Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2090E _58 Vehicle Interior _060698 LIGHTING (INT) _0297690 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Luggage Compartment Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) detects the condition of the luggage compartment door lock assembly using this circuit.

WIRING DIAGRAM

E249232E03
1.594,1.406 2.885,1.75 1.292,0.344 10 false Luggage Door Closer Assembly 4.167,1.938 5.792,2.302 1.625,0.365 10 false Instrument Panel Junction Block Assembly 5.51,2.906 7.042,3.271 1.531,0.365 10 false Main Body ECU (Network Gateway ECU) 1.594,1.26 1.781,1.427 0.188,0.167 10 false J3 4.552,0.948 4.75,1.094 0.198,0.146 10 false 3D 4.552,0.76 4.74,0.927 0.188,0.167 10 false 26 5.552,0.938 5.802,1.094 0.25,0.156 10 false MB 5.552,0.771 5.729,0.938 0.177,0.167 10 false 12 2.875,0.854 3.021,1.01 0.146,0.156 10 false 3 2.615,0.854 2.813,1.01 0.198,0.156 10 false D+ 1.583,0.854 1.698,1.031 0.115,0.177 10 false 2 1.74,0.854 1.875,1.01 0.135,0.156 10 false E

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

OK:

Normal conditions listed above are displayed.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Luggage Courtesy SW Luggage compartment door courtesy switch signal/ON or OFF ON: Luggage compartment door open
OFF: Luggage compartment door closed
-



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT LUGGAGE DOOR CLOSER ASSEMBLY
2.INSPECT LUGGAGE DOOR CLOSER ASSEMBLY
a.

Remove the luggage door closer assembly (See page Vehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK>REMOVAL).


b.
B175598E02
0.102,0.201 0.259,0.347 0.156,0.146 10 *b 1.646,0.131 1.788,0.275 0.142,0.144 10 *c 2.497,0.41 2.653,0.550 0.156,0.140 10 *a 1.249,0.383 1.609,0.222 false 0.93,0.397 0.314,0.291 false 2.808,1.465 2.919,1.608 0.111,0.143 10 E 2.289,1.491 2.489,1.634 0.201,0.143 10 D+ 2.394,1.223 2.394,1.491 false 2.59,1.223 2.786,1.538 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Door Lock Condition Specified Condition
3 (D+) - 2 (E) Open (Unlock) Below 1 Ω
3 (D+) - 2 (E) Close (Lock) 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Luggage Door Closer Assembly)
*b Close (Lock)
*c Open (Unlock)


OK

3.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR CLOSER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE LUGGAGE DOOR CLOSER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR CLOSER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Disconnect the J3 luggage door closer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J3-3 (D+) - 3D-26 Always Below 1 Ω
J3-3 (D+) - Body ground Always 10 kΩ or higher
J3-2 (E) - Body ground Always Below 1 Ω




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U147277E03
0.146,0.083 0.333,0.24 0.188,0.156 10 false *a 2.031,0.5 2.26,0.656 0.229,0.156 10 false MB 5.667,0.313 5.865,0.469 0.198,0.156 10 false 3D

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3D-26 - MB-12 Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY