0.115,0.167 10 false 1 1.385,1.448 1.813,1.625 0.427,0.177 10 false CODE 1.417,1.031 1.792,1.177 0.375,0.146 10 false TXCT 2.74,1.552 3.167,1.75 0.427,0.198 10 false CODE 2.75,1.125 3.177,1.333 0.427,0.208 10 false TXCT 2.75,2.021 3.177,2.167 0.427,0.146 10 false AGND 2.75,0.677 3.083,0.906 0.333,0.229 10 false VC5 1.385,1.917 1.813,2.073 0.427,0.156 10 false AGND 1.5,0.583 1.792,0.75 0.292,0.167 10 false VC5 2.438,1.823 2.604,1.99 0.167,0.167 10 false 16 2.438,0.938 2.667,1.094 0.229,0.156 10 false 15 2.479,0.479 2.667,0.688 0.188,0.208 10 false 8 2.479,1.365 2.594,1.531 0.115,0.167 10 false 5 2.406,2.01 2.74,2.156 0.333,0.146 10 false A73 2.406,1.552 2.74,1.698 0.333,0.146 10 false A73 2.417,1.115 2.75,1.271 0.333,0.156 10 false A73 2.417,0.667 2.75,0.854 0.333,0.188 10 false A73 3.771,2.75 4.021,2.917 0.25,0.167 10 false MB 3.771,2.25 4.052,2.438 0.281,0.188 10 false MB 3.781,1.771 4.042,2 0.26,0.229 10 false MB 5.281,2.229 5.49,2.406 0.208,0.177 10 false 3C 5.281,2.76 5.49,2.927 0.208,0.167 10 false 3B 5.292,1.771 5.5,1.938 0.208,0.167 10 false 3A 5.281,2.583 5.448,2.74 0.167,0.156 10 false 18 5.281,2.063 5.448,2.219 0.167,0.156 10 false 19 5.292,1.594 5.51,1.781 0.219,0.188 10 false 27 3.792,2.583 3.958,2.74 0.167,0.156 10 false 11 3.781,2.063 3.99,2.271 0.208,0.208 10 false 32 3.823,1.583 3.99,1.771 0.167,0.188 10 false 1 3.323,2.76 3.635,2.99 0.313,0.229 10 false GND 3.25,1.75 3.656,1.99 0.406,0.24 10 false BECU 3.26,2.229 3.677,2.417 0.417,0.188 10 false BMPX 6.365,1.906 6.677,2.083 0.313,0.177 10 false DCC 5.792,1.917 6.26,2.104 0.469,0.188 10 false ECU-B 5.792,2.406 6.281,2.583 0.49,0.177 10 false MPX-B 2.469,2.281 2.583,2.448 0.115,0.167 10 false 4 2.479,2.708 2.656,2.885 0.177,0.177 10 false 1 2.438,2.885 2.646,3.063 0.208,0.177 10 false D6 2.406,2.469 2.74,2.688 0.333,0.219 10 false A73 2.76,2.906 3.083,3.083 0.323,0.177 10 false GND 2.76,2.479 3.083,2.688 0.323,0.208 10 false GND 0.729,0.594 1.146,0.75 0.417,0.156 10 false ANT1 0.729,2.115 1.125,2.292 0.396,0.177 10 false ANT2 0.125,1.25 0.688,1.667 0.563,0.417 10 false Antenna coil

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (network gateway ECU) is replaced, refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK FOR DTC
a.

Using GTS, check that the DTC is stored with all the registered keys (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).


Result
Result Proceed to
DTC B1410 is stored with all the keys. A
DTC B1410 is not stored with some of the keys. B


A

2.CHECK HARNESS AND CONNECTOR (BATTERY, BODY GROUND)

B

REPLACE KEY THAT STORED DTC

2.CHECK HARNESS AND CONNECTOR (BATTERY, BODY GROUND)
a.

Disconnect the A73 and D6 main body ECU (network gateway ECU) connectors.


b.

Disconnect the 3A, 3B and 3C instrument panel junction block assembly connectors.


c.
U146922E05
0.063,0.063 0.25,0.219 0.188,0.156 10 false *a 1.625,0.24 1.833,0.396 0.208,0.156 10 false 3C 1.635,1.792 1.844,1.948 0.208,0.156 10 false 3A

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
3A-27 - Body ground Always 11 to 14 V
3C-19 - Body ground Always 11 to 14 V


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
3B-18 - Body ground Always Below 1 Ω
A73-4 (GND) - Body ground Always Below 1 Ω
D6-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


U190240E02
3.844,0.802 3.927,1 true 1.656,0.802 1.583,1.01 true 0.604,0.813 0.542,1.01 true 0.094,0.042 0.281,0.198 0.188,0.156 10 false *a 2.073,0.24 2.323,0.396 0.25,0.156 10 false MB 2.167,1.354 2.385,1.51 0.219,0.156 10 false 3C 5.552,1.365 5.771,1.521 0.219,0.156 10 false 3A 5.552,0.115 5.75,0.271 0.198,0.156 10 false 3B 3.771,1.031 4.229,1.208 0.458,0.177 10 false BMPX 1.417,1.031 1.76,1.188 0.344,0.156 10 false GND 0.344,1.031 0.76,1.188 0.417,0.156 10 false BECU

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
MB-1 (BECU) - 3A-27 Always Below 1 Ω
MB-32 (BMPX) - 3C-19 Always Below 1 Ω
MB-11 (GND) - 3B-18 Always Below 1 Ω



OK

4.INSPECT TRANSPONDER KEY AMPLIFIER (POWER SOURCE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.INSPECT TRANSPONDER KEY AMPLIFIER (POWER SOURCE)
a.

Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly.


b.

Install the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


c.

Reconnect the 3A, 3B and 3C instrument panel junction block assembly connectors.


d.

Disconnect the D54 transponder key amplifier connector.


e.
U146921E01
0.105,0.048 0.319,0.244 0.215,0.196 10 *a 1.607,0.271 1.902,0.427 0.295,0.156 10 D54 2.229,1.029 2.883,1.029 false 2.929,0.941 3.255,1.097 0.327,0.156 10 VC5

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
D54-1 (VC5) - Body ground Ignition switch ON 4.5 to 5.5 V


Result
Result Proceed to
NG A
OK B

Text in Illustration
*a Component with harness connected
(Transponder Key Amplifier)


A

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - INSTRUMENT PANEL JUNCTION BLOCK)

B

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the A73 main body ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
D54-1 (VC5) - A73-8 (VC5) Always Below 1 Ω
D54-1 (VC5) - Body ground Always 10 kΩ or higher



OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
D54-7 (AGND) - Body ground Always Below 1 Ω


Result
Result Proceed to
NG A
OK B


A

7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - INSTRUMENT PANEL JUNCTION BLOCK)

B

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - INSTRUMENT PANEL JUNCTION BLOCK)
7.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the A73 main body ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
D54-7 (AGND) - A73-16 (AGND) Always Below 1 Ω



OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY AMPLIFIER - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the A73 main body ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
D54-5 (TXCT) - A73-15 (TXCT) Always Below 1 Ω
D54-4 (CODE) - A73-5 (CODE) Always Below 1 Ω
D54-5 (TXCT) - Body ground Always 10 kΩ or higher
D54-4 (CODE) - Body ground Always 10 kΩ or higher



OK

9.REPLACE TRANSPONDER KEY AMPLIFIER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE TRANSPONDER KEY AMPLIFIER
a.

Temporarily replace the transponder key amplifier with a new or known good one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY AMPLIFIER>REMOVAL).



NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Key is inserted into ignition key cylinder.


b.

Turn the ignition switch off or ACC.



OK:

DTC B1410 is not output



OK

END (TRANSPONDER KEY AMPLIFIER WAS DEFECTIVE)

NG

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Replace the keys in which the DTC B1410 is stored, and perform the registration.



OK:

DTC B1410 is not output



OK

END (KEY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)