Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2090E _58 Vehicle Interior _060698 LIGHTING (INT) _0297690 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Door Courtesy Light Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) controls the operation of the courtesy light assembly.

WIRING DIAGRAM

E249227E02
2.656,1.395 4.943,1.546 2.287,0.150 10 Courtesy Light Assembly RH*1/LH*2 2.656,2.75 4.928,2.900 2.272,0.150 10 Courtesy Light Assembly LH*1/RH*2 2.67,1.246 3.388,1.383 0.718,0.137 10 F4*1, E2*2 0.279,3.454 1.057,3.591 0.778,0.137 10 *1: for RHD 1.259,3.454 2.037,3.591 0.778,0.137 10 *2: for LHD 2.67,2.601 3.383,2.738 0.713,0.137 10 E2*1, F4*2 5.645,3.103 7.158,3.411 1.513,0.309 10 Main body ECU (Network gateway ECU) 5.659,2.954 5.855,3.091 0.196,0.137 10 D5 5.92,0.849 6.015,0.987 0.095,0.138 10 5 5.92,2.204 6.015,2.342 0.095,0.138 10 6 4.153,0.849 4.247,0.987 0.095,0.138 10 1 4.153,2.204 4.247,2.342 0.095,0.138 10 1 2.874,0.849 2.968,0.987 0.095,0.138 10 2 2.874,2.204 2.968,2.342 0.095,0.138 10 2 0.958,1.096 1.280,1.234 0.322,0.137 10 DCC 1.65,1.096 2.085,1.234 0.435,0.137 10 DOME 0.158,0.872 0.623,1.191 0.465,0.319 10 from Battery 6.088,1.041 6.604,1.181 0.516,0.140 10 FLCL*2 6.088,2.393 6.625,2.533 0.537,0.140 10 FRCL*2 6.088,2.199 6.592,2.339 0.504,0.140 10 FLCL*1 6.088,0.849 6.601,0.989 0.513,0.140 10 FRCL*1

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the lights operate.

OK:

Each light comes on.


Main Body
Tester Display Test Part Control Range Diagnostic Note
Driver Courtesy Lamp Driver courtesy light ON/OFF -
Passenger Courtesy Lamp Passenger courtesy light ON/OFF -


Result:
Result Proceed to
All lights do not come on A
Courtesy light assembly RH does not come on B
Courtesy light assembly LH does not come on C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (BATTERY - COURTESY LIGHT)

C

5.CHECK HARNESS AND CONNECTOR (BATTERY - COURTESY LIGHT)
2.CHECK HARNESS AND CONNECTOR (BATTERY - COURTESY LIGHT)
a.

Disconnect the F4 courtesy light assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F4-2 - Body ground Always 11 to 14 V




OK

3.INSPECT COURTESY LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COURTESY LIGHT ASSEMBLY
a.

Remove the courtesy light assembly RH (See page Vehicle Interior>LIGHTING (INT)>DOOR COURTESY LIGHT>REMOVAL).


b.

Inspect the courtesy light assembly RH (See page Vehicle Interior>LIGHTING (INT)>DOOR COURTESY LIGHT>INSPECTION).


OK:

Courtesy light assembly RH is normal.



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - COURTESY LIGHT AND BODY GROUND)

NG

REPLACE COURTESY LIGHT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - COURTESY LIGHT AND BODY GROUND)
a.

Disconnect the D5 main body ECU (network gateway ECU) connector.


b.

Disconnect the F4 courtesy light assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
D5-5 (FRCL) - F4-1 Always Below 1 Ω
F4-1 - Body ground Always 10 kΩ or higher


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
D5-6 (FRCL) - F4-1 Always Below 1 Ω
F4-1 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BATTERY - COURTESY LIGHT)
a.

Disconnect the E2 courtesy light assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E2-2 - Body ground Always 11 to 14 V




OK

6.INSPECT COURTESY LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT COURTESY LIGHT ASSEMBLY
a.

Remove the courtesy light assembly LH (See page Vehicle Interior>LIGHTING (INT)>DOOR COURTESY LIGHT>REMOVAL).


b.

Inspect the courtesy light assembly LH (See page Vehicle Interior>LIGHTING (INT)>DOOR COURTESY LIGHT>INSPECTION).


OK:

Courtesy light assembly LH is normal.



OK

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - COURTESY LIGHT AND BODY GROUND)

NG

REPLACE COURTESY LIGHT ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - COURTESY LIGHT AND BODY GROUND)
a.

Disconnect the D5 main body ECU (network gateway ECU) connector.


b.

Disconnect the E2 courtesy light assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
D5-6 (FLCL) - E2-1 Always Below 1 Ω
E2-1 - Body ground Always 10 kΩ or higher


Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
D5-5 (FLCL) - E2-1 Always Below 1 Ω
E2-1 - Body ground Always 10 kΩ or higher



OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR