Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM2090E _58 Vehicle Interior _060699 METER / GAUGE / DISPLAY _0297701 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter detects the fuel sender gauge malfunction.

DTC No. DTC Detection Condition Trouble Area
B1500 When combination meter detects fuel sender gauge malfunction
·

Harness or connector

·

Combination meter assembly

·

Fuel sender gauge assembly

·

No. 2 Fuel sender gauge assembly

·

Fuel suction tube assembly with pump and gauge

·

Fuel tank return tube sub-assembly



WIRING DIAGRAM

E246788E07
3.917,5.104 6.146,5.51 2.229,0.406 10 false FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE 4.104,4.469 6.417,4.667 2.313,0.198 10 false FUEL SENDER GAUGE ASSEMBLY 3.927,1.844 6.667,2.146 2.74,0.302 10 false NO. 2 FUEL SENDER GAUGE ASSEMBLY 3.917,4.927 4.854,5.115 0.938,0.188 10 false G7 3.917,2.448 7.031,2.771 3.115,0.323 10 false FUEL TANK RETURN TUBE SUB-ASSEMBLY 3.917,2.292 4.75,2.479 0.833,0.188 10 false G6 0.625,5.323 2.979,5.729 2.354,0.406 10 false COMBINATION METER ASSEMBLY 0.625,5.167 1.229,5.344 0.604,0.177 10 false D7 1.979,0.792 2.667,0.969 0.688,0.177 10 false 27 1.76,0.896 2.833,1.115 1.073,0.219 10 false L 3.948,3.396 4.219,3.604 0.271,0.208 10 false FS+ 3.771,3.406 4.177,3.573 0.406,0.167 10 false 1 3.771,1.323 4.229,1.49 0.458,0.167 10 false 2 3.771,0.792 4.24,0.958 0.469,0.167 10 false 1 4.323,1.313 4.802,1.479 0.479,0.167 10 false 2 4.323,0.802 4.927,0.958 0.604,0.156 10 false 3 3.771,3.938 4.354,4.104 0.583,0.167 10 false 2 4.323,3.406 4.927,3.573 0.604,0.167 10 false 1 4.323,3.927 5.073,4.104 0.75,0.177 10 false 2 1.979,3.927 2.521,4.094 0.542,0.167 10 false 28 3.948,3.896 4.219,4.104 0.271,0.208 10 false FS- 1.625,4 1.896,4.208 0.271,0.208 10 false FS- 3.969,0.792 4.115,0.969 0.146,0.177 10 false L 3.969,1.323 4.24,1.531 0.271,0.208 10 false FS+

PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the tester, read the Data List.

Combination Meter
Item Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel sender gauge input
Min.: 0
Max.: 127.5
Fuel sender input value Unit: Liter

OK:

Fuel input signal displayed on the tester is approximately the same as the fuel receiver gauge indication.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.INSPECT FUEL SENDER GAUGE ASSEMBLY
2.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Inspect the fuel sender gauge assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION).



OK

3.INSPECT FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

3.INSPECT FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
U190431E02
1.979,0.688 2.271,0.156 true 1.448,0.688 1.156,0.156 true 0.073,0.063 0.26,0.229 0.188,0.167 10 false *a 0.135,1.906 0.323,2.073 0.188,0.167 10 false *a 0.656,0.979 0.948,1.135 0.292,0.156 10 false G7 2.323,0.052 2.75,0.208 0.427,0.156 10 false FS+ 0.885,0.042 1.323,0.198 0.438,0.156 10 false FS-

a.

Remove the fuel suction tube assembly with pump and gauge (See page Engine / Hybrid System>FA20 FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connector Condition Specified Condition
G7-1 (FS+) - 1 Always Below 1 Ω
G7-2 (FS-) - 2 Always Below 1 Ω



Text in Illustration
*a Component without harness connected
(Fuel Suction Tube Assembly with Pump and Gauge)


OK

4.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

4.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY
a.

Remove the No. 2 fuel sender gauge assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Inspect the No. 2 fuel sender gauge assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION).



OK

5.INSPECT FUEL TANK RETURN TUBE SUB-ASSEMBLY

NG

REPLACE NO. 2 FUEL SENDER GAUGE ASSEMBLY

5.INSPECT FUEL TANK RETURN TUBE SUB-ASSEMBLY
U190432E02
2.031,0.781 2.333,0.25 true 1.385,0.792 1.094,0.26 true 2.375,0.125 2.802,0.281 0.427,0.156 10 false L 0.781,0.146 1.219,0.302 0.438,0.156 10 false FS+ 0.583,1.031 0.875,1.188 0.292,0.156 10 false G6 0.073,0.073 0.365,0.229 0.292,0.156 10 false *a 0.156,2.146 0.448,2.302 0.292,0.156 10 false *a

a.

Remove the fuel tank return tube sub-assembly (See page Engine / Hybrid System>FA20 FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connector Condition Specified Condition
G6-1 (L) - 3 Always Below 1 Ω
G6-2 (FS+) - 2 Always Below 1 Ω



Text in Illustration
*a Component without harness connected
(Fuel Tank Return Tube Sub-assembly)


OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)

NG

REPLACE FUEL TANK RETURN TUBE SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
a.

Disconnect the D7 combination meter assembly connector.


b.

Disconnect the G7 fuel suction tube assembly with pump and gauge connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connector Condition Specified Condition
D7-28 (FS-) - G7-2 (FS-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connector Condition Specified Condition
D7-28 (FS-) or G7-2 (FS-) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE - FUEL TANK RETURN TUBE SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE - FUEL TANK RETURN TUBE SUB-ASSEMBLY)
a.

Disconnect the G7 fuel suction tube assembly with pump and gauge connector.


b.

Disconnect the G6 fuel tank return tube sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connector Condition Specified Condition
D7-1 (FS+) - G6-2 (FS+) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connector Condition Specified Condition
D7-1 (FS+) or G6-2 (FS+) - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL TANK RETURN TUBE SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL TANK RETURN TUBE SUB-ASSEMBLY)
a.

Disconnect the D7 combination meter assembly connector.


b.

Disconnect the G6 fuel tank return tube sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connector Condition Specified Condition
D7-27 (L) - G6-1 (L) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connector Condition Specified Condition
D7-27 (L) or G6-1 (L) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR