Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2090E _58 Vehicle Interior _060698 LIGHTING (INT) _0297690 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) controls the operation of the map light assembly

WIRING DIAGRAM

E249234E03
5.135,2.844 6.646,3.198 1.51,0.354 10 false Main Body ECU (Network Gateway ECU) 0.208,1.448 1.031,1.646 0.823,0.198 10 false from Battery 2.458,1.615 2.896,1.792 0.438,0.177 10 false DOME 1.708,1.583 2.031,1.74 0.323,0.156 10 false DCC 3.365,2.219 4.656,2.417 1.292,0.198 10 false Map Light Assembly 5.146,2.667 5.365,2.844 0.219,0.177 10 false D5 5.375,1.073 5.49,1.25 0.115,0.177 10 false 7 4.823,1.073 4.938,1.24 0.115,0.167 10 false 3 4.813,1.625 4.917,1.792 0.104,0.167 10 false 1 3.25,1.344 3.354,1.521 0.104,0.177 10 false 2 3.375,2.063 3.604,2.219 0.229,0.156 10 false K3 3.698,1.125 4.125,1.281 0.427,0.156 10 false DOOR 5.563,1.188 6.021,1.385 0.458,0.198 10 false DOMR 4.323,0.906 4.75,1.24 0.427,0.333 10 false DOOR SW 4.479,1.646 4.792,1.823 0.313,0.177 10 false GND 4.354,1.469 4.688,1.698 0.333,0.229 10 false OFF 3.958,1.854 4.188,2.01 0.229,0.156 10 false ON 3.406,1.583 3.604,1.75 0.198,0.167 10 false +B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the lights operate.

OK:

Map light fades in.


Main Body
Tester Display Test Part Control Range Diagnostic Note
Illuminated Entry System Map light assembly ON/OFF -



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL).


b.

Inspect the map light assembly (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION).

OK:

Map light assembly is normal.




OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - MAP LIGHT ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BATTERY - MAP LIGHT ASSEMBLY)
a.

Disconnect the K3 map light assembly connector.


b.
U147280E01
0.191,0.181 0.377,0.342 0.186,0.161 10 *a 0.459,1.004 0.646,1.160 0.188,0.156 10 K3 1.609,1.755 1.805,1.895 0.196,0.140 10 +B 1.724,1.729 1.724,1.348 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K3-2 (+B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to map light assembly)


OK

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the K3 map light assembly connector.


b.

Disconnect the D5 main body ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K3-3 (DOOR SW) - D5-7 (DOMR) Always Below 1 Ω
D5-7 (DOMR) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR