Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297684 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B1578  Immobiliser System Data Mismatch Key  


DESCRIPTION

The ECM stores this code when the combination meter assembly reference code and reference code from the main body ECU (multiplex network ECU) do not match, or when a communication error is detected between the main body ECU (network gateway ECU) and the ECM.

DTC Code DTC Detection Condition Trouble Area
B1578
·

The combination meter assembly reference code and the reference code from the main body ECU (network gateway ECU) do not match.

·

Communication error between the main body ECU (network gateway ECU) and the ECM.


·

Harness or connector

·

ECM

·

Instrument panel junction block assembly

·

Main body ECU (network gateway ECU)



WIRING DIAGRAM

B312647E03
2.75,2.177 4.385,2.667 1.635,0.49 10 false Main Body ECU (Network Gateway ECU) 0.854,1.917 1.792,2.458 0.938,0.542 10 false ECM 2.594,2.927 5.344,3.573 2.75,0.646 10 false Instrument Panel Junction Block Assembly 1.573,0.51 1.75,0.677 0.177,0.167 10 false 25 2.76,0.698 3.104,0.875 0.344,0.177 10 false IMO 1.167,0.688 1.469,0.865 0.302,0.177 10 false IMO 2.479,0.938 2.594,1.104 0.115,0.167 10 false 4 2.49,0.5 2.677,0.708 0.188,0.208 10 false 9 2.49,1.427 2.583,1.573 0.094,0.146 10 false 1 2.448,1.615 2.656,1.771 0.208,0.156 10 false D6 2.406,1.135 2.74,1.281 0.333,0.146 10 false A73 2.406,0.688 2.74,0.865 0.333,0.177 10 false A73 3.792,1.667 4.073,1.854 0.281,0.188 10 false MB 3.771,1.146 4.052,1.354 0.281,0.208 10 false MB 3.781,0.677 4.063,0.875 0.281,0.198 10 false MB 3.792,1.479 4,1.667 0.208,0.188 10 false 11 3.792,0.969 4,1.115 0.208,0.146 10 false 32 3.833,0.49 4,0.698 0.167,0.208 10 false 1 3.344,1.667 3.646,1.844 0.302,0.177 10 false GND 3.271,0.677 3.677,0.865 0.406,0.188 10 false BECU 3.229,1.146 3.635,1.354 0.406,0.208 10 false BMPX 1.531,0.688 1.823,0.865 0.292,0.177 10 false A35 0.396,1.083 0.75,1.281 0.354,0.198 10 false A36 0.469,0.896 0.667,1.073 0.198,0.177 10 false 4 0.75,1.083 1.104,1.271 0.354,0.188 10 false E01 5.667,0.323 6.729,0.625 1.063,0.302 10 false to MAIN Fuse 5.281,1.146 5.49,1.354 0.208,0.208 10 false 3C 5.281,1.667 5.49,1.865 0.208,0.198 10 false 3B 5.281,0.677 5.49,0.865 0.208,0.188 10 false 3A 5.271,1.479 5.438,1.635 0.167,0.156 10 false 18 5.281,0.979 5.5,1.125 0.219,0.146 10 false 19 5.281,0.49 5.5,0.698 0.219,0.208 10 false 27 6.365,0.823 6.708,0.969 0.344,0.146 10 false DCC 5.792,0.813 6.24,0.958 0.448,0.146 10 false ECU-B 5.792,1.323 6.323,1.5 0.531,0.177 10 false MPX-B 2.76,1.615 3.083,1.792 0.323,0.177 10 false GND 2.76,1.135 3.083,1.313 0.323,0.177 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (network gateway ECU) or ECM is replaced, refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC

OK:

DTC B1401, B1405, B1407 and B1408 is not output



OK

2.CHECK HARNESS AND CONNECTOR (BATTERY, BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY, BODY GROUND)
a.

Disconnect the A73 and D6 main body ECU (network gateway ECU) connectors.


b.

Disconnect the 3A, 3B and 3C instrument panel junction block assembly connectors.


c.
U146922E05
0.063,0.063 0.25,0.219 0.188,0.156 10 false *a 1.625,0.24 1.833,0.396 0.208,0.156 10 false 3C 1.635,1.792 1.844,1.948 0.208,0.156 10 false 3A

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
3A-27 - Body ground Always 11 to 14 V
3C-19 - Body ground Always 11 to 14 V


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
3B-18 - Body ground Always Below 1 Ω
A73-4 (GND) - Body ground Always Below 1 Ω
D6-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


U190239E02
3.844,0.792 3.927,1.01 true 1.656,0.813 1.583,1.01 true 0.615,0.813 0.552,1.01 true 0.073,0.052 0.26,0.208 0.188,0.156 10 false *a 2.073,0.25 2.323,0.406 0.25,0.156 10 false MB 2.167,1.354 2.385,1.51 0.219,0.156 10 false 3C 5.552,1.354 5.771,1.51 0.219,0.156 10 false 3A 5.552,0.115 5.75,0.271 0.198,0.156 10 false 3B 3.771,1.042 4.208,1.208 0.438,0.167 10 false BMPX 1.417,1.031 1.76,1.188 0.344,0.156 10 false GND 0.344,1.031 0.76,1.188 0.417,0.156 10 false BECU

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
MB-1 (BECU) - 3A-27 Always Below 1 Ω
MB-32 (BMPX) - 3C-19 Always Below 1 Ω
MB-11 (GND) - 3B-18 Always Below 1 Ω



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - ECM)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - ECM)
a.

Disconnect the A73 main body ECU (network gateway ECU) connector.


b.

Disconnect the A35 and A36 ECM connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
A73-9 (IMO) - Body ground Always Below 1 V
A35-25 (IMO) - Body ground Always Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
A73-9 (IMO) - A35-25 (IMO) Always Below 1 Ω
A36-4 (E01) - Body ground Always Below 1 Ω
A73-9 (IMO) - Body ground Always 10 kΩ or higher



OK

5.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ECM
a.

Temporarily replace the ECM with a new or known good one (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>ECM>REMOVAL).


b.

Register the ECU communication ID (Refer to Service Bulletin).



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

OK

END

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)